AEG S 80368 Kg User Manual

Hints for storage of frozen food
To obtain the best performance from this appliance, you should:
• make sure that the commercially frozen foodstuffs were adequately stored by the retail-
er;
• be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the
shortest possible time;
• not open the door frequently or leave it open longer than absolutely necessary.
• Once defrosted, food deteriorates rapidly and cannot be refrozen.
• Do not exceed the storage period indicated by the...

It is important to periodically clean the defrost
water drain hole in the middle of the refrigerator
compartment channel to prevent the water over-
flowing and dripping onto the food inside. Use
the special cleaner provided, which you will find
already inserted into the drain hole.
Defrosting the freezer
A certain amount of frost will always form on the freezer shelves and around the top com-
partment.
Defrost the freezer when the frost layer reaches a thickness of about 3-5 mm.
To remove the frost,...

WHAT TO DO IF…
CAUTION!
Before troubleshooting, disconnect the power supply.
Only a qualified electrician or competent person must do the troubleshooting that is not in
this manual.
There are some sounds during normal use (compressor, refrigerant circulation).
ProblemPossible causeSolution
The appliance is noisy.The appliance is not supported
properly.Check if the appliance stands sta-
ble (all the four feet should be on
the floor).
The compressor operates
continually.The Temperature regulator may
be set...

ProblemPossible causeSolution
The temperature in the
appliance is too high.The door is not closed correctly.Refer to Closing the door.
 The product temperature is too
high.Let the product temperature de-
crease to room temperature be-
fore storage.
 Many products are stored at the
same time.Store less products at the same
time.
The temperature in the
refrigeration is too high.There is no cold air circulation in
the appliance.Make sure that there is cold air
circulation in the appliance.
The temperature...

TECHNICAL DATA
   
Dimension  
 Height1850 mm
 Width595 mm
 Depth658 mm
Rising Time 20 h
Voltage 230 - 240 V
Frequency 50 Hz
The technical information are situated in the rating plate on the internal left side of the
appliance and in the energy label.
INSTALLATION
WARNING!
Read the Safety Information carefully for your safety and correct operation of the appli-
ance before installing the appliance.
Positioning
Install this appliance at a location where the ambient temperature corresponds to the cli-
mate...

Location
The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc. Ensure that air can circulate freely
around the back of the cabinet. To ensure best
performance, if the appliance is positioned below
an overhanging wall unit, the minimum distance
between the top of the cabinet and the wall unit
must be at least 100 mm . Ideally, however, the
appliance should not be positioned below over-
hanging wall units. Accurate levelling is ensured
by one or...

3Brown: Live
5Blue: Neutral
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
1. Connect the wire coloured green and yellow to the terminal marked either with the let-
ter “E“ or by the earth symbol 
 or coloured green and yellow.
2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or
coloured black.
3. Connect the wire coloured brown to the terminal...

Levelling
When placing the appliance ensure that it stands
level. This can be achieved by two adjustable feet
at the bottom in front.
Removing the shelf holders
Your appliance is equipped with shelf retainers
that make it possible to secure the shelves during
transportation.
To remove them proceed as follows:
1. Move the shelf holders in the direction of the
arrow (A).
2. Raise the shelf from the rear and push it for-
ward until it is freed (B).
3. Remove the retainers (C).
Door reversibility
WARNING!...

1. Open the doors. Unscrew the middle
hinge (m2). Remove the plastic spacer
(m1).
2. Remove the spacer (m6) and move to
the other side of the hinge pivot (m5).
3. Remove the doors.
4. Remove the left-hand cover pin of the
middle hinge (m3,m4) and move to the
other side.
5. Fit the pin of the middle hinge (m5) into
the left-hand hole of the lower door.
6. Remove using a tool the cover (b1). Un-
screw the lower hinge pivot (b2) and the
spacer (b3) and place them on the op-
posite side.
7. Re-insert the...

10. Install the handle in the opposite side.
Re-screw the handle bracket on the
door (h4). Turn the handle bracket with
the handle and screw them to the door
(h5) and the fitted handle bracket (h6).
11. Re-insert the lower door on the lower
hinge pivot (b2).
12. Insert the middle hinge (m2) into the
left drill of the lower door.
13. Unscrew the upper hinge pivot (t1) and
place it on the opposite side.
14. Fit the upper door on the upper door
pivot.
15. Re-insert the upper door on the middle
hinge pivot...