Anschutz LaserPower II Laser Rifle User Manual

							If.t\fe.biat\flon.target.is.not.to.be.used.for.long..
periods,.t\fe.batteries.must.be.removed.to.prevent.
damage.due.to.leakage.or.corrosion.
No Te!
T\fe.life.of.t\fe.batteries.in.t\fe.biat\flon.target. .
depends.on.t\fe.frequency.of.use..Wit\f.frequent.use,.
it.is.entirely.possible.for.t\fe.batteries.to.be.drained.
wit\fin.1-2.days..A.low.batter y.c\farge.condition.
in.t\fe.biat\flon.target.is.indicated.by.a."LO".in.t\fe.
display.
No Te!
Only.batteries.of.t\fe.same.brand.and.t\fe.same. .
type.may.be.used.toget\fer.
T\fe.batteries.must.always.be.replaced.at.t\fe.same.
time.(do.not.fit.old.and.new.batteies.toget\fer).
No Te!
11
Batteries.are.\fazardous.waste.and.do.not.belong. .
in.t\fe.\fouse\fold.refuse..Used.batteries.must.be. .
disposed.of.in.t\fe.used.batter y.container.
No Te! Mains unit
The biathlon target can also be 
powered fro\f the \fains if desired. 
The battery circuit is interrupted 
\bswitched off) when the power unit 
is connected. Therefore it is not 
necessary to re\fove the batteries 
when using \fains po\fwer.
Intended use of the mains unit:
Unilateral \fodification and/\for changing the \fains unit is no\ft per\fitted 
for safety and certification reasons \bCE).
Any other use than that described is not per\fitted and can lead to 
da\faging the product or short circuits, fires or electrocution.
The mains unit sup\yplied is intended exclusively 
\for the Laser\bower biathlon target. Do not use it 
\for other units. 
For operating at mains voltage you must only 
use the genuine ANSCHÜTZ mains unit  
(voltage 6 Volt)!
\blease also observe the country-specific  
stipulations in this matter!
CauTIoN!     
						

							Safety instructions:
To \faintain the technically perfect condition of the unit and to guaran-
tee safe operation, you \fust always observe the safety instructions and 
warnings.
•  Ask an expert if you are not clear about the function, safety or con-
nection of the unit.
• Store away fro\f access by children!
• Keep s\fall parts etc. away fro\f children and pets.
•   In co\f\fercial buildings, co\f\fply with the accident prevention stipu-
lations for electrical equip\fent and devices of the relevant professio-
nal association.
•   The hands, shoes a\fnd clothes and the floor and \fains u\fnit \fust 
re\fain dry during use.
•   Do not connect the \fains unit if you have brought it fro\f a cold 
roo\f into a hot roo\f. The condensati\fon produced can destroy the 
unit. The unit \fust be allowed to war\f up to roo\f te\fperature befo-
re switching it on.
• The \fains unit war\fs up in use. Ensure adequate ventilation.
•   Do not leave the \fains unit and c\fonnected unit unsupervised during 
operation.
12
•  Pull the \fains unit fro\f the plug socket if the unit is not being used 
for an extended period.
• In the event of a \falfunction\f, separate the unit fro\f the plug socket.
•   In order to separate the unit co\fpletely fro\f the \fains, separate the 
\fains unit fro\f the plug socket or the adapter fro\f the unit.
•   Mains units are not intended for use on hu\fans or \fani\fals.
•   Use under adverse conditions \be.g.\f \foisture, too high hu\fidity, dust, 
fla\f\fable gases, vapours or solvents) is not per\fitted.
•   Take the unit out of service if: 
– there are visible indicati\fons of da\fage, 
– it stops functioning per\ffectly, 
– it has been stored under unfavourable conditions or\f 
– it has been exposed to severe loading during transport.
•   Also observe the additional safety instructions in each chapter of this 
operating instruction \fanual.
\faintenance and cleaning \cof the mains unit:
The \fains unit does\f not need any \faintenance. Never dis\fantle the 
unit because otherwise the CE approval and the warranty/guarantee 
beco\fes invalid. In order to prevent da\fage, it should only be re-
paired by an expert or a specialist workshop. 
Clean the \fains unit only with a soft non-fraying cloth. Do not use 
any cleaning agents. Dust can be re\foved with a soft paintbrush or a 
vacuu\f cleaner.
Dis\bosal of the mains unit:
Worn out and defective units \fust be taken to 
public collection p\foints for electrical waste.
The warranty/guarantee will become invalid \for 
damage caused by non-observance o\f this ope-
rating instruction manual! We accept no liability 
\for consequential losses! We accept no liability 
\for material damage or personal injury caused 
by improper handling or no\yn-observance o\f the 
sa\fety instructions. In these cases, the warranty/
guarantee becomes invalid.
No Te!     
						

							7.3	remote	control		
	
	
	
	
	
Two Cr 2016 button cells [20] are required for the remote   
control unit.
Fig.9 Button \bells
 
X Open the battery compartment cover (on the rear side of the 
remote controller) with a suitable tool.
Fig.10 Opening the\s battery \bompartment
 
9 The battery compartment is now open.  
X remove the Cr 2016 button cells [20] from the remote   
control unit [21] (see arrow).
Fig.11 Battery \bompartment open
 
X replace the batteries (the "+" terminals must face upwards).
 
X Close the battery compartment cover again.
Fig.12 Battery \bompartment \bover \blosed
13
[20][21]
You.can .use .a .remote .control .to .operate .more.
t\fan .one .target .unit .at .t\fe .same .time, .since. .
t\fe .remote .control .and .target .unit .are .not.
made .to .matc\f .eac\f .ot\fer .in .eac\f .case.
No Te!
[20]     
						

							14
8	Shooting	
 
X switch the biathlon target on (On/Off switch [14] to "I").
[14]
Fig. 13 Swit\bhing o\sn the biathlon tar\sget
 
X Press the loading button [1] on the l aserPower II rifle,  
aim and pull the trigger [7].
Fig.14 Loading and \sshooting
 
9 Hits are displayed by a green light signal on the biathlon 
target.
[1]
[7]
The hits display is reset using the remote control [21]. 
X Point the remote control [21] at the biathlon target and   
press the button.
 
9 The biathlon target is reset when all the lights go out.
8.1	 engaging	the	safety	on	the	LaserPower	II	rifle	
The trigger safety at the side [3] (where present) can be operated 
when the rifle is cocked. The safety is engaged when the safety 
catch is in the rear position (direction of arrow).
Fig.15 Trigger safety
[2]     
						

							8.2	releasing	the	safety	on	the	LaserPower	II	rifle	
The safety on the l aserPower II rifle is released when the safety 
catch (where present) is in the forward position (direction of   
arrow).
Fig.16 Trigger safety
8.3	 Target	reducer	
The target reducer [17] and the biathlon target [10] are provided 
with Velcro pads.  
X To fasten the target reducer [17] to the biathlon target [10], 
press the reducer [17] on to the target [10] using light pres -
sure (the attachment points on the two components must be 
facing each other).
 
9 The target reducer can be quickly attached and removed as 
required.
15
8.4	 Laser	alignment	
The laser is factory set to a range of 10 metres.
For varying distances, the use of a rear sight from the ansCHÜTZ 
range of accessories is recommended. The alignment is then   
carried out using the rear sight adjustment.
[2]     
						

							8.5	rear	sight	adjustment	
The ansCHÜTZ l aserPower II rear sight can be adjusted both 
vertically and horizontally.
sighting in: The target point always responds to the setting of the 
rear sight [2]. Moving the rear sight [2] to the right causes the 
shot to be displaced to the right. Moving the sight upwards causes 
the shot to be displaced upwards.
Fig.17 Rear sight
 
X To access the adjusting screws, unscrew the aperture [x].
Fig.18 Removing th\se aperture
 
X For vertical adjustment, loosen screw [a] on the left hand   
side of the sight by approximately half a turn.
 
X slide the sight [b] up or down the dovetail and tighten   
the screw [a] again.
Fig.19 Rear sight a\sdjustment
 
X For horizontal adjustment, loosen screw [c] on the right hand 
side of the sight [b] by approximately half a turn.
 
X slide the sight [b] to the right or the left and tighten   
the screw [c] again.
Fig.20 Rear sight a\sdjustment
16
[a] [b]
[c]
[b]
[3]
[x]     
						

							9	Maintenance	 /	cleaning
$
$ The$inside$of$the$\barrel$of$the$LaserPo\fer$II$rifle$must$al\fays$\be$kept$free$of$dirt,$
dust,$sno\f,$etc.
$
$ A$soft,$dry$cloth$must$\be$used$to$clean$the$LaserPo\fer$II$Set.
$
$ For$stu\b\born$dirt,$the$cloth$can$\be$moistened$slightly$and$soaked$\fith$a$mild$$
cleaning$agent.
$
$ Dry$the$LaserPo\fer$II Set$\fith$a$soft$cloth.
P\fysical.damage!
Damage to the product caused by chemicals.
 
h no abrasives, scouring pads, alcohol, paint 
thinners, petrol or cloths that have been   
treated with chemicals may be used to clean 
the l aserPower II set.
CauTIoN!
10	PC	interface	
T\fe.relevant.instructions.of.t\fe.PC.and.t\fe.software.
manufacturers.must.be.obser ved.
No Te!
For competition purposes, the biathlon target can be connected, 
eg. to a PC, using the rs -485 interface cable [18]. (2 targets can 
also be interconnected using the interface cable).
 
X Connect the rs -485 interface cable [18] to the interface [12] 
on the biathlon target and, using eg. an rs -485/UsB adapter 
(not shown), to a PC.
Fig.21 Interfa\be
 
9 The biathlon target is connected to a PC.
17
[12]
[12] [18]     
						

							ANSCHÜTZ.does.not.itself.market.any.software,..
nor.does.it.offer.any.software.support.
No Te!
Up.to.99.biat\flon.targets.can.be.interconnected. .
over.t\fe.RS-485.interface.[12].and.evaluated..
using.appropriate.software.(competition.mode).. .
T\fe.targets.are.automatically.configured.wit\f. .
a.unique.consecutive.target.number,.w\fic\f.is..
indicated.in.t\fe.information.display.[11].
.
It.is.also.possible.to.supply.power.to.several. .
biat\flon.targets.via.t\fe.RS-485.cable.[18].w\fen. .
only.one.power.unit.[19].is.available..In.t\fis.case,.
\fowever,.a.maximum.of.only.6.targets.can.be..
supplied.wit\f.power.from.t\fe.power.unit.[19].
No Te!
11	Technical	data
Weight  .......................................................... approx. 2.2 kg
Overall length of l aserPower II rifle .............................. 95 cm
system length  ............................................................. 66 cm
l aser classification  ...................................... Class 1 (≤ 1mW)
Batteries for l aserPower II rifle  .................................. 2 x aaa
Batteries for remote control  ............. 2 x Cr 2016 lithium cells
Batteries for biathlon target  ........................................ 2 x aa
Biathlon target interface  ............................................ rs-485
Biathlon target operating time (leD on)  ........ approx. 24 hours
Biathlon target operating time (leD off)  ...... approx. 150 hours
l aserPower II rifle operating time  ...................... approx.1 year
r emote control operating time  ......................... approx.1 year
18     
						

							12	Troubleshooting
FaultPossible causeRemedy
Rifle:
No laser spot Batteries too low Replace batteries
Laser actuator defective Send for repair
Laser not exactly on target Laser not aligned correctly Send for alignment
Trigger does not release Trigger not cocked Cock the LaserPower
Trigger safety engaged Release trigger safety
B
iathlon target:
Laser hits but target does not 
light up Target not switched on Switch on target
"LO" (Low battery) appears in 
display Replace batteries
Batteries are flat
When operating with plug-in 
power unit Connect power
Replace plug-in power unit
Target does not respond with 
every shot "LO" (Low battery) appears in 
display Replace batteries
Batteries are flat
Original plug-in power unit 
being used? Use original plug-in power 
unit
R
emote control:
Range too short Batteries low Replace batteries
Does not even function close in Send both remote control and  biathlon target for repair
Fault diagnosis on the LaserPower II Set
I
mportant: When operating with a plug-in power unit, only use the unit supplied with the 
s
et [19], as otherwise damage to the biathlon target can occur!
13	 Disposal
Before disposal, the l aserPower II set must first be broken down 
into its component materials.
19     
						

							20
14	Miscellaneous
additional information is available on the Internet at   
www.anschuetz-sport.com.
ansCHÜTZ provides news on this product and other products  
in the ansCHÜTZ newsletter, which you can sign up to for free 
on the Internet.
www.anschuetz-sport.com
15	Guarantee
< < <   W A R R A N T Y   > > >
1. \faterial: This product has been released for sale after the product itself, its \faterials and individual co\fponents have been subjected to strict inspection, or the rifl e has de\fonstrated its durability and function during test shooting. J.G. ANSCHÜTZ 
G\fbH & Co. KG offers a full guarantee covering \faterial and \fanufacturing faults \bexcluding broken stocks and springs) 
for a period of two years, provided that the fault can be shown to have been present at the ti\fe of handover of the product. 
No warranty clai\fs will be accepted by J.G. ANSCHÜTZ G\fbH & Co. KG for faults that are the result of i\fproper use or 
unauthorised repairs. The ite\f will either be repaired or replaced at our discretion. Clai\fs for co\fpensation - put forward 
for any legal reason whatsoever – are excluded. 
2.  Shooting  Performance:  The  purchaser  undertakes  to  infor\f  J.G.  ANSCHÜTZ  G\fbH  &  Co.  KG  in  writing  of  any 
faults  detected  in  shooting  perfor\fance  within  one  \fonth  of  purchase  with  the  sub\fission  of  their  own  shooting  record. 
J.G. ANSCHÜTZ G\fbH & Co. KG reserves the right to transfer the rifl e to an independent agency for inspection \bDEVA 
or a national ballistics offi ce). Should such an agency confi r\f excellent shooting perfor\fance, J.G. ANSCHÜTZ G\fbH 
& Co. KG is entitled to charge the purchaser the costs of the rifl e inspection. The accepted warranties do not apply to rifl e 
da\fage resulting fro\f \fechanical effects and i\fproper use or care by the purchaser. The warranty is excluded if the rifl e 
has been repaired or \fodifi ed by unauthorised persons. Likewise, the warranty is cancelled when using reloaded a\f\funition or a\f\funition which is not CIP approved. 
In the event of a warranty/da\fage clai\f please encl\fose this card, 
co\fpleted and signed by your dealer, with the product.
J.G. ANSCHÜTZ GmbH & Co. KG · Jagd- und S\bortwaffenfabrik
Postfach 1128 · D-89001 Ul\f/Ger\fany · www.anschuetz-sport.co\f
SERIAL-NO.:
DATE:
THIS ITEM WAS BOUGHT FROM: 
(Stamp and signature of dealer)