Home > Aleratec > Blu-ray Duplicator > Aleratec 17 Bluray DVD CD Tower LightScribe Publisher SLS User Guide

Aleratec 17 Bluray DVD CD Tower LightScribe Publisher SLS User Guide

Here you can view all the pages of manual Aleratec 17 Bluray DVD CD Tower LightScribe Publisher SLS User Guide. The Aleratec manuals for Blu-ray Duplicator are available online for free. You can easily download all the documents as PDF.

Page 41

www.aleratec.com35
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Note: If the number of bl\bank di\bc\b you in\berte\bd doe\bn’t match the\b 
number of di\bc\b dete\bcted on the \bcreen,\b plea\be give 10-15 \b\becond\b 
for the duplicator \bto recognize all of\b your blank di\bc\b.
e. After 2 or 3 seconds of processing time, the following Copy Progress 
Screen will appear.
Note: It i\b normal to \bee\b the progre\b\b indica\btor \btay at 0-10% a\bnd at 
100% for approximat\bely 30 \becond\b durin\bg CD...

Page 42

www.aleratec.com36
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
How to Make Copies \Bfrom the Hard Driv\Be - continued
Next, refill more blank media to continue making more copies, or you can press 
ESC to terminate your project and go back to the main menu.
If you’ve specified a counter value for your project and your project is 
completed, you will see the following screen:
If you see above message, you can press ENT to go back to main menu.
Note: If you enabled the\b counter and the n\bumber of...

Page 43

www.aleratec.com37
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Select B\frn Speed
This process will allow you to adjust the duplication speed subject to your various 
needs.
By default, the duplication speed will be set to the optimal speed. However, 
under some circumstances, you might want to lower the duplication speed.  Those 
circumstances are as follows:
• Poor Blank Media Quality – When your media quality is not good, lowering 
down the duplication speed is necessary to make good copies.
• Poor...

Page 44

www.aleratec.com38
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Select B\frn Speed - continued 
3. Select duplication speed type.
There are different types of recording speeds:
 ▪HDD/BD to BD: Copying to Blu-ray Media from Pre-loaded BD Partition 
or Original BD Media.
 ▪HDD/CD to CD: Copying to CD-R/RW Media from Pre-loaded CD 
Partition or Original CD Media.
 ▪HDD/DVD to DVD: Copying to DVD±R Media from Pre loaded DVD 
Partition or Original DVD Media.
 ▪HDD/DVD-DL to DVD-DL: Copying to Double/Dual...

Page 45

www.aleratec.com39
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Select the So\frce d\Brive
When making a copy, you will need to specify where the master is. Is it in the Source 
drive? Or is it an Image inside the Hard Drive? This tutorial will show you how to 
change the Master Reading Source to satisfy your needs.
Basically, there are 3 scenarios that require you to select the Source drive.
1. Disc-to-Disc copy (Copy from 1st Tray) – This is the case when you would 
normally make copies on the fly....

Page 46

www.aleratec.com40
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Select the So\frce d\Brive - continued 
b. Enter “Source Selection” menu.
Press ENT to enter into “Source Selection” menu.
You will see the following display:
 
Make sure it is located at “Drive 1 Port 0.0”. If not, press the UP or 
DOWN navigation button to search for it. There will be drive model
information where XXXXXX is shown above.
c. Select desired master reading device.
Press the UP or DOWN button to select the desired master...

Page 47

www.aleratec.com41
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Change the SETUP Settings
Most of the internal settings and information are stored inside the “Setup” menu. To 
explore and modify these settings is simple. In the following example you will be 
modifying the “Auto Start” setting. 
Note: The default “Setup\b” i\b \bet for optimal\b performance. It i\b\b unnece\b\bary to 
change thi\b \betting \bif you are \bati\bfied \bwith your duplicato\br performance.
1. Use the UP or DOWN arrow button...

Page 48

www.aleratec.com42
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
A\fdio CD Editing
This procedure will guide you in using the “Mix Audio Tracks” feature. This process 
allows you to combine audio tracks from various CDs into a single customized 
audio CD.
To use this feature you need a temporary storage location to hold your music before 
the duplicator can make it an audio CD. The following are temporary storage 
location choices:
• Hard Drive:
Choosing “Hard Drive” as the temporary storage location,...

Page 49

www.aleratec.com43
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
4. Once you made your selection, you will see the following display:
OR
When you see the above display, insert an audio CD that contains your music 
track(s) in the Master Reading Tray and a blank CD-R media into one of Writer 
Trays.
Note: If either one of t\bhe above \bcreen\b i\b \b\bhown for more than\b 2 
minute\b, plea\be chec\bk your Ma\bter Di\bc o\br Blank Di\bc\b for qu\bality.
Please allow 5-10 seconds for the duplicator to...

Page 50

www.aleratec.com44
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
A\fdio CD Editing - continued 
6. Press ENT button to submit your selection. You will see the following display:
Warning: If the capacity o\bf total audio track\b\b you have \belected\b i\b more 
than your blank CD-\bR di\bc’\b capacity, you will \bee the \bfollowing two 
\bcreen\b fla\bhing:
If you see the above messages, press ENT button to continue.
Once the Copying process is complete, you will see the following display:
7. You now...
Start reading Aleratec 17 Bluray DVD CD Tower LightScribe Publisher SLS User Guide

Related Manuals for Aleratec 17 Bluray DVD CD Tower LightScribe Publisher SLS User Guide

All Aleratec manuals