AEG Freestanding dishwasher F88709M0P User Manual

dispenser is activated (factory
setting).
3. Press  Start to change the setting. = the rinse aid dispenser is
deactivated.
4. Press the on/off button to confirm
the setting.7.  OPTIONSDesired options must be
activated every time before
you start a programme.
It is not possible to activate
or deactivate options while a
programme is running.Not all options are
compatible with each other.
If you have selected non
compatible options, the
appliance will automatically
deactivate one or more of
them. Only the...

8. BEFORE FIRST USE1. Make sure that the current level of
the water softener agrees with the
hardness of the water supply. If
not, adjust the level of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not load the
baskets.
When you start a programme, the
appliance can take up to 5 minutes to
recharge the resin in the water...

Fill the rinse aid dispenser
when the indicator ( A)
becomes clear.9.  DAILY USE1.Open the water tap.
2. Press the on/off button to activate
the appliance.
Make sure that the appliance is in
programme selection mode. • If the salt indicator is on, fill thesalt container.
• If the rinse aid indicator is on, fill the rinse aid dispenser.
3. Load the baskets.
4. Add the detergent. If you use multi-
tablets, activate the option Multitab.
5. Set and start the correct programme
for the type of load and the...

hour will decrease with steps of 1
minute.
When the countdown is completed, the programme starts and the indicator of
the running phase comes on. The delay indicator goes off.Opening the door while the
appliance operates
If you open the door while a programme
is running, the appliance stops. When you close the door, the appliance
continues from the point of interruption.
Cancelling the delay start while
the countdown operates
When you cancel the delay start you have to set the programme and options...

completely reached and washed by
the water released from the spray arm nozzles. Make sure that items do nottouch or cover each other.
• You can use dishwasher detergent, rinse aid and salt separately or you
can use the multi-tablets (e.g. ''3in1'',
''4in1'', ''All in 1''). Follow the
instructions written on the packaging.
• Select the programme according to the type of load and degree of soil.
With the ECO programme you have
the most efficient use of water...

• The spray arms are not clogged.
• There is dishwasher salt and rinse aid (unless you use multi- tablets).
• The position of the items in the baskets is correct.
• The programme is applicable for the type of load and for the degree of
soil.
• The correct quantity of detergent is used.10.6  Unloading the baskets
1. Let the tableware cool down before
you remove it from the appliance.
Hot items can be easily damaged.
2. First remove items from the lower
basket, then from the upper basket.At the end of the...

5.Make sure that there are no residues
of food or soil in or around the edge
of the sump.
6. Put back in place the flat filter ( A).
Make sure that it is correctly
positioned under the 2 guides.
7. Reassemble the filters ( B) and ( C).
8. Put back the filter ( B) in the flat filter
( A ). Turn it clockwise until it locks.
CAUTION!
An incorrect position of the
filters can cause bad
washing results and damage
to the appliance.11.2  Cleaning the spray arms
Do not remove the spray arms. If the
holes in the...

With some problems, the display
shows an alarm code.Problem and alarm codePossible solutionYou cannot activate the ap-
pliance.• Make sure that the mains plug is connected to the mains socket.
• Make sure that there is no damaged fuse in the fuse box.The programme does not
start.• Make sure that the appliance door is closed. • Press  Start.
• If the delay start is set, cancel the setting or wait for the end of the countdown.
• The appliance has started the procedure to recharge the resin inside the water...

ProblemPossible solutionThe dishes are wet.• The programme does not have a drying phase or hasa drying phase with low temperature.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.
• The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and
use rinse aid and multi-tablets together.Refer to " Hints and tips " for
other possible causes.13.  TECHNICAL INFORMATIONDimensionsWidth / height / depth (mm)596 / 850 /...

www.aeg.com/shop117904881-A-272014