AMT Datasouth Printer Accel 7350 User guide

 
 
 
 
Accel-7350 
 
24-Pin Dot Matrix Printer  
 
 
User’s Guide 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Document Number: 130013   

 CONTENTS 

 CONTENTS 

Chapter 1 
Page 3 of 46 
 
 
 
This device complies with Part 15 of the FCC Rules. 
Operation is subject to  the following two conditions: 
FCC 
Class B 
(1) This device may not cause harmful interference, 
and (2) this device must accept any interference 
received, including interf erence that may cause 
undesired operation. 
 
The manufacturer is not responsible for any radio or 
TV interference caused by unauthorized modifications 
to this equipment. Such modifications could void the 
user’s...

Chapter 1 
Page 4 of 46 
Copyright Declaration 
Information in this manual is subject to change without notice and does not 
represent a commitment on the part of AMT Datasouth Corporat ion. No part of 
this manual may be reproduced or transmitted  in any form by any means, for any 
purpose other than the purchaser’s personal use, without the expresse\
d written 
permission of AMT Datasouth Corporation. 
 
As an ENERGY STAR Partner, the m anufacturer has determined that this 
product meets the ENERGY...

Chapter 1 
Page 5 of 46 
 
Safety Cautions 
 
 
 
 
 
 
 
 
Safety Cautions
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 Do not touch the print head immediately 
after printing because it may be too hot. z Use two hands and hold firmly at 
each end when lifting the cut sheet 
feeder. Personal injury can occur if 
the CSF unit is dropped.  z 
Do not put your finger under the tractor 
cover while loading fanfold paper. z 
z Do not put your finger on the tractor 
gear, when using the rear...

Chapter 1 
Page 6 of 46 
•Unpacking the printer  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
* The packing style is subject to change without notice.  

Chapter 1 
Page 7 of 46 
• Connecting the printer to the power source 
• Make sure that the power switch is set to off. Connect 
the printer with the suppli ed power cord to an AC 
outlet. 
 
 
 
 
 
 
 
 
  Connect the AC power plug to an AC outlet of the 
voltage designated on the rating label on the back of 
the printer. 
• The AC outlet shall be installed near the printer and 
shall be easil
y accessible.
 
 
• Connecting the printer to the computer  
1. Parallel interface 
Make sure the power...

Chapter 1 
• Installing the ribbon cassette 
 
1. Turn off the power. Open the front cover.  
Move the print head to the left end position. 
 
 
 
 
 
 
 
 
 
 
 
 
 
Caution 
Do not touch the print head 
immediately after printing because it 
may be too hot. 
 
 
2. Remove the Red Locking material located at the  
center of the ribbon casse tte, attach the cassette, 
as shown below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Page 8 of 46  

Chapter 1 
3.  Fit the holes in the ribbon attachment to the right and left projections on the 
print head.    
 
 
 
 
 
 
 
 
 
 
Make sure that the ribbon is  properly positioned under 
the edge of the print head.  
 
4. Turn the ribbon feed knob counterclockwise 
to remove any slack in the ribbon. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Page 9 of 46