Alpha Tool.Com.HK Limited Stone Cutter AWS125225 User Manual

11
2.    Check items below when the GFCI goes OFF frequently.
 • Force applied on the stone cutter.
 • Water entered inside the stone cutter.
 • Voltage drop due to sharing the same power source in work area.
 • Worn carbon brushes
BEFORE USE
  DANGER!
Before using the machine, check the following items.  In particular, check items 1 to 5 before 
plugging the power supply cord into the power outlet.
1. Check the working voltage.
–  Be sure the voltage specified on the nameplate is the voltage available...

12
  WARNING!
1. Before turning the switch ON, make sure the rotating parts are not touch\
ing    
anything. If the switch is turned ON while they are in contact with anyt\
hing    
else, the blade may get damaged and it may cause injuries.
2. When a new blade is attached and the switch is turned ON, keep your body\
    
well away from the exposed sides of the tool for a moment until the mach\
ine    
reaches its full speed.
3. It is very dangerous to perform cutting operations using cracked, chipped or...

13
 INSTALLATION OF WATER ATTACHMENT
1.  Remove the wing screw and washer for 
adjusting the cutting depth. 
 (See Figure-6)
2.  Raise cutting depth so there is room 
between the body and the base plate. 
(See Figure-6)
3.  Insert the plastic nozzle on the water-feed assembly behind the height adjustment 
slide. Make sure that the water valve bracket (Part No. 133094) is in \
front of the slide. 
If your blade is already installed, the plastic nozzles should be positi\
oned so that each 
nozzle directs...

14
Spanner Wrench
T-handle Wrench...turn clockwise to loosen
 WATER FLOW   
Connect only to an isolating transformer when using water 
flow.
Connect the nylon hose onto the water valve, then connect 
the adapter on the nylon hose to the water faucet.
Simply adjust the volume of the water flow by turning the 
handle on the water valve.
ADJUSTING CUTTING DEPTH
1. Loosen the wing screw on the depth indicator and move the base plate up or down 
to the desired cutting depth.  Re-tighten the wing screw to a...

15
CURVE CUTTING BLADE INSTALLATION
STRAIGHT BLADE INSTALLATION
 
 
Bolt M6x30 LeftPart No. 133463
Alpha®
 Co\ftour Cur ve Cutt\b\fg Blade Fla\fge 
I
Part No. 13341 8
Fla\fge IIIPart No. 133432
Fla\fge IIPart No. 133419
 
 
Bolt M6x20 LeftPart No. 133464
Flange IIPart No. 133419
Flange IPart No. 13341 8
Al\fha® St\baight Cutting Blad\Ae
Figure-15
Figure-16   

16
  CAUTION!
Allow the saw blade to do the work, applying excessive forward pressure \
to the tool will slow 
down the RPM’s and burn up the motor, which voids the limited warranty of the tool.
This tools should only be used for cutting on a horizontal surface.
Be sure to follow daily maintenance before and after each use.
 
 OPTION 1: FREE-HAND CUTTING
If you are cutting stone or tile less than 20 mm (3/4”) thick, the cut can be done in 
one pass (allow saw blade to do the work).
2. If you are cutting...

17
straight. 
 OPTION 3: USING THE CARRIAGE ASSEMBLY AND GUIDE RAIL
Install the guide rail 2-3/4 inches / 70mm from the intended cut. Take care to ensure that 
the guide rail is properly clamped in place and double check your measur\
ements. Attach 
the carriage assembly to the base plate by aligning the base plate prope\
rly and attaching 
the pressing plates. Make sure that the pressing plates are securely fas\
tened. The AWS 
should be immobile with in the carriage assembly. Slide the carriage onto...

18
 CURVE CUTTING APPLICATION
When cutting the curved line, you can remove the ruler guide and cut fre\
e-hand. (Figure-8) 
Step 1. Score along the cutting line (1/3 width of stone).
Step 2. Step-cut along scored line (2/3 width of stone).
Step  3. Plunge cut all the way to make full contact between bottom plate and sto\
ne, then 
maintain even cutting pressure to follow curved cut line. 
     WARNING!
Support the sink cutout area; sinkhole cutout piece may drop to the floor at the end of cut-
ting...

19
BLADE INSPECTION, INSTALLATION, AND REMOVAL
  DANGER!
Be sure to unplug the power cord from the outlet before attaching or rem\
oving the 
saw blade from the tool.  Accidental starting of the motor may cause bodily injury. 
  WARNING!
Be sure to securely tighten the flange assembly and all loose screws before testing the unit.  
Please allow the saw blade to do the work.  Applying excessive force may damage the saw 
blade and cause premature failure of the bearings and gears.  Such action may decrease...

20
AWS-125 MAINTENANCE
 DAILY
1. Before daily start-up inspect tool, power cord, GFCI, and Saw Blade, loo\
king for chips 
and cracks.
2. If damage has occurred, repair affected areas before use.
3. Connect the tool to the correct power source and test the Ground Fault C\
ircuit Interrupter 
(GFCI) before using the tool.  Push the red RESET button and confirm that the red run 
light is on.  Push the yellow TEST button and confirm that the red run light is off, push 
the red RESET button to use the tool....