Ampro Corporation Ampro Projector 5200 User Manual

19
5200 User’s Manual
Menu System
As previously mentioned, ALICE operates on layers of command button menus. The initial command
buttons (below) allows you to access all of the user type projector controls.
Main Menu
Picture
Allows the user to adjust image quality functions such as, brightness, and contrast, clock
phase and some adv ance settings as well.
Source
Allows the user to explicitly select the display source type. I.E., RGB, RGB2, VIDEO etc.
Setup Wizard
The Setup Wizard allows the user to step...

Menu System
20
5200 User’s Manual
Picture Command  - The user is provided with a new set of command controls. The
numbers of controls are depended on the particular mode, i.e. RGB versus Video. These
controls are used to adjust the image quality of the projected image, with additional advance
controls for black level, gain, filter, odd/even setting and blanking.
 RGB MODE
VIDEO MODE
Bright
Adjust the brightness lev el until the black portions of the projected image are black, buts
details in the shaded...

Menu System
21
5200 User’s Manual
Advanced “continued”
Odd/Even
Certain signals may require you to set the ODD/EVEN parameters. Once selected, you are
presented with an option box for selection. If your image appears jagged or the fields are
offset or seem out of order, switch between STANDARD or NON-STANDARD mode. The
setting of the ODD, ODD PLUS 1 and ODD MINUS 1 is only available when NON-
STANDARD mode is selected. Primarily used for interlaced sources.
  The START parameter is used to set the low...

Menu System
22
5200 User’s Manual
Source Command  - Is used to select the desired input or display mode. With all available
options installed, the user may select between two (2) RGB modes, two (2) Video modes and
the internal graphics mode.
RGB-1
The RGB-1 input includes separate connectors for RED, GREEN, BLUE video signals, plus
separate connectors for Composite Sync  (Horizontal Drive in the case of five (5) wire inputs)
and Vertical Drive.
The Analog RGB input falls into three major categories,...

Menu System
23
5200 User’s Manual
Setup WizardThe SETUP WIZARD will guide the first time user through a step-by-step setup of the various
image parameters or even if you are an experience user, the Setup Wizard provides a quick
method of setting up a new source.
Main Screen
and FunctionsThe Setup wizard screen provides you with the function list. Use the Back/Next buttons to
move through the list. The Setup Wizard screen also provides the adjust meter along with
brief function instructions. The restore...

Menu System
24
5200 User’s Manual
User’s SetupThe User Setup command allows random access the setup controls of the projector.
The more experienced operator typically uses this function.
H Pos
Centers the active video area within maximum display area. Adjust for minimal image
loss from side-to-side. Set the start point of the image on the left side. Adjust until the
left edge of the image is just visible, but not cutoff.
V Pos
Centers the active video area within maximum display area. Adjust for minimal...

Menu System
25
5200 User’s Manual
User’s Setup “continued”
Scaling
Provides the user with the ability to blank all four sides, Size or “zoom” the image in the
horizontal, vertical or both directions, center the image horizontally, vertically or snap
the image to horizontal/vertical centers. See Scaling controls.
Blanking - Adjust the four sides of the
image until all unwanted v ideo is
eliminated or wanted information is
visible.
Zoom – Adjust the image size in the
horizontal, vertical or both directions...

Menu System
26
5200 User’s Manual
User’s Setup “continued”
Advanced “continued”
View Data
The View Data provides a comprehensiv e listing window of all of the user channels.
This listing includes all the statistics that make-up a particular channel.

  The Highlighted column denotes the currently selected channel.

  Use the scroll bars at the bottom and right sides to move up-and-down or left-to-
right.
ModeThere are three (3) modes or processing choices for selection through the pop-up
option box. The...

Menu System
27
5200 User’s Manual
Menu-ChannelsUse the Channels command to access the channel management system with the
following functions.
Select
Highlight the desired channel, then press Select to choose the channel for display.
Save As
First highlight the desired channel, then press Sav e As to evoke the Save As pop-
up window. The Save As command will automatically select the next open channel
number.
Copy
The Copy command provides the ability to copy from channel to another. Once
chosen, the Copy...

Menu System
28
5200 User’s Manual
Menu Command “continued”
Menu-Utility
Sev eral projector set-up and configuration commands are found under the Utility
command.
OrientAllows the user to select the desired projection application for the following modes.
Front-Floor, Front-Ceiling, Rear-Floor and Rear-Ceiling. Press the Orient button to
access the pop-up option box.
Freeze
Toggle Function. Use the Freeze command to freeze the motion of the projected image.
Patterns
Use the Patterns command to display a...