Home
>
Alpha Tool.Com.HK Limited
>
Cutting System
>
Alpha Tool.Com.HK Limited Stone Cutter AWS125225 User Manual
Alpha Tool.Com.HK Limited Stone Cutter AWS125225 User Manual
Here you can view all the pages of manual Alpha Tool.Com.HK Limited Stone Cutter AWS125225 User Manual. The Alpha Tool.Com.HK Limited manuals for Cutting System are available online for free. You can easily download all the documents as PDF.
Page 21
![Page 21
21
REPLACING AND CHECKING THE CARBON BRUSHES
In order to keep your tool running correctly, you need to check your carbon brushes after
every one hundred hours (100 hrs) of use. Carbon brushes wear out ove\
r time based on
tool’s usage. If a carbon brush is worn out, it may cause the motor to malfu\
nction or fail
to run. The carbon brushes should be replaced when they are worn down to a quarter of
an inch (1/4”) in size.
DANGER!
Be sure to unplug the power cord from the outlet before assembling...](http://img.usermanuals.tech/thumb/326/5166/w300_stone-cutter-aws125225-user-manual-1478733661_d-20.png "Page 21
21
REPLACING AND CHECKING THE CARBON BRUSHES
In order to keep your tool running correctly, you need to check your carbon brushes after
every one hundred hours (100 hrs) of use. Carbon brushes wear out ove\
r time based on
tool’s usage. If a carbon brush is worn out, it may cause the motor to malfu\
nction or fail
to run. The carbon brushes should be replaced when they are worn down to a quarter of
an inch (1/4”) in size.
DANGER!
Be sure to unplug the power cord from the outlet before assembling...")
21 REPLACING AND CHECKING THE CARBON BRUSHES In order to keep your tool running correctly, you need to check your carbon brushes after every one hundred hours (100 hrs) of use. Carbon brushes wear out ove\ r time based on tool’s usage. If a carbon brush is worn out, it may cause the motor to malfu\ nction or fail to run. The carbon brushes should be replaced when they are worn down to a quarter of an inch (1/4”) in size. DANGER! Be sure to unplug the power cord from the outlet before assembling...
Page 22
![Page 22
22
Proper Alignment
4. Install new carbon brush with the proper alignment of the brush holder f\
ollowed by the
cap as shown in Figure 25.
Figure-25
Old Carbon Brush
worn down to a quarter
of an inch (1/4”).
New Carbon Brush
Figure-24
3. Check the carbon brush for wear. Replace if worn down to a 1/4" or if spring is
damaged.](http://img.usermanuals.tech/thumb/326/5166/w300_stone-cutter-aws125225-user-manual-1478733661_d-21.png "Page 22
22
Proper Alignment
4. Install new carbon brush with the proper alignment of the brush holder f\
ollowed by the
cap as shown in Figure 25.
Figure-25
Old Carbon Brush
worn down to a quarter
of an inch (1/4”).
New Carbon Brush
Figure-24
3. Check the carbon brush for wear. Replace if worn down to a 1/4\" or if spring is
damaged.")
22 Proper Alignment 4. Install new carbon brush with the proper alignment of the brush holder f\ ollowed by the cap as shown in Figure 25. Figure-25 Old Carbon Brush worn down to a quarter of an inch (1/4”). New Carbon Brush Figure-24 3. Check the carbon brush for wear. Replace if worn down to a 1/4" or if spring is damaged.
Page 23
![Page 23
23
Note: If you notice any resistance while tightening the carbon brush cap, it is an indication
that the top plate on the carbon brush assembly is sticking inside the b\
rush cap.
Continuing to tighten will damage the carbon brush spring. (Go to step 6 to correct
this problem)
5. Tighten cap until secure as shown in
Figure 26.
6. Remove the cap and carbon brush from the tool, visually check the two parts for
defects as shown in Figure 27.
Figure-26
Figure-27
Carbon Brush CapTop Plate](http://img.usermanuals.tech/thumb/326/5166/w300_stone-cutter-aws125225-user-manual-1478733661_d-22.png "Page 23
23
Note: If you notice any resistance while tightening the carbon brush cap, it is an indication
that the top plate on the carbon brush assembly is sticking inside the b\
rush cap.
Continuing to tighten will damage the carbon brush spring. (Go to step 6 to correct
this problem)
5. Tighten cap until secure as shown in
Figure 26.
6. Remove the cap and carbon brush from the tool, visually check the two parts for
defects as shown in Figure 27.
Figure-26
Figure-27
Carbon Brush CapTop Plate")
23 Note: If you notice any resistance while tightening the carbon brush cap, it is an indication that the top plate on the carbon brush assembly is sticking inside the b\ rush cap. Continuing to tighten will damage the carbon brush spring. (Go to step 6 to correct this problem) 5. Tighten cap until secure as shown in Figure 26. 6. Remove the cap and carbon brush from the tool, visually check the two parts for defects as shown in Figure 27. Figure-26 Figure-27 Carbon Brush CapTop Plate
Page 24
![Page 24
24
7. Check to see if the two parts move freely by pushing the top plate of th\
e carbon
brush into the recess on the bottom of the carbon brush cap and rotate.
Carbon Brush and Cap
Figure-28
Top Plate
8. If the two parts stick together, replace the carbon brush cap and repeat step 7.
9. If the top plate of the carbon brush sticks in the new cap, you need to \
replace the
carbon brush and repeat step 7.
10. Keep trying until carbon brush top plate can move freely inside of the r\
ecess on the...](http://img.usermanuals.tech/thumb/326/5166/w300_stone-cutter-aws125225-user-manual-1478733661_d-23.png "Page 24
24
7. Check to see if the two parts move freely by pushing the top plate of th\
e carbon
brush into the recess on the bottom of the carbon brush cap and rotate.
Carbon Brush and Cap
Figure-28
Top Plate
8. If the two parts stick together, replace the carbon brush cap and repeat step 7.
9. If the top plate of the carbon brush sticks in the new cap, you need to \
replace the
carbon brush and repeat step 7.
10. Keep trying until carbon brush top plate can move freely inside of the r\
ecess on the...")
24 7. Check to see if the two parts move freely by pushing the top plate of th\ e carbon brush into the recess on the bottom of the carbon brush cap and rotate. Carbon Brush and Cap Figure-28 Top Plate 8. If the two parts stick together, replace the carbon brush cap and repeat step 7. 9. If the top plate of the carbon brush sticks in the new cap, you need to \ replace the carbon brush and repeat step 7. 10. Keep trying until carbon brush top plate can move freely inside of the r\ ecess on the...
Page 25
25 The ideal general purpose blade for use on masonry, concrete and tile. The turbo rim allows for safe and smooth operation. It is cost effective, long lasting and provides consistent results. A valuable addition to your toolbox. Alpha® Eclipse II Alpha® Libero The ultimate blade for cutting marble: The advanced diamond rim is designed to cut softer materials (marble, travertine, soapstone and alabaster) without the chipping and cracking commonly as- sociated with dry cutting. It is aggressive and...
Page 26
26 This is the latest addition to Alpha® Contour curve cutting series blade for Porcelain. Alpha® made this application possible in conjunction with Alpha® AWS-125 Wet Stone Cutter. You can cut sinkhole of 1-1/4” porcelain slab without breaking the rim. Due to the nature of the material, this blade must be used wet only. *Always wear eye protection and proper personal safety equipment when using these products. The Alpha® Vacuum Hold Down System is a clamp- free restraining system utilizing...
Page 27
27
ALPHA® AWS-125 WET STONE CUTTER SCHEMATIC
Page 28
28 ALPHA® AWS-125 WET STONE CUTTER PARTS LIST DRAWING NO.PART NO.DESCRIPTIONQUANTITY 1133080Screw M5×403 2130031Self-tapping Screw St 3.9 X197 3133289/133292GFCI 110V/220V1 4133033Carbon Brush (2 pc set)2 5133031Brush Holder2 6133032Brush Cap2 7133422Rated Plate 110V1 8133047Cable Sleeve1 9130618Block Terminal 2 10133040Wire Terminal2 11133042Insulation Pipe2 12133034Brush Terminal Assembly2 13133436/133004Field Coil 110V/220V1 14133086Cable Clamp1 16133030Air Bridge1 17133025Bearing 608-2RZ1...
Page 29
29 ALPHA® AWS-125 WET STONE CUTTER PARTS LIST DRAWING NO.PART NO.DESCRIPTIONQUANTITY 39133418Flange I (for AWS-125)1 40133062O Ring 18×2.51 41133057Spindle (for AWS-125)1 42133053Ball Bearing 6201-2RS1 43133242Brand Label1 44133416TT Ruler Guide (for AWS-125)1 45133058Gear (Big)1 46133066Needle Bearing Bk 08101 47133255Gear Box1 48133067O Ring 25.5×21 49133084Wing Screw3 50133269Washer For Ruler2 51133085Pin 6x281 52133107Screw M3x51 53133108Lock Washer M31 54133094Water Valve Bracket (for...
Page 30
30
EC DECLARATION OF CONFORMITY
Name of Manufacturer: Alpha Professional Tools®
Address of Manufacturer: 103 Bauer Drive
Oakland, NJ 07436
USA
Herewith declares that:
ELECTRIC HAND TOOL: “Electric Stone Cutter”
Make: Alpha Professional Tools®
Type: AWS-225
-Does comply with the provisions of EMC 2004/108/EC, the Low Voltage Directive
2006/95/EC and Machinery Directive 2006/42/EC .
And furthermore declares that:
-The following (parts/clauses of) harmonized standards have...