Anetsberger Brothers 14Inch Gas Fryer MX142E Discontinued User Manual

1
Models
MX-14E, MX-14-2E,
MX-7E,
MX-14AA, MX-14-2AA,
MX-7A
Anetsberger Brothers, Inc.
180 North Anets Drive  •  Northbrook, Illinois  60062  •  847-272-0770  •  Fax 847-272-1943
For ANETS   Factory Warranty Service  •  800-837-2638
Installation,
User Operation,
&
Maintenance
Manual
Keep this Manual in a Convenient Location for Reference
The Anets GoldenLine
Quality Equipment For The Restaurant, Supermarket, and Bakery Industries
MX-14E shown with optional casters
WARNING
After installation of this...

2
CONTENTS
Shipping Container Inspection.......................................................  3
Fryer Gas Supply Specifications....................................................  4
Fryer Electrical Specifications.......................................................  5
Figure 1  - Fryer MX-14E Wiring Diagram............................  5
Code Requirements......................................................................  6
Figure 2 - Fryer Site Installation Requirements..........................

3
DANGER
Read these specifications, Code Requirements, Installation Requirements, Instal-
lation Instructions, and Operating Instructions 
very carefully.  Failure to follow the
Instructions could cause the fryer to malfunction.  A fryer malfunction can result in
property damage, serious bodily injury, or death.
!
1. Carefully examine the shipping container for external damage.  When damage is noted, notify the
delivery carrier immediately.  Save all packing materials for damage claim examination.
2. If...

4
FRYER GAS SUPPLY SPECIFICATIONS
Please make sure that your desired fr yer location has gas
supply factors that are suitable for this product:
Gas Supply Inlet Pipe must be ¾”  NPT (National Pipe Thread) standard gas line.  The gas supply inlet
line should be as straight as possible (fewest bends or elbows) to obtain the highest available gas pressure at
the appliance.  Locate this inlet line horizontally at the center of the desired fryer location, approximately
8¼”  above the floor.
  NOTE:  Using a...

5
Figure 1.  Fr yer Model MX-14E Wiring Diagram
FRYER ELECTRICAL SPECIFICATIONS
Please make sure that your desired fr yer location has electrical
supply factors that are suitable for this product:
120 Volts, 60 Hz, (Refer to Table 1 for amperage requirements), 1-phase, three-wire connection, including
an  electrical ground,  
via a dedicated circuit breaker.   A model-specific electrical circuit diagram is
mounted inside the front door of each fryer.
!
Install a dedicated, three-prong, outlet/...

6
IMPORTANT:  Read the Code Requirements
and the Installation Requirements and Iinstruc-
tions carefully, 
before starting the installation.
Contact the factory (800/ 837-2638) if any
problems or questions arise.
The fryer installation must conform with  local
codes, or in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1 (latest
edition); the Natural Gas Installation Code, CAN/
CGA-B149.1 (latest edition);  or the Propane Gas
Installation Code, CAN/CGA-B149.2 (latest
edition), as...

7
INST INSTINST INST
INST
ALLA ALLAALLA ALLA
ALLA
TION INSTR TION INSTRTION INSTR TION INSTR
TION INSTR
UCTIONS UCTIONSUCTIONS UCTIONS
UCTIONS
Install the fryer in accordance with the preceding
Code Requirements, as well as the following
Installation Requirements.
1. DO NOT install this fryer in a mobile home,
trailer, or recreational vehicle.
2. Install this fryer in a location that has the fryer’s
electrical receptacle 
nearby (5 feet or less
away) to avoid straining the fryer’s power
cord.  (See...

8
Figure 3.  Typical Leg Installation
LEG LEVELING INSTRUCTIONS
1. Move the fryer to its desired location.
WARNING
The fryer MUST NOT tip, rock or wob-
ble, to avoid splashing or spilling its HOT
shortening contents during operation.
!
2. Turn the screw-type leg adjustment ends as
necessary to level the fryer, until NO tipping,
rocking, or wobbling is evident.
3. Perform the Fryer Restraining Device
Installation Instructions, referring to
Figure 2.
INST INSTINST INST
INST
ALLA ALLAALLA ALLA
ALLA
TION...

9
INST INSTINST INST
INST
ALLA ALLAALLA ALLA
ALLA
TION INSTR TION INSTRTION INSTR TION INSTR
TION INSTR
UCTIONS UCTIONSUCTIONS UCTIONS
UCTIONS  (Continued)
CASTER LEVELING INSTRUC-
TIONS
1. Move the fryer to its desired location.
2. Determine whether the fryer tends to wobble
or rock when in its desired location.  If it
does, perform steps 3 through 9.   If it does
not, skip to step 10, then proceed to the
Installation Instructions.
WARNING
The fryer MUST NOT tip, rock or wob-
ble, to avoid splashing or...

10
GAS & ELECTRIC CONNECTION INSTRUCTIONS GAS & ELECTRIC CONNECTION INSTRUCTIONSGAS & ELECTRIC CONNECTION INSTRUCTIONS GAS & ELECTRIC CONNECTION INSTRUCTIONS
GAS & ELECTRIC CONNECTION INSTRUCTIONS
Installing your ANETS  Fryer requires the fol-
lowing procedure, 
after its legs or casters are pro-
perly attached and  it is in its desired location.
1. Ensure that the gas control valve knob in the
fryer has its OFF position next to the valve
mark.
2. Ensure that the gas supply inlet line valve is
closed...