Altek Model 22 Step Thermocouple Simulator Manual

							Thermcouple Source
Model 22
• Direct temperature output22 precise steps
• 0.1% accuracy25, 50, or 100 degree resolution
• Rugged designField, shop and control room use
• Pocket sized1 year battery life
• Models for types B, E, J, K, R, S, T°C & °F cold-junction compensatedAltek Model 22 Thermocouple Sources provide 22
precise temperatures for inputs to transmitters,
recorders, controllers, alarms, data acquisition and
computer systems. The Model 22 provides
thermocouple wire output and is cold-junction
compensated for ambient temperature variations.
Conformity to the particular thermocouple vs millivolt
curve is in accordance with the latest ASTM and IPTS
standards for exact temperature simulation. 
Thermocouple types B, E, J, K, R, S and T are
available in both degrees F and C. Resolution is 25,
50 or 100 degrees, corresponding to full scale output
of 500, 1000, 1700, 2100 and 3100 degrees
respectively.
Dual ranges, with an individual “ON” position for each
range, allow quick, easy settings for any output.
Calibrated accuracy is ±0.1% of span ±1 degree.
Negative temperatures add ±2 degrees.
Two built-in AA cells provide power for one year of
everyday use. A front panel LED pulses every time the
Model 22 is turned on to indicate proper battery
voltage.
The low cost Altek Model 22 is a complete, compact
source for checkout and calibration of all
thermocouple instruments in the field, shop or control
room.
General description
Select the Altek Model 22 for the correct thermocouple type, the
desired temperature scale (F or C), and range. Connect the Model
22 to the input terminals of the instrument to be tested, the field
mounted head or junction box terminals.
Cold-junction compensation and instantaneous automatic
standardization is built into the Model 22.
Set the temperature selection switch to the desired temperature
and slide the “ON” switch to the selected scale. The Battery Check
LED will pulse once indicating proper battery voltage. If no pulse is
seen, the batteries should be replaced with 2 “AA” cells. Alkaline
cells are preferred for longest life and widest operating temperature
range.
End point calibration temperatures of the instrument are then
selected on the Model 22 and any required adjustments are made.
Intermediate points may then be selected to verify instrument
linearity or check critical points.
Operating instructions  
						

							PN 1886665 Rev A April 2002
©2002 Altek Industries, Inc. Specifications subject to change without notice. 
All rights reserved. Printed in U.S.A.  
Altek products are warranted to be free from defects
in material and workmanship (excluding fuses,
batteries and leads) for a period of three years from
the date of shipment. Warranty repairs can be
obtained by returning the equipment prepaid to our
factory. Products will be replaced, repaired, or
adjusted at our option. Altek gives no other
warranties, including any implied warranty of fitness
for a particular purpose.Also, Altek shall not be liable
for any special, indirect, incidental or consequential
damages or losses arising from the sale or use of its
products.
Warranty
(Unless otherwise indicated, specifications are in ±% of span@ 23˚C)
Accuracy:  Positive temperatures ±0.1% of span ±1 degree. 
Negative temperatures ±0.1% of span ±3 degrees
Cold junction compensation:  Built-in for specified T/C type
Cold junction temperature effect:  Within ±0.25 degree at 75°F
(20°C) ±0.025 degrees/degree change in ambient
Operating temperature range:  -10 to +130°F (-25 to +55°C)
Ambient temperature effect: Zero:  Included in cold junction effect
Span:  ±0.01% of span/degree
Specifications
Thermocouple types and ranges
TYPE B,R,S DEG C TYPE E,J,K,T DEG F TYPE J,K DEG F TYPE E,J,K DEG F TYPE B,R,S DEG F
TYPE E,J,K,T DEG C TYPE E,J,K DEG C
Storage temperature limits:  -40 to +160°F (-40 to +70°C)
Output impedance:  Fixed, 50 ohms nominal
Batteries:  2 AA alkaline cells provide 1 year of use at nominal 4
hours each workday. Batteries should be removed when storing the
unit longer than 3 months.
Battery indicator:  LED light pulse at turn-on in either range
Size:  2 1/8 x 4 x 2 1/4 inches (54 x 102 x 55 mm)
Weight:  6 oz. (0.15 kg)
Specify thermocouple type, scale range and °F or °C to insure
prompt delivery of all the above standard ranges. A 22J 1000F
completely describes an Altek 22 position source providing a
maximum output of 1000°F for a type J thermocouple
Chromel and Alumel are registered trademarks of 
Hoskins Manufacturing Company.
BPt 30% Rh - Pt 6% Rh
EChromel®- Constantan
JIron - Constantan
KChromel
®- Alumel®
RPt - Pt 13% Rh
SPt - Pt 10% Rh
TCopper - Constantan
500
1000
1700Maximum
2100Scale
3100ReadingF -Degrees Fahrenheit
C -Degrees Celsius
22
Ordering information