Home > AEG > Hub > AEG Mixed Hob HD634170NB User Manual

AEG Mixed Hob HD634170NB User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual AEG Mixed Hob HD634170NB User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 513 AEG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							3.The outlet or omnipolar switch used
    for connection is easily accessible
    with the appliance installed.
    The appliance is supplied with a 3 core flexible power cable.
    The wires in the cord are coloured as
    follows:Green and yellow- EarthBlue- NeutralBrown- LiveWARNING!
    A cut off plug inserted into a
    13 amp socket is a serious
    shock hazard. Ensure that
    the cut off plug is disposed
    of safely.8.8  Replacement of the
    connection cableThe replacement of electric
    cable must be carried out
    exclusively by the service
    force centre or by personnel
    with similar competencies, in
    accordance with the current
    regulations.Make sure that the cable
    section is applicable to the
    voltage load and the
    working temperature. The
    yellow/green earth wire (B)
    must be approximately 2 cm
    longer than the live and
    neutral wire (A).
    1. Connect the green and yellow (earth)
    wire to the terminal which is marked
    with the letter 'E', or the earth
    symbol 
    , or coloured green and
    yellow.
    2. Connect the blue (neutral) wire to the
    terminal which is marked with the
    letter 'N' or coloured blue.
    3. Connect the brown (live) wire to the
    terminal which is marked with the
    letter 'L'. It must always be
    connected to the network phase.
    There must be no cut or stray strands
    of wire present. The cord clamp must
    be correctly attached to the outer
    sheath.
    8.9  Attaching the seal
    1.Clean the worktop around the cut
    out area.
    2. Attach the supplied seal stripe to the
    lower edge of the hob along the
    outer edge of the glass ceramic. Do
    not extend it. Make sure that the
    ends of the seal stripe are located in the middle of one side of the hob.
    3. Add some mm when you cut the seal
    stripe to the length.
    4. Push the two ends of seal stripe
    together.
    ENGLISH21   A B   
    						
    							8.10 Assemblywww.aeg.com22min. 450mm
    min.650mm
    min. 2mm
    min. 600 mm  < 20 mm
    min. 2 mm
    A
    B
     A 12 mm28 mm 38 mm  B 57 mm41 mm31 mm
    min  30 mmmin. 500 mm > 20 mm
    min. 2 mm
    A
    B
     A 12 mm28 mm 38 mm  B 57 mm41 mm31 mm
    min. 500 mm R 5mm
    min. 55mm
    490 +1
    mm560 +1
    mm
    600 mm min. 38 mm min. 2 mm  
    						
    							CAUTION!
    Install the appliance only on
    a worktop with a flat surface.8.11  Possibilities for insertionKitchen unit with door
    The panel installed below the hob must
    be easy to remove and let an easy access
    in case a technical assistance
    intervention is necessary.
    A) Removable panel
    B) Space for connectionsKitchen unit with oven
    The electrical connection of the hob and
    the oven must be installed separately for
    safety reasons and to let easy remove
    oven from the unit.
    9.  TECHNICAL INFORMATION9.1  Hob dimensionsWidth590 mmDepth520 mmENGLISH23min. 12 mm min.  2 mm   min 20 mm 
    (max 150 mm)
    60 mm
    B A   
    						
    							9.2 Cooking zones specificationCooking zoneNominal power
    (maximum heat
    setting) [W]Power function
    [W]Power function
    maximum dura-
    tion [min]Cookware diam-
    eter [mm]Left front2300330010180 - 210Left rear140025004125 - 140The power of the cooking zones can be different in some small range from the
    data in the table. It changes with the
    material and dimensions of the
    cookware.For optimal cooking results use
    cookware not larger than the diameter in
    the table.9.3  Bypass diametersBURNERØ BYPASS 1/100 mmRapid52Semi-rapid329.4 Other technical data
    TOTAL POWER:
    Gas original:G20 (2H) 20 mbar = 4,8 kWGas replacement:G30 (3+) 28-30 mbar = 334 g/h
    G31 (3+) 37 mbar = 329 g/hElectric zones:3,7 kWElectric supply:230 V ~ 50 HzAppliance category:II2H3+ Gas connection:R 1/2" Appliance class:3 9.5  Gas burners for NATURAL GAS G20 20 mbarBURNERNORMAL POWER kWMINIMUM POWER
    kWINJECTOR MARK
    1/100 mmRapid2,90,75119Semi-rapid1,90,4596www.aeg.com24 
    						
    							9.6 Gas burners for LPG G30/G31 28-30/37 mbarBURNERNORMAL
    POWER kWMINIMUM
    POWER kWINJECTOR
    MARK 1/100
    mmNOMINAL GAS FLOW g/hG30 28-30
    mbarG31 37 mbarRapid2,70,7586196193Semi-rapid1,90,457113813610.  ENVIRONMENTAL CONCERNSRecycle the materials with the symbol .
    Put the packaging in applicable
    containers to recycle it. Help protect the
    environment and human health and to recycle waste of electrical and electronic
    appliances. Do not dispose appliances
    marked with the symbol 
     with the
    household waste. Return the product to
    your local recycling facility or contact
    your municipal office.
    *
    ENGLISH25   
    						
    							ENGLISH27 
    						
    							www.aeg.com/shop867305018-A-112014    
    						
    All AEG manuals Comments (0)

    Related Manuals for AEG Mixed Hob HD634170NB User Manual