Air Live Router WLA-5200AP User Manual

							
 
Virtual Server 
 Define virtual server ip address and port range, Protocol 
and check the box to enable virtual server, 
The Virtual server which using single port number can be 
accelerated by hardware at wirespeed 
Special 
Application 
 You can define special application that can allow outside users to 
access your internal application behi nd this AP, like QuickTime ,MSN 
gaming zone… 
DMZ 
 DMZ settings will not be worked until WAN have connected 
                                                                       36                                         WLA-5200AP v2 User’s Manual  
						

							
 
Remote 
Mangement 
 You can enable the Remote management function and define 
the port number let can be managed from internet . 
 
 
WISP + Universal Repeater Mode Setting 
 
 
 
 
                                                                       37                                        WLA-5200AP v2 User’s Manual  
						

							
 
                                                                       38                                        WLA-5200AP v2 User’s Manual 
Alias Name You can set the alias name for this device (not exceeding 32 
characters). 
… Disable 
Wireless 
LAN 
Interface Check the box to disable the Wireless LAN Interface, by so doing, 
you won’t be able to make wireless connection with this Access 
Point in the network you are located.  In other words, this device will 
not be visible by any wireless station. 
Band You can choose one mode of the following you need.    
• 11b/g mixed: Select to allow both  wireless-b and wireless-g devices on the 
network. 
• 11B only: Select to allow only wireless-B devices on the network. 
• 11G only: Select to allow only  wireless-G devices on the network. 
• 11A (indoor): Select to allow only wireless-A devices on the indoor 
network. 
• 11A (outdoor): Select to allow only wireless-G devices on the network. 
• 11A (indoor): Select to allow only wireless-A devices on the outdoor 
network
. 
AP SSID The SSID differentiates one WLAN from another; therefore, all 
access points and all devices attempting to connect to a specific 
WLAN must use the same SSID. It  is case-sensitive and must not 
exceed 32 characters. A device will  not be permitted to join the BSS 
unless it can provide the unique SSID. An SSID is also referred to 
as a network name because essentially  it is a name that identifies a 
wireless network 
WISP SSID The SSID differentiates one WLAN from another; therefore, all 
access points and all devices attempting to connect to a specific 
WLAN must use the same SSID. It  is case-sensitive and must not 
exceed 32 characters. A device will  not be permitted to join the BSS 
unless it can provide the unique SSID. An SSID is also referred to 
as a network name because essentially  it is a name that identifies a 
wireless network 
Channel 
Number The number of channels supported depends on the region of this 
Access Point. All stations communicating with the 
Access Point 
must use the same channel. 
SSID of 
extended 
Interface 
When in Universal Repeater mode , you have to enter the ESSID of 
other’s AP/Router that device want to connect. 
The device SSID and the SSID of  extended interface can be the 
same or different. When you are using the universal repeater mode, 
please make sure the remote AP/Router WDS function is turned off.  
						

							
 
Site Survey 
 Click site survey setup button that will shows the WISP Outdoor AP 
list and you can select  which WISP AP you want to connect . 
Please refer the AP mode settings Æ Security for details, 
This setting used Wireless client or remote AP to link this device. 
Security 
Please refer the AP mode settings Æ Advance Setting for details. Advance 
Setting  
                                                                       39                                         WLA-5200AP v2 User’s Manual 
Access 
Control Please refer the AP mode setting Æ Access Control for details. 
WAN Port 
 You can choose the different WAN mode , like   Static IP, 
DHCP,PPPOE,PPTP or L2TP method. 
Virtual 
Server Define virtual 
server ip address 
and port range, 
Protocol 
and check the 
box to enable 
virtual server, 
The Virtual server 
which using 
single port 
number can be 
accelerated by 
hardware at wire-
speed.  
						

							
 
Special 
Application 
 You can define special application that can allow outside users to 
access your internal application behind this AP, like 
QuickTime ,MSN gaming zone… 
DMZ 
                                                                       40                                        WLA-5200AP v2 User’s Manual 
 DMZ settings will not be worked until WAN have connected 
Remote 
Mangement 
  
You can enable the Remote management function and define the 
port  
number let can be managed from internet  
 
  
						

							
 
TCP/IP 
Basic 
In this page, you can change the TCP/IP settings of this Access Point, select to 
enable/disable the DHCP Client, 802.1d S panning Tree, and Clone MAC Address.  
  
This field can be modified only when DHCP Client is 
disabled. If your system manager assigned you static 
IP settings, then you will have to enter the information 
provided. IP Address  
Enter the information provided by your system 
manager. Subnet Mask 
Enter the information provided by your system 
manager.  Default Gateway 
Enter the Domain Name Service IP address. DNS 
Select Disable , Client  or Server from the pull-down 
menu. 
Disable:  Select to disable DHCP server function.  
Client: Select to automatically get the LAN port IP 
address from ISP (For ADSL/Cable Modem). 
Server:  Select to enable DHCP server function.  
DHCP 
DHCP Client 
Range 253 IP addresses continuing from 192.168.1.1 to 
192.168.1.253 
Click to show Active DHCP Client table. Show Client 
Clone MAC 
Address You can specify the MAC address of your 
Access Point to replace the factory setting. 
 
 
                                                                       41                                         WLA-5200AP v2 User’s Manual  
						

							
 
Press to save the new settings on the screen.   Apply Changes 
Press to discard the data you have entered since last 
time you press Apply Change.  Reset 
  
 
Other 
Upgrade Firmware 
 
1.  Download the latest firmware from your distributor and save the file on the hard drive. 
2.  Start the browser, open the  configuration page, click on Other, and click 
Upgrade Firmware to enter the  Upgrade Firmware window. Enter the 
new firmware’s path and file name (i.e. C:\FIRMWARE\firmware.bin). Or, 
click the  Browse button, find and open the firmware file (the browser will 
display to correct file path). 
3. Click  Update to start the upgrade. 
 
Backup/Restore Settings 
 
                                                                       42                                         WLA-5200AP v2 User’s Manual  
						

							
 
 
This function enables users to save the current configurations as a file (i.e. 
config.bin) To load configuration from a f ile, enter the file name or click 
Browse…  to find the file from your computer.anc click update button . 
 
 
 
Factory Default : Click to restore the default configuration. 
 
System Restart  Click to restart the device.  
 
Region Settings 
 You can select your country region  :  Europe, America, South America 
 
Note !!  Select the Country Region will affe ct the each Channel number of each 
Wireless mode. 
 
Password 
For secure reason, it is recommended that  you set the account to access the web 
server of this Access Point. Leaving the user name and password blank will 
disable the protection. The login scr een prompts immediately once you finish 
setting the account and password.  Remember your user name and password for 
you will be asked to enter them every time  you access the web server of this 
Access Point.  
 
                                                                       43                                         WLA-5200AP v2 User’s Manual  
						

							
 
   
Set your new User name. User name can be up to 
15 characters long. User name can contain letter, 
number and space. It is case sensitive. User Name 
Set your new password. Password can be up to 15 
characters long. Password can contain letter, 
number and space. It is case sensitive. Password 
Re-enter the new password for confirmation.  Confirm Password  
Press to save the new settings on the screen.   Apply 
System Log 
This page display log events with time when events happened, log events’ types, 
log sources and the description for events themselves. System manager can use 
the system log to trac e when problems occur.  
Check to enable the system log function and then click  Apply to save your 
configuration. 
  
                                                                       44                                         WLA-5200AP v2 User’s Manual