Home > Aimco Brakes > AcraDyne > Aimco Brakes AcraDyne ErgoArms Operations Manual

Aimco Brakes AcraDyne ErgoArms Operations Manual

Download as PDF Print this page Share this page

Have a look at the manual Aimco Brakes AcraDyne ErgoArms Operations Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

$Page 1 PO Box 1\f4\f0, Portland OR 97\b9\b-04\f0 • 800-85\b-13\f8 • Fax 800-58\b-9015www.aimco-global.com ERGO-ARM Tool Support Systems Operations Manual MODELS AD-D1098S/SAC& AD-D1098P/PAC Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd \f/\b/2013\: \f:46 AM Page 1$

$Page 2 I N T R O D U C T I O N 2 CAUTION! Please read the following manual before assembling and operating your ErgoArm Tool Support System\b As in all cases, when electric or air lines come in close contact with moving parts or mechanisms, precautions should be taken by the person installing and operating the equipment that these cords or hoses do not become entangled or damaged by moving parts\b Proper attention will prevent possible hazard or injury. R E C O M M E N D E D T O O L S \b...$

$Page 3 3 I N S T A L L A T I O N A N D S E T U P I N S T U C T I O N S - A L L M O D E L S 1.Remove the TABLE MOUNT from the box\b \b. Bolt to work surface\b It is important to level the table mount so that the post is 90 degrees to the work surface through full range of travel (see VIEW #1) 3. Insert POSTinto mount, and tighten set screws\b 4. Remove remaining body of ErgoArm from box and slide ADJUSTABLE SHOULDER CLAMPover POST\b Tighten screws at desired height (see VIEW...$

$Page 4 4 I N S T A L L A T I O N A N D S E T U P I N S T U C T I O N S - A L L M O D E L S The VERTICAL ADJUSTMENT ROD (Item #41) allows the tool to be adjusted from zero degrees (parallel to column), up to 15 degrees in either direction from zero point\b This compensates for any irregularities in the workpiece or if application requires fastener to be driven in at an angle (see View #3)\b This does not take the place of properly leveling the Table Mount Flange\b Use for ﬁnal 90 degree...$

$Page 5 \b I N S T A L L A T I O N A N D S E T U P I N S T U C T I O N S - A L L M O D E L S To increase the reach capability of the ErgoArm, remove the ring pin (Item #14) from the CYLINDER MOUNTING YOKEROD END (Item #1\f)\b Pull the FOREARM INSERT (Item #13) out, away from the arm, the desired reach, up to an additional 5\b Once desired reach is achieved, align holes in FOREARMand FOREARM INSERT, reinsert ring pin in CYLINDER MOUNTING YOKEROD END (Item...$

$Page 6 6 PAR TS B R EAK DO W N Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd \f/\b/2013\: \f:46 AM Page 6$

$Page 7 7 P A R T S B R E A K D O W N Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd \f/\b/2013\: \f:46 AM Page 7$

$Page 8 E R G O - A R M B R E A K D O W N Index PartNu\fber Nu\fberDes\briptionQty 1 EA14Table Flange1 2 EA01 Post1 \f EA02 Shoulder Clamp1 4 EA44 1\b420 x 11\b4 Cap Screw 2 5 EA0\f Bearing4 6 EA04 1\b21\f x 4 Double Ended Stud 2 7 EA05 1\b21\f Locking Nut 2 8 EA21 Label2 9 EA06 Upper Arm 1 10 EA07 Elbow1 11 EA10 Forearm1 12 EA09 Cyl. Mtg. Yoke Rod End 1 1\f EA11 Forearm Insert1 14 EA18 1\b4 x 15\b8 Cotterless Clevis Pin 1 15 EA17 \f\b16 x \f\b4 Clevis Pin 1 16 EA1\f Hair Pin Cotter1 17 EA20 8\f2 x...$

View all the pages

Add page 11 to Favourites

image text

Enable zoom

							      Corporate Headquarters 
10000 SE Pine Street  Ave. Cristóbal Colon 14529 
Portland, OR  97216  Chihuahua, Chihuahua.  31125 
800- 852-1368 Mexico 
FAX 800- 582-9015 011-52-(614) 380-1010
www.aimco-global.com FAX 011-52-(614) 380- 1019 LIT-MAN924  Rev. 
3/2016  Printed in USA  ©2016 AIMCO

All Aimco Brakes manuals Comments (0)

Aimco Brakes AcraDyne ErgoArms Operations Manual

Related Manuals for Aimco Brakes AcraDyne ErgoArms Operations Manual