AL-KO 4x4 Stabiliser Handle User Manual

							INTRODUCTION
1  These instructions are for use of the 4x4 handle only. They
  should be read in conjunction with the Assembly & Operating 
Instructions, which was supplied with your stabiliser. If you 
do not have a copy, please request one from our Service 
Department or download it from www.al-ko.co.uk.
2 When not in use (during travelling or storage), the handle 
MUST be removed from the stabiliser and stored within your 
vehicle. Providing the stabiliser has been coupled correctly, 
the removal of the handle from the stabiliser arms will not 
interfere with the normal operation of the stabiliser. 
3 Only suitable for the AKS 2004/3004 Stabiliser as shown in Fig 1.
 
WARNING
THE 4X4 HANDLE GRIPS ON TO THE LEVER ARMS BY MEANS 
OF SPRING LOADED BALL BEARINGS INSIDE THE HANDLE. 
THIS HANDLE IS NOT DESIGNED TO BE PERMANENTLY FIXED 
TO THE LEVER ARMS OF THE STABILISER. 
FAILURE TO REMOVE THE HANDLE WHILST TRAVELLING 
COULD RESULT IN A SAFETY HAZARD TO OTHER ROAD USERS. 
IT COULD ALSO BECOME AN OBJECT LIABLE TO THEFT.
KIT CONTENTS
1 Replacement handle
2 Torx spanner
Fig 1 AL-KO Security Device
Fig 1 AL-KO Security DeviceFig 1 AL-KO Security Device
OPERATING INSTRUCTIONS FOR 
AL-KO 4X4 REPLACEMENT STABILISER HANDLE
ASSEMBLY
1 Remove the existing stabiliser handle: Using the torx 
spanner provided, undo and remove the fixing screw located 
on the side of the red handle. The red handle should now pull 
off the stabiliser lever arms. 
2 To fit: Ensure both stabiliser lever arms are level and using 
gentle force, push the 4x4 handle on to the lever arms. 
3 To remove: Use gentle force, grip the handle firmly and pull 
the handle backwards and away from the lever arms.
 
						

							AL-KO Kober Ltd, South Warwickshire Business Park, Kineton Road, Southam, Warwickshire, CV47 OALE-Mail: [email protected] www.AL-KO.co.uk Tel: 01926 818500
Due to a policy of continuous improvement, AL-KO reserves the right to change technical specifications.  Part No. 1389609 Iss. 3 07/12
OPERATING INSTRUCTIONS FOR 
AL-KO 4X4 REPLACEMENT STABILISER HANDLE
COUPLING UP USING 4X4 HANDLE
1 With the 4x4 handle in place, raise the stabiliser lever arms to 
45º and remove the handle from the stabiliser (Fig 3).
2 With the 4x4 handle removed, push the stabiliser lever arms 
into the upright position and raise the coupling handle (Fig 4). 
3 Couple up to the towball as normal.
4 With the stabiliser now coupled up, pull the arms down to 
45º and reattach the 4x4 handle before pushing the stabiliser 
arms down fully, locking the friction pads onto the towball. 
5 Remove 4x4 handle from stabiliser and store in tow vehicle. 
UNCOUPLING USING 4X4 HANDLE
1 Reattach the 4x4 handle to the stabiliser lever arms (Fig 5). 
2 With the 4x4 handle in place, raise the stabiliser arms 45º to 
disengage the friction pads from the towball (Fig 6).
3 Remove the 4x4 handle (Fig 3). 
4 With the 4x4 handle removed push the stabiliser arms to 90º 
and uncouple from the towball as normal (Fig 4).
Fig 4 Handle removed, arms at 90º
Fig 6 Raise stabiliser arms to 45ºFig 5 Slide handle over stabiliser arms
Fig 3 Slide handle off the stabiliser arms



