AGFA AP DC1033m User Manual

							AgfaPhoto DC-1033m   
 
36 
Recording a Voice Memo 
You can add a voice memo to the still images after you record it. 
   
Turn the power on, and set the 
camera to the PLAYBACK mode 
(
page 13). 
   
Press 
 or   to select a still 
image that you want to add a voice 
memo to. 
y  If the image already has the 
voice memo recorded, the 
 
appears on the LCD monitor. 
The new recording will replace 
the previous one.  
   
Open the PLAYBACK menu. 
y Press the MENU button, using four-way control to select Voice Memo (
) 
and press the SET button. 
   
Press the SET button to start recording for 30 seconds. 
y Press the SET button again to end recording. 
 
 
y  The voice memo cannot be added to a movie clip or a protected image. 
y  You cannot delete only the voice memo. When you delete the image, the 
attached voice memo is also deleted. 
Playing Back a Voice Memo 
   
Turn the power on, and set the camera to the PLAY mode (
page 13). 
    
Press 
 or   to select the image that has the voice memo recorded. 
   
Start playing back. 
y Press 
  to start playing the voice memo. 
y Press 
  to stop the voice memo, or press   to pause it. When voice 
memo paused, press 
  again to resume. 
3 
1 
2 
4 
 C C
a a
u u
t t
i i
o o
n n
   
3 
2 
1  
						

							AgfaPhoto DC-1033m   
 
37 
Other Recording Functions 
Setting the Metering 
There are 3 different light metering options available on your camera. 
 
Option Description 
 Light is measured from the entire shooting screen, but gives 
more importance to the values near the center. 
 Selects an exposure based on readings from multiple points in 
the subject area. 
 Selects an exposure based on a single reading taken from the 
center of your picture. 
Setting the White Balance 
Adjust the white balance to match different light sources such as sunlight, incandescent 
(tungsten) lighting or, fluorescent lighting. 
 
Option Description 
 Automatically corrects white balance.    Ideal for general 
photography. 
 Adjusts for bright sun conditions, or natural light conditions. 
 Adjusts for cloudy days or twilight conditions. 
 Adjusts for normal indoor lighting conditions. Corrects the 
orange hue of household light bulbs. Ideal for indoor photos 
under tungsten or halogen lighting without a flash. 
 
 Adjusts for fluorescent lighting. Corrects the green hue of 
fluorescent lighting. Ideal for indoor photos under fluorescent 
lighting without a flash. 
 For more accurate adjustment or when the light source cannot 
be specified. 
 
 
y  Point the camera at a white piece of paper or similar object under the lighting 
conditions for which you want to set the white balance, and then press the 
Shutter button. 
 T T
i i
p p
s s
    
						

							AgfaPhoto DC-1033m   
 
38 
Setting the ISO 
With the initial settings, the ISO sensitivity is automatically set according to the 
brightness of the subject. 
 
Option Description 
Auto  Sets the ISO sensitivity automatically. 
ISO 100  Sets the sensitivity to ISO 100 equivalent. 
ISO 200  Sets the sensitivity to ISO 200 equivalent. 
ISO 400  Sets the sensitivity to ISO 400 equivalent. 
ISO 800  Sets the sensitivity to ISO 800 equivalent. 
ISO 1600  Sets the sensitivity to ISO 1600 equivalent. 
ISO 3200  Sets the sensitivity to ISO 3200 equivalent. (3M in only) 
 
 
y  Higher ISO speeds increase the image noise. To take clean images, use as low 
an ISO speed as possible. 
 
Setting the Exposure 
Set the exposure value manually to compensate for unusual lighting conditions such as 
indirect indoor lighting, dark backgrounds, and strong backlighting. 
 
Setting the AEB 
Sets the auto exposure bracketing (AEB) to shoot 3 continuous images, each with a 
different exposure setting: correctly exposed, underexposed, and overexposed. 
 
Setting the Highlight 
Make the subject stand out from its surroundings. The subject will be in focus in three 
different ranges: 
 /  /  
 
 
y  The Photo Frame and Face Tracking cannot be used as using the Highlight. 
 T T
i i
p p
s s
   
 T T
i i
p p
s s
    
						

							AgfaPhoto DC-1033m   
 
39 
Setting the Sharpness 
You can select whether you want the image to have sharp or soft outlines. 
 
Option Description 
 The edges of the image are emphasized. The edges will 
become sharp, but noise may occur in the recording image. 
 The edges of the image are sharp. This is suitable for printing. 
 The edges of the image are softened. This is suitable for editing 
images on PC. 
 
Setting the Photo Edit 
You can add special effects to your images in Record mode or in Playback mode. 
 
Option Description 
Off  No effect is added to the image. 
 
Red eye removal. (Playback only) 
B&W  Convert image to black & white. 
Sepia  Recorded image will be stored in a sepia tone. 
Negative  Opposite what they were in the original image. 
Mosaic  Add mosaic tiles to the images. (Playback only) 
Red  The image becomes reddish. 
Green  The image becomes greenish. 
Blue  The image becomes bluish. 
Setting Date Stamp 
The Date Stamp function can be used to add a date to your pictures as you take them. 
 
Option Description 
Off  Do not add the recorded date & time to printed images. 
Date  Only add the recorded date to printed images. 
Date & Time  Add the recorded date & time to printed images.  
						

							AgfaPhoto DC-1033m   
 
40 
Setting Stabilizer 
When using higher sensitivity and faster shutter speed settings this function helps 
prevent image blur; caused by hand shake or target movement. This function allows 
good pictures to be taken with little effort. 
 
Setting Face tracking 
After initializing the face tracking function, the lens will lock the main character in the 
picture and follow their movements. Also, the use of auto digital zoom technology allows 
the lens to extend and retract. 
 
 
y  Pressing the shutter halfway showing green AF area means focus is complete. 
y  Face tracking is powered by Arcsoft. 
y  Under some environmental influences, face tracking function may be limited.   
y 
The Highlight and Photo Frame cannot be used as using the Face Tracking. 
 
Setting Photo Frame 
  You can add 10 kinds of frames to still images, making them more interesting. 
 
 
y  This feature is only available with still images (except 3:2 and 16:9). 
y  The Highlight and Face Tracking cannot be used when using the Photo Frame. 
 
 
 
 
 
 
 
 
 
 
 T T
i i
p p
s s
   
 T T
i i
p p
s s
    
						

							AgfaPhoto DC-1033m   
 
41 
Playback 
Playing Back Images 
   
Turn the power on, and set 
the camera to the PLAYBACK 
mode (
page 13). 
y  The latest recorded image 
appears on the LCD 
monitor. 
y  If there are no images 
stored, a message [No 
image] appears. 
  
 
Press the four-way control 
 or  (n). 
y 
: displays the previous image. 
y 
: displays the next image. 
 
  
y Holding down 
 or   scrolls images in a high speed. 
Playing Back Movie Clips 
   
Turn the power on, and set the camera to the PLAYBACK mode   
(
page 13). 
    
Press 
 or   to select a movie clip that you want to playback. 
   
Start playing back. 
y Press 
  to start playing the movie clip. 
y Press 
  to stop the movie clip, or press   to pause it. When the movie 
paused, press 
  again to resume. 
 
 
y  During movie playing back, press 
  to fast forward or press   to rewind it. 
y  Press the shutter to capture the still image from the movie clip while it had paused.
3 
2 
1 
 T T
i i
p p
s s
   
1 
2 
 T T
i i
p p
s s
    
						

							AgfaPhoto DC-1033m   
 
42 
Magnifying & Trimming Still Images 
   
Turn the power on, and set the 
camera to the PLAYBACK 
mode (
page 13). 
   
Select an image. 
y Press 
 or  (p) to select 
the image that you want to 
magnify or trimming. 
y  Only still images can be 
magnified and trimmed.  
    
Magnify the image. 
y Press [T] (n) to magnify the image, and the central portion of the image is 
displayed. You can use the arrow button (p) to view different parts of the 
magnified image. 
 
y Press the MENU button (o) to return to the normal size. 
   
Trim the image. 
y Press the SET button (p) to set the image trimming. 
    
Save the image. 
y Press the SET button (p) again to trim the selected image and save it as a 
new one. 
 
 
 
 
 
 
 
 
 
 
 
 
 
3 
5 
4 
1 
2  
						

							AgfaPhoto DC-1033m   
 
43 
Viewing in Thumbnail 
   
Turn the power on, and set the 
camera to the PLAYBACK mode 
(
page 13). 
   
Press the zoom button [W], a 
thumbnail screen is displayed.  
   
Use the four-way control to select the desired image, and press [T] or the 
SET button to show the selected image in full screen.  
 
 
y  You can protect or delete multiple images in thumbnail, see page 45, 47. 
 
Playing a Slide Show 
   
Turn the power on, and set the 
camera to the PLAYBACK mode 
(
page 13). 
   
Enter the slide show. 
y Press the MENU button (n), 
use the four-way control (o) to 
select Slide Show (
) and 
press the SET button (o). 
  
 
Change the slide show settings. 
y  Use the four-way control (o) to set the slideshow interval (
), effect () 
and repeat (
). 
y  You can set the interval between 1~10 seconds. 
   
Playing the slide show. 
y Press the SET button (o) to start the slideshow. 
y  During the slideshow, press the SET button (o) to pause the slideshow and 
press the SET button again to resume. 
3 
1 
2 
4 
 T T
i i
p p
s s
   
1 
2 
3  
						

							AgfaPhoto DC-1033m   
 
44 
Deleting Files 
Deleting a Single File 
   
Turn the power on, and set the 
camera to the PLAYBACK mode 
(
page 13). 
   
Open the menu. 
y Press the MENU button (n), 
then use the four-way control 
(o) to select Delete (
) and 
press the SET button (o).  
 
   
Press 
 or (o) to select [SINGLE], and then press the SET button (o). 
   
Press 
 or  (o) to select the image you want to delete. 
   
Press the SET button (o) to delete the image. 
y  Repeat step 4~5 to delete images. 
 
 
 
 
 
 
 
 
 
 
 
 
y  To quickly delete the current display image 
1.  Select the image you want to delete. 
2. Press the Delete button (p) to show a confirmation. 
3. Press the SET button (o) to delete the current display image. 
y  Protected images cannot be deleted with this function. 
1 
2 
3 
4 
5 
 T T
i i
p p
s s
    
						

							AgfaPhoto DC-1033m   
 
45 
Deleting Multiple Files 
   
Turn the power on, and set the camera 
to the thumbnail screen (
page 43).
   
Open the menu. 
y Press the MENU button, then Press 
 or   to select to select Delete 
(
) and press the SET button.  
   
Press 
 or   to select [Select], and then press the SET button. 
y  The frame of the selected image turns green. 
   
Select multiple images. 
y  Use the four-way control to select the image. 
y Press the SET button toggles the 
  on and off. Repeat this step until all 
images that you want to delete are displayed with an icon
. 
   
Delete images. 
y Press the MENU button, then select [Yes] and press the SET button. All 
selected images will be deleted. 
y  To cancel delete, press the MENU button in this step. 
Deleting All Files 
   
Turn the power on, and set the camera 
to the PLAYBACK mode (
page 13). 
   
Open the menu. 
y Press the MENU button, then use the 
four-way control to select Delete 
(
  ) and press the SET button.  
 y  You can open the menu in full screen or in thumbnail. 
   
Press 
 or   to select [ALL], and then press the SET button. 
   
Press the SET button to delete all unprotected images. 
 3 
1 
2 
4 
1 
2 
3 
4 
5