Aleratec 122 USB Copy Cruiser Mini USB Flash Drive Duplicator User Guide

							SOFTWARE USER GUIDE
 
Aleratec USB Duplication Suite
 
1:10 USB 3.0 Copy 
Cruiser Mini™
Part No. 330113, 330113EU
1:16 USB 3.0 Copy 
Cruiser Mini™
Part No. 330115, 330115EU
1:22 USB Copy 
Cruiser Mini™
Part No. 330119, 330119AU,       
               330119EU  
						

							www.aleratec.com
Copyright/Model Identification
The content of this manual is for informational purposes only and is subject 
to change without notice. 
This manual is copyrighted with all rights reserved. Under copyright laws, 
this manual and the software described within may not be copied, except in 
the normal use of the product(s) described within or to make a backup copy.
Copyright© 2014
Aleratec, Inc.
9851 Owensmouth Avenue
Chatsworth, CA 91311 U.S.A.
www.aleratec.com
Aleratec is a registered trademark and 1:22 USB Copy Cruiser Mini™, 1:16 
USB 3.0 Copy Cruiser Mini™, and 1:10 USB 3.0 Copy Cruiser Mini™ are 
trademark of Aleratec, Inc.
Check out Aleratec Online!
•	google.com/+AleratecInc
•	YouTube.com/Aleratec
•	Twitter.com/Aleratec
•	Facebook.com/Aleratec
•	Blog.Aleratec.com
 
Please record the following information to help expedite any warranty claim:
Model No.  _____________________Serial No. _____________________
Date Purchased  ________________________________________________ 
Place of Purchase   ______________________________________________  
						

							www.aleratec.com
Table of Contents
Introduction .......................................................................................1
Initial System Setup  ................................................................................1
For Ease of Use .......................................................................................2
Using the USB Duplication Suite Software  ....................................5
Source Tab  ..............................................................................................6
Destination Tab .......................................................................................7
Data Copy Only  ......................................................................................9
Format (FAT, FAT32, NTFS) ................................................................10
Format Then Data Copy (FAT, FAT32, NTFS) .....................................12
Create Image File  ..................................................................................15
Clone Image File ...................................................................................16
Port Training  .........................................................................................17
Technical Support  ..........................................................................19
Technical Support FAX Back Form  ..............................................20  
						

							www.aleratec.com   
						

							www.aleratec.com1
Introduction
Thank you for purchasing an Aleratec USB Duplicator. Please read this 
Software User Guide thoroughly before using this product.
Initial System Setup
1. Connect the USB cable (included) to the USB port on the back of your 
duplicator and to an empty USB port on your computer.
2. Connect the included power cord to the power input on the duplicator 
and into an available power outlet.
3. Insert the Aleratec USB Duplication Suite Installation and Software 
Flash Drive into an available USB port on your computer.
4. Click on Install Aleratec USB Duplication Suite to install the 
duplication software.
5. Follow the on-screen prompts to complete the installation.
6. Press the power button to power up the Aleratec USB Duplicator.
7. The blue power LED will light, and the computer will recognize the 
device.
8. Start the USB Duplication Suite duplication software via the icon  
on your Desktop or in the Start menu under “All Programs.”  
						

							www.aleratec.com2
Introduction
For Ease of Use 
 
To make duplication even easier, we’ve added a feature that lets you match 
up the logical drives shown in the USB Duplication Suite software with the 
actual physical port position of that drive.  To take advantage of this function, 
a “Port Training” needs to be performed to match each USB Port to your 
Aleratec USB Duplicator.  For example, you would likely designate the upper 
port on the duplicator Port 1 and so on (see image).
 
 
 
 
 
 
 
 
 
1:22 USB Copy 
Cruiser Mini™ 
For details please see 
section titled Port Training 
on page 17 in the manual.  
						

							www.aleratec.com3
Introduction
For Ease of Use
1:16 USB 3.0 Copy Cruiser Mini™  
 
 
 
 
 
 
 
 
 
 
         For details please see section  
         titled Port Training on page 17  
         in the manual. 
 
 
   
						

							www.aleratec.com4
Introduction
For Ease of Use
1:10 USB 3.0 Copy Cruiser Mini™ 
 
 
 
 
 
 
 
 
 
 
 
         For details please see section  
         titled Port Training on page 17  
         in the manual.  
						

							www.aleratec.com5
Using the USB Duplication Suite Software
Main Menu
The USB Duplication Suite’s main menu offers eight functions:
1. Data Copy Only
2. Format FAT
3. Format FAT32
4. Format NTFS
5. Format Then Data Copy
6. Create Image File
7. Clone Image File
8. Port Training
 
Choose the desired option from the drop down menu located on the Source tab. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
When using the USB Duplication Suite, ensure that only the USB flash 
drives you wish to operate on are plugged into the duplicator. Remove 
all other media from the computer and duplicator before using the USB 
Duplication Suite.  
						

							www.aleratec.com6
Using the USB Duplication Suite Software
Source Tab
The Source tab has several key functions as listed below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1. Job Selection List: This drop down menu lists all the available 
functions the USB Duplication Suite offers.
2. Add File / Add Folder: Add File/Add Folder buttons allows you to 
select any files / folders you would like to copy. These buttons are 
available for Data Copy Only or Format Then Data Copy job types.
3. Remove / Clear: The Remove button allows you to remove items listed 
in the Add Files box one at a time. The clear button will remove all 
items listed in the Add Files box.
4. Full Format: The Full Format check box allows you to specify whether 
or not the format job being performed is a full format or a quick format. 
Note: quick format is the default setting if Full Format is unchecked.
5. Verify Data: If you wish to verify the Source data files are copied 
successfully, you may click the Verify Data check box when applicable.
3.
4.
5.
2.
1.