Aleratec 111 HDD Copy Cruiser IDESATA 11 HDD Duplicator and 12 HDD Sanitizer User Guide

www.aleratec.com15
Using the 1:11 HDD Copy Cruiser IDE/SATA 
Main Menu
Async Copy
The function “Async Copy” allows you to insert target drives during the copying 
operation. During the process, you can insert another drive as a target of the Async 
Copy operation and the unit will automatically copy to this new drive as well.  
1. Load the source HDD and the target HDDs into the 1:11 HDD Copy Cruiser 
IDE/SATA. The system will auto-detect the hard drives. After the drives have 
been detected, a screen...

www.aleratec.com16
Using the 1:11 HDD Copy Cruiser IDE/SATA 
Main Menu
Compare HDD
The “Compare HDD” function performs a comparison of data from the source hard 
drive to the data on the target hard drives. 
1. With the source and target HDDs loaded use the arrow buttons (or) to 
select “Compare HDD”. The following screen will be displayed. 
2. Press ENT to begin the comparison. The system will auto-detect the hard 
drives.  
During the compare process, the 1:11 HDD Copy Cruiser IDE/SATA will 
display...

www.aleratec.com17
Using the 1:11 HDD Copy Cruiser IDE/SATA  
Main Menu
Async Compare
The function “Async Compare” allows you to insert target drives for data comparing 
during the comparing operation. During the process, you can insert another drive as 
a target of the Async Compare operation and the unit will automatically compare 
this new drive as well. 
1. With the source and target HDDs loaded use the arrow buttons (or) to 
select “Async Compare”. The following screen will be displayed. 
2. Press...

www.aleratec.com18
Using the 1:11 HDD Copy Cruiser IDE/SATA 
Main Menu
PreScan Source
The “PreScan Source” scans the source hard drive to determine if it can be read 
correctly.  
1. With the source HDD loaded, use the arrow buttons (or) to select “PreScan 
Source”. The following screen will be displayed. 
2. Press ENT to begin the scan. The system will auto-detect the hard drives. 
During the PreScan process, the 1:11 HDD Copy Cruiser IDE/SATA will 
display progress information. 
3. When the PreScan...

www.aleratec.com19
Using the 1:11 HDD Copy Cruiser IDE/SATA 
Main Menu
ReScan Bus
The “ReScan Bus” function causes the 1:11 HDD Copy Cruiser IDE/SATA to 
redetect connected hard drives. This can be used when you change drives without 
restarting the system. 
1. Use the arrow buttons (or) to select “ReScan BUS”. The following screen 
will be displayed.  
2. Press ENT to select. The system will prompt you to confirm that you wish to 
proceed.  
3. Press ENT	to begin the rescan, during which the following...

www.aleratec.com20
Using the 1:11 HDD Copy Cruiser IDE/SATA 
Main Menu
Source HDD Size
The “Source size” function is used to display the capacity of the source hard drive. 
1. With the source HDD loaded, use the arrow buttons (or) to select “Source 
size”. The following screen will be displayed.  
2. Press ENT	to display the capacity of the source hard drive. 
ENTESC


7. Source size
ENTESC


Total: 232.5GB  

www.aleratec.com21
Using the 1:11 HDD Copy Cruiser IDE/SATA  
Main Menu
Secure Erase
The “Secure Erase” function will sanitize (wipe clean of all data) the hard disk 
drives connected to the 1:11 HDD Copy Cruiser IDE/SATA using algorithms 
programmed by the hard drive manufacturer.  Since this function is native to the 
hard drive, it is very fast and reliable.  Almost all modern SATA hard drives support 
this feature.  In the rare case that Secure Erase is not supported, please use the 
“Overwrite”...

www.aleratec.com22
 
 
 
5. You can now scroll up and down for the individual status of each drive.  
Using the 1:11 HDD Copy Cruiser IDE/SATA  
 
 
 
 
 
 
 
 
 ENTESC


1 HDD          CH:0Wipe successful  

www.aleratec.com23
Using the 1:11 HDD Copy Cruiser IDE/SATA 
Main Menu
Overwrite
The “Overwrite” function will sanitize (wipe clean of all data) the hard disk drives 
connected to the 1:11 HDD Copy Cruiser IDE/SATA. 
1. Load up to 12 HDDs into the 1:11 HDD Copy Cruiser IDE/SATA. The system 
will auto-detect the hard drives. Using the arrow buttons (or) select 
“Overwrite”. The following screen will be displayed. 
Note: Overwriting the entire capacity of all connected hard drives 
can take an extended...

www.aleratec.com24
Using the 1:11 HDD Copy Cruiser IDE/SATA 
b. To perform a “Three Pass Overwrite”, scroll to “3 Pass” and press ENT. 
This method will write one pass of 1’s, one pass of zeros, and one pass of  
randomly generated data. 
The next screen allows you to choose whether you wish to verify the 
random overwrite. 
Use the arrow buttons to toggle between “On” and “Off”. Press ENT to 
select.
c. To perform a “Seven Pass Overwrite”, scroll to “7 Pass” and press ENT. 
The following screen will be...