AEG Builtin wine cooler SWD81800G1 User Manual

5. WHAT TO DO IF…
WARNING!
Before troubleshooting, discon-
nect the mains plug from the
mains socket.
Only a qualified electrician or
competent person must do the
troubleshooting that is not in this
manual.
ProblemPossible causeSolution
The appliance does
not operate. The
lamp does not oper-
ate.The appliance is switched
off.Switch on the appliance.
 The mains plug is not
connected to the mains
socket correctly.Connect the mains plug to
the mains socket correctly.
 The appliance has no
power. There is no...

ProblemPossible causeSolution
 Products prevent that wa-
ter flows into the water
collector.Make sure that products
do not touch the rear
plate.
Water flows on the
ground.The melting water outlet
does not flow in the evap-
orative tray above the
compressor.Attach the melting water
outlet to the evaporative
tray.
The temperature in
the appliance is too
low.The temperature regula-
tor is not set correctly.Set a higher temperature.
The temperature in
the appliance is too
high.The temperature regula-
tor is...

Remove the lamp cover by pressing it in-
wards with a tool (e.g. screwdriver) to
free the rear side hookings.
At the same time, free the middle hook
and slide off the cover in the direction of
the arrows.
Replace the used lamp with a new lamp
of the same type and specifically de-
signed for household appliances and
having the same characteristics.
Install the lamp cover.
Connect the mains plug to the mains
socket.
Open the door. Make sure that the lamp
comes on.
5.2 Closing the door
1.Clean the door...

6. INSTALLATION
6.1 Positioning
WARNING!
If you are discarding an old appli-
ance that has a lock or catch on
the door, you must ensure that it
is made unusable to prevent
young children being trapped in-
side.
The appliance shall have the
plug accessible after installation.
Install this appliance at a location where
the ambient temperature corresponds to
the climate class indicated on the rating
plate of the appliance:
Cli-
mate
classAmbient temperature
SN+10°C to + 32°C
N+16°C to + 32°C
ST+16°C to +...

13 amp ASTA approved (BS 1362) fuse
must be used.WARNING!
A cut off plug inserted into a 13
amp socket is a serious safety
(shock) hazard. Ensure that it is
disposed of safely.
6.3 Ventilation requirements
5 cmmin.
200 cm2
min.
200 cm2
The airflow behind the appliance must
be sufficient.
6.4 Installing the appliance
CAUTION!
Make sure that the mains cable
can move freely.Do the following steps:
Apply the adhesive sealing strip to the
appliance as shown in figure.
ENGLISH15 

Install the appliance in the niche.
Attach the appliance to the niche with 4
screws.
Fix the covers on the screws.
Do a final check to make sure that: • All screws are tightened.
16www.aeg.com 

• The sealing strip is attached tightly to
the cabinet.• The door opens and closes correctly.
6.5 Assembly instructions for the compensator lower part of the
door
With the door open, loosen the two
screws situated in the lower part with-
out unscrewing them completely.
Position the steel compensator as in-
dicated in the figure and insert the up-
per part under the head of the screws.
Align the compensator with the steel
door panel and tighten the screws.
Insert the steel carter inside the com-
pensator...

7. NOISES
There are some sounds during normal
running (compressor, refrigerant circula-
tion).
BRRR!HISSS!
CLICK!
BLUBB!
CRACK!
SSSRR
R!
OK
CLICK!CLICK!SSSRRR!SSSRRR!
BRRR!BRRR!HISSS!HISSS!
18www.aeg.com 

BLUBB!BLUBB!CRACK!CRACK!
8. TECHNICAL DATA
   
Dimension of the recess  
 Height1780 mm
 Width560 mm
 Depth550 mm
Voltage 230-240 V
Frequency 50 Hz
The technical information are situated in
the rating plate on the internal left side
of the appliance and in the energy label.
9. ENVIRONMENT CONCERNS
Recycle the materials with the
symbol  . Put the packaging in
applicable containers to recycle it.
Help protect the environment and
human health and to recycle waste
of electrical and electronicappliances. Do...

www.aeg.com/shop
222354132-A-172012