AEG Integrated dishwasher F50513VI0 User Manual

							7.1 ExtraHygiene
With this option you have better hygiene results. During the last rinsing phase, the
temperature stays at 70 °C for at least 10
minutes.How to activate ExtraHygiene
Press , the related indicator comes on
If the option is not applicable to the
programme, the related indicator does not come on or it flashes quickly for afew seconds and then goes off.
The display shows the updated
programme duration.
7.2  XtraDry
Activate this option when you want to
boost the drying performance. With the
use of this option, the duration of some
programmes, water consumption and
the last rinse temperature can be
affected.
The option XtraDry is not a permanent
option and must be selected at every
cycle.How to activate XtraDry
Press . The related indicator comes
on.
If the option is not applicable to the
program, the related indicator does not
come on or it flashes quickly for a fewseconds and then goes off.
The display shows the updated program
duration.
8.  BEFORE FIRST USE1. Make sure that the current level of
the water softener agrees with the
hardness of the water supply. If
not, adjust the level of the water
softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any
processing residuals that can still be
inside the appliance. Do not use
detergent and do not load the
baskets.
When you start a programme, the
appliance can take up to 5 minutes to
recharge the resin in the water softener. It seems that the appliance is not
working. The washing phase starts only
after this procedure is completed. The
procedure will be repeated periodically.8.1  The salt containerCAUTION!
Only use salt specifically designed for dishwashers.
The salt is used to recharge the resin in
the water softener and to assure good washing results in the daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt
container (Only for the first time).
3. Fill the salt container with dishwasher
salt.
4. Remove the salt around the opening
of the salt container.
ENGLISH11      
						

							5.Turn the cap of the salt container
clockwise to close the salt container.CAUTION!
Water and salt can come out of the salt container when
you fill it. After you fill the
salt container, immediately
start a programme to
prevent corrosion.8.2  How to fill the rinse aid
dispenserCAUTION!
Only use rinse aid
specifically designed for dishwashers.
1. Press the release button ( D) to open
the lid ( C).
2. Pour the rinse aid in the dispenser ( A)
until the liquid reaches the fill level
'max'.
3. Remove the spilled rinse aid with an
absorbent cloth to prevent too much
foam.
4. Close the lid. Make sure that the
release button locks into position.
You can turn the selector of
the released quantity ( B)
between position 1 (lowest
quantity) and position 4 or 6
(highest quantity).9.  DAILY USE1.Open the water tap.
2. Press the on/off button to activate
the appliance.
Make sure that the appliance is in
programme selection mode. • If the salt indicator is on, fill thesalt container.
• If the rinse aid indicator is on, fill the rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.5.Set and start the correct programme
for the type of load and the degree
of soil.www.aeg.com12 AB
D
C MAX1234+-
AB
DC    
						

							9.1 Using the detergent
1.Press the release button ( B) to open
the lid ( C).
2. Put the detergent, in powder or
tablets, in the compartment ( A).
3. If the programme has a prewash
phase, put a small quantity of
detergent in the compartment ( D).
4. Close the lid. Make sure that the
release button locks into position.
9.2  Setting and starting a
programmeThe Auto Off function
This function decreases energy
consumption by deactivating
automatically the appliance when it is not
operating.
The function comes into operation:
• 5 minutes after the completion of the programme.
• After 5 minutes if the programme has not started.
Starting a programme
1. Keep the appliance door ajar.
2. Press the on/off button to activate
the appliance. Make sure that the
appliance is in programme selection
mode.
3. Press repeatedly 
 or
 until the display shows
the number of the programme you
want to start. The display will show
the programme number for
approximately 3 seconds and then
show the programme duration.
4. Set the applicable options.
5. Close the appliance door to start the
programme.
Starting a programme with
delay start
1. Set a programme.
2. Press 
 again and again until the
display shows the delay time you
want to set (from 1 to 24 hours).
The delay indicator comes on.
3. Close the appliance door to start the
countdown.
While a countdown is running it is
possible to increase the delay time but not to change the selection of the
programme and options.
When the countdown is completed, the programme starts.
Opening the door while the
appliance operates
If you open the door while a programme
is running, the appliance stops. It may
affect the energy consumption and the
programme duration. When you close
the door, the appliance continues from
the point of interruption.
If the door is opened for
more than 30 seconds
during the drying phase, the
running programme will end.ENGLISH1330
20
A B
D
C 2030
B
A D
C      
						

							Cancelling the delay start while
the countdown operates
When you cancel the delay start you
have to set the programme and options
again.
Press and hold  Reset until the appliance
is in programme selection mode.Cancelling the programme
Press and hold  Reset until the appliance
is in programme selection mode.
Make sure that there is detergent in the detergent dispenser before you start anew programme.End of the programme
When the programme is completed the
display shows 0:00 .
1. Press the on/off button or wait for
the Auto Off function to
automatically deactivate the
appliance.
2. Close the water tap.
10.  HINTS AND TIPS10.1  General
The following hints will ensure optimal
cleaning and drying results in daily use
and also help to protect the
environment.
• Remove larger residues of food from the dishes into the waste bin.
• Do not pre-rinse dishes by hand. When needed, use the prewash
programme (if available) or select a
programme with a prewash phase.
• Always use the whole space of the baskets.
• When loading the appliance, make sure that the dishes can be
completely reached and washed by
the water released from the spray arm
nozzles. Make sure that items do not
touch or cover each other.
• You can use dishwasher detergent, rinse aid and salt separately or you
can use the multi-tablets (e.g. ''3in1'',
''4in1'', ''All in 1''). Follow the
instructions written on the packaging.
• Select the programme according to
the type of load and degree of soil.With the ECO programme you have
the most efficient use of water and energy consumption for crockery and
cutlery with normal soil.10.2  Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent for dishwasher. Other products can
cause damage to the appliance.
• In areas with hard and very hard water
we recommend to use solo-detergent
(powder, gel, tablets without
additional functions), rinse aid and
salt separately for optimal cleaning
and drying results.
• At least once a month run the appliance with the use of appliance
cleaner which is particularly suitable
for this purpose.
• Detergent tablets do not fully dissolve with short programmes. To prevent
detergent residues on the tableware,
we recommend that you use the
tablets with long programmes.
• Do not use more than the correct quantity of detergent. Refer to the
instructions on the detergent
packaging.10.3  What to do if you want to
stop using multi-tablets
Before you start to use separately
detergent, salt and rinse aid do the
following procedure.
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the shortest programme with a
rinsing phase. Do not add detergent
and do not load the baskets.
4. When the programme is completed,
adjust the water softener according
to the water hardness in your area.
5. Adjust the released quantity of rinse
aid.
www.aeg.com14 
						

							6.Activate the rinse aid empty
notification.10.4  Loading the baskets
• Only use the appliance to wash items
that are dishwasher-safe.
• Do not put in the appliance items made of wood, horn, aluminium,
pewter and copper.
• Do not put in the appliance items that can absorb water (sponges,
household cloths).
• Remove remaining food from the items.
• Make soft the remaining burned food on the items.
• Put hollow items (cups, glasses and pans) with the opening down.
• Make sure that cutlery and dishes do not bond together. Mix spoons withother cutlery.
• Make sure that glasses do not touch other glasses.
• Put small items in the cutlery basket. • Put light items in the upper basket. Make sure that the items do not
move.
• Make sure that the spray arm can move freely before you start a
programme.
10.5  Before starting a
programme
Make sure that:
• The filters are clean and correctly installed.
• The cap of the salt container is tight.
• The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets).
• The position of the items in the baskets is correct.
• The programme is applicable for the type of load and for the degree of
soil.
• The correct quantity of detergent is used.10.6  Unloading the baskets
1.Let the tableware cool down before
you remove it from the appliance.
Hot items can be easily damaged.
2. First remove items from the lower
basket, then from the upper basket.
At the end of the program
water can still remain on the
sides and on the door of the
appliance.11.  CARE AND CLEANINGWARNING!
Before maintenance,
deactivate the appliance and
disconnect the mains plug
from the main socket.Dirty filters and clogged
spray arms decrease the
washing results. Make a
check regularly and, if
necessary, clean them.11.1  Cleaning the filters
The filter system is made of 3 parts.
1.Turn the filter ( B) counterclockwise
and remove it.
ENGLISH15   C BA  
						

							2.Remove the filter ( C) out of filter ( B). 
3. Remove the flat filter ( A).
4. Wash the filters.
5.Make sure that there are no residues
of food or soil in or around the edge
of the sump.
6. Put back in place the flat filter ( A).
Make sure that it is correctly
positioned under the 2 guides.
7. Reassemble the filters ( B) and ( C).
8. Put back the filter ( B) in the flat filter
( A ). Turn it clockwise until it locks.
CAUTION!
An incorrect position of the
filters can cause bad
washing results and damage
to the appliance.11.2  External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive cleaning pads or solvents.
11.3  Internal cleaning
• Carefully clean the appliance,
including the rubber gasket of the
door, with a soft damp cloth.
• If you regularly use short duration programmes, these can leave
deposits of grease and limescale
inside the appliance. To prevent this,
we recommend to run long duration
programmes at least 2 times per month.
www.aeg.com16        
						

							• To maintain the performance of yourappliance at its best, we recommendto use monthly a specific cleaning
product for dishwashers. Followcarefully the instructions on the
packaging of the product.12.  TROUBLESHOOTINGIf the appliance does not start or it stops
during operation. Before you contact an Authorised Service Centre, check if youcan solve the problem by yourself with
the help of the information in the table.WARNING!
Repairs not properly done
may result in serious risk to
the safety of the user. Any
repairs must be performed
by qualified personnel.With some problems, the display
shows an alarm code.
The majority of problems that can occur can be solved without the need
to contact an Authorised Service
Centre.Problem and alarm codePossible cause and solutionYou cannot activate the ap-
pliance.• Make sure that the mains plug is connected to the mains socket.
• Make sure that there is no damaged fuse in the fuse box.The program does not start.• Make sure that the appliance door is closed.• If the delay start is set, cancel the setting or wait for the end of the countdown.
• The appliance has started the procedure to recharge the resin inside the water softener. The duration of the
procedure is approximately 5 minutes.The appliance does not fill
with water.
The display shows 
.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For this information, contact your local waterauthority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clogged.
• Make sure that the inlet hose has no kinks or bends.The appliance does not
drain the water.
The display shows 
.
• Make sure that the sink spigot is not clogged.
• Make sure that the filter in the outlet hose is not clog- ged.
• Make sure that the interior filter system is not clogged.
• Make sure that the drain hose has no kinks or bends.The anti-flood device is on.
The display shows 
.
• Close the water tap and contact an Authorised Service Centre.ENGLISH17     
						

							Problem and alarm codePossible cause and solutionThe appliance stops and
starts more times during op-
eration.• It is normal. It provides optimal cleaning results and en- ergy savings.The program lasts too long.• If the delayed start option is set, cancel the delay settingor wait for the end of the countdown.The remaining time in the
display increases and skips
nearly to the end of program
time.• This is not a defect. The appliance is working correctly.Small leak from the appli-
ance door.• The appliance is not levelled. Loosen or tighten the ad- justable feet (if applicable).
• The appliance door is not centred on the tub. Adjust the rear foot (if applicable).The appliance door is diffi-
cult to close.• The appliance is not levelled. Loosen or tighten the ad- justable feet (if applicable).
• Parts of the tableware are protruding from the baskets.Rattling/knocking sounds
from inside the appliance.• The tableware is not properly arranged in the baskets. Refer to basket loading leaflet.
• Make sure that the spray arms can rotate freely.The appliance trips the cir-
cuit-beaker.• The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and
the capacity of the meter or turn off one of the applian-
ces in use.
• Internal electrical fault of the appliance. Contact an Au- thorised Service Centre.Refer to  "Before first use" , 
"Daily use" , or "Hints and
tips"  for other possible
causes.
Once you have checked the appliance,
deactivate and activate the appliance. If
the problem occurs again, contact an
Authorised Service Centre.
For alarm codes not described in the
table, contact an Authorised Service
Centre.12.1  The washing and drying results are not satisfactoryProblemPossible cause and solutionPoor washing results.• Refer to  "Daily use" , "Hints and tips"  and basket
loading leaflet.
• Use more intensive washing programmes.
• Clean spray arm jets and filter. Refer to  "Care and
Cleaning" .www.aeg.com18  
						

							ProblemPossible cause and solutionPoor drying results.• Tableware has been left for too long inside a closedappliance.
• There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level.
• Plastic items may need to be towel dried.
• For the best drying performance activate the option XtraDry.
• We recommend to always use rinse aid, even in com- bination with multi-tablets.There are whitish streaks or
bluish layers on glasses and
dishes.• The release quantity of rinse aid is too much. Adjust the rinse aid level to a lower level.
• The quantity of detergent is too much.There are stains and dry water
drops on glasses and dishes.• The released quantity of rinse aid is not sufficient. Ad- just the rinse aid level to a higher level.
• The quality of the rinse aid can be the cause.The dishes are wet.• For the best drying performance activate the option XtraDry.
• The programme does not have a drying phase or has a drying phase with low temperature.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.
• The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and
use rinse aid and multi-tablets together.
• Keep the dishwasher door ajar for some time before removing tableware.The interior of the appliance is
wet.• This is not a defect of the appliance. it is caused by the humidity in the air that condenses on the walls.Unusual foam during washing.• Use the detergent for dishwashers only.• There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre.Traces of rust on cutlery.• There is too much salt in the water used for washing. Refer to  "The water softener" .
• Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close to-
gether.There are residues of deter-
gent in the dispenser at the
end of the programme.• The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
• Water cannot wash away the detergent from the dis- penser. Make sure that the spray arm is not blocked or
clogged.
• Make sure that items in the baskets do not impede the lid of the detergent dispenser from opening.Odours inside the appliance.• Refer to  "Internal cleaning" .ENGLISH19 
						

							ProblemPossible cause and solutionLimescale deposits on the ta-
bleware, on the tub and on
the inside of the door.• The level of salt is low, check the refill indicator.
• The cap of the salt container is loose. • Your tap water is hard. Refer to  "The water softener".
• Even using multi-functional tabs use salt and set re- generation of the water softener. Refer to  "The water
softener" .
• If lime scale deposits still remain, clean the appliance with appliance cleaners which are particularly suitable
for this purpose.
• Try different detergent.
• Contact the detergent manufacturer.Dull, discoloured or chipped
tableware.• Make sure that only dishwasher-safe items are washed in the appliance.
• Load and unload the basket carefully. Refer to basket loading leaflet.
• Place delicate items in the upper basket.Refer to  "Before first use" , 
"Daily use"  or "Hints and
tips"  for other possible
causes.13.  TECHNICAL INFORMATIONDimensionsWidth / height / depth (mm)596 / 818 - 898 / 555Electrical connection 1)Voltage (V)220 - 240Frequency (Hz)50Water supply pressureMin. / max. bar (MPa)0.5 (0.05) / 8 (0.8)Water supplyCold water or hot water 2)max 60 °CCapacityPlace settings13Power consumptionLeft-on mode (W)5.0Power consumptionOff-mode (W)0.101) 
Refer to the rating plate for other values.
2)  If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the
hot water supply to decrease energy consumption.14.  ENVIRONMENTAL CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and torecycle waste of electrical and electronic
appliances. Do not dispose appliances
marked with the symbol 
 with the
household waste. Return the product to
www.aeg.com20