Aimco Brakes Monitor UEC4800TP Instruction Manual

 & 
WAVE DATA CNTNT SLCT (Wave data content output select) 
Default: 1 
Setting: 0   Not output 
Setting: 1   Output 
Setting: 2   Output when NOK 
]Function^ 
This is to determine whether output or not waveform data to UEC-4800 setup software.    This will 
not sent to the RS232C port on the back panel.   


ANG DATA TRANSM SLCT (Fastening angle output select (former name: MODE 65) 
Default: 1 
Setting: 0      Not output (“0000” to be transmitted) 
Setting: 1   Output (4 bytes) 
]Function^...

 &  
LAN setting 
This is to set up for Ethernet connection.     
Set up the value in LAN SETTING screen, and a message [LAN SETTING] appears.    It takes approx. 
20 seconds after you change setting values and a message [LAN SETTING] goes off from a screen.   
Please do not touch 
.

LAN setting screen consists of three pages.   

First screen (1/3)












IP ADDRESS 1 - 4 
Default: 120.0.100.1 
Setting range: 0 - 255 
CThis is to determine the IP address of UEC....

 & 
Second screen (2/3)












TCP PORT 
Default: 2101 
Setting range: 0 - 9999 
CThis is to set up the TCP port of UEC.     
 
 
CONNECT MODE (Connection mode)   
Default: 1 
Setting: 0 Set UEC as host 
Setting: 1 Set UEC as client   
CSet [1] (UEC as client), when connecting to the UEC-4800 setup software.         
 
 
HOST IP address 1 - 4 
Default: 120.0.100.0 
Setting range: 0 - 255 
This is to set up the IP address of PC which communicates with UEC through Ethernet....

 & 
Third screen (3/3)












LAN RETRY NUM. (LAN retry number)   
Default: 3 
Setting range: 0 - 10 
CThis is to determine the retry number to be made.   
 
 
Comm.-less time (LAN nonresponding limit time) 
Default: 10 
Setting range: 0 - 10 
CThis is to determine waiting time in case of nonresponding.   
 
 
MAC ADDRESS   
Default: Assign unique address   
Setting range: 0 - 9999 
CMac address of UEC.   
CImpossible to change the setting value.   

 &#  
Program Number Change 
 
This is to set the program number choice.    Maximum 8 kinds (fastening torque, judgment values of 
torque and angle etc.) of program can be set up per work.  It is possible to set up maximum 20 
fasteners under same work number.    8 kinds of work number (from program 1 to 8) can be set up for 
first fastener up to 20th fastener.    This function is available with the V1.15 UEC-4800TP or later.    
 
 
 
 
 
 
PRG. CHANGE SLCT (Program change select) 
Default: 0...

 &&  
PRG. CHANGE SWIT (Program change switch) 
Default: 0 
Setting: 0 Switch to next work number only when UEC provides fastening OK. 
Setting: 1 Switch to next work number whichever UEC provides fastening OK/NOK.     
Setting: 2 Switch to next work number when UEC provides OK or torque HIGH NOK.     
]Function^ 
CThis is to determine the condition to have UEC switched to next work number when program 
number choice is used.       
 
 
First – 20th Fastener 
Default: 0 
Setting range: 0 - 8 
Setting: 0...

 & 
11Memory Data 
This is to set up the setting of memory data related items and display memory data like average, , 
original data etc.   
(1)  Touch 
 in the measuring screen to enter MENU screen.   
(2)  Touch 
to move to MEMORY DATA screen.    Menu of MEMORY DATA is 
displayed.    Select the screen you want to set up or change the setting values.   











Memory data screen consists of following five pages.   
]SETUP OF MEMORY^ 
Set up for the contents of memory 
]STATISTICS...

 & 
MEMORY DATA BLOCK (former name: MODE 87) 
Default: 3 
Setting :  1  UEC stores data of work number all in one without time/date and ID number.   
(Maximum 12,000 pcs.) 
 
Setting :  2  UEC stores data per work number without time/date nor ID number.         
(Maximum 1,500 pcs.) 
 
Setting :  3  UEC stores data of work number all in one including time/date, but without ID number.     
(Maximum 5,400 pcs.)   
 
Setting :  4  UEC stores data per work number including time/date, but without ID number....

 & 
 
Statistics Data 








UEC calculates the memorized data and displays [N] (number of data) of fastening data, average 
value, [] (standard deviation), 3/Average value (scatter), [CP] (process capability index), [CPK] 
(unilateral process capability index) and [RANGE] (torque low limit – torque high limit).     
When either 2 or 4 are set to MEMORY DATA BLOCK, UEC displays the data per work number 1 – 
8. When either 1 or 3 is set to MEMORY DATA BLOCK, UEC displays all data in WORK...

 &% 
Former data (raw data) 
 
 
 
 
 
 
 
 



UEC displays memorized data of Torque, Pulse number, fastening time and judgment.  Maximum 
data which can be displayed on 1 page is 10 pieces.    Touch 
 or  to have another 10 data scrolled 
up or down.   
When either 2 or 4 are set to MEMORY DATA BLOCK, fastening data is displayed per work number.   
Touch 
 in right upper of a screen, and work number is changed to other like 1  2 with data 
display of each work number.    When either 1 or 3...