Anthem Ltx 300 Lcos Projector Instructions

  
ENGLISH
41
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
 Registering User-defi ned Picture Mode
1
 
     
Select the picture mode
   
2  Adjust picture quality  
       ● See lChanging the initial setting of picture Mode z
for procedures 
                on adjusting the picture quality.  (
P40)
3  To end
 Registering User-defi ned Picture Mode
from the Menu
1  Adjust picture quality
● See lChanging the Initial Setting of Picture Mode z
for procedures 
    on adjusting the...

5Troubleshooting
42
 Troubleshooting
■ You do not need to worry about the following situations if there is no ab\
normality on the screen.
  ● Part of the top surface or front of the unit is hot.
     
● A creaking sound is heard from the unit.
     
● An operating sound is heard from the inside of the unit.
     
● Color smear occurs on some screens.
Power is not supplied
Is the power cord disconnected?
Insert the power cord (plug)  fi rmly.P24
Is the lamp cover properly shut?Remove the power plug when...

  
ENGLISH
43
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
The image cannot output by HDMI terminal
Is the setup of 
“Control with HDMIz 
function 
“Off”?Set up the “Control with HDMI z function to 
lOff
z.P33 - 11
●
 Even if the “Control with HDMI z function is “On”, there are still some devices cannot reveal imag\
e normally.
Color does not appear or looks strange
Is the image correctly adjusted?
Adjust 
lColor
z and 
lTint
z in the setting menu.P29 - 04  05
Video image is...

5Troubleshooting
44
 What to Do When these Messages 
Are Displayed
Message
Cause (Details)
No device is connected to the input terminal.
The input terminal is connected but there is no signal.
     Input the video signals.
A video signal that cannot be used in this unit has been input.
     Input video signals that can be used.
* The names of input terminals such as COMP. will be displayed in yellow.
This message is displayed when the accumulated lamp time has 
exceeded 1900 hours.
To clear the message,...

  
ENGLISH
45
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
 About Warning Indicators
The accumulated lamp time or warning mode of this unit is displayed by t\
he indicators.
For information on indicator display during normal operation, see 
lControls and Features
z.

 (
P14
)
No. Indicator
Blinking
Time Blinking
Frequency Interval 
between  Blinks ContentWARNING LAMP STANDBY
ON
1--Light on (Red)-- -During standby
Indicator 
display 
in normal 
conditions.
2
--Light on...

5Troubleshooting
46
 Replacing the Lamp
The lamp is a consumable item. If the image is dark or the lamp is turne\
d off, replace the lamp unit.
● When the lamp replacement time approaches, a message is displayed on the\
 screen and the condition is indicated by the 
      indicator.  (
P45)
  Remove the lamp cover
   ●  Remove the screws with a  screwdriver.
Usable Lamp Life
●  The usable lamp life for this unit is 
     approximately  2000  hours.  The
    usable lamp life of 2000 hours is 
    merely...

  
ENGLISH
47
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
Install the new lamp unitCAUTION
● Use only genuine replacement parts  
       for  the  lamp  unit. Also,  never  attempt 
      to  reuse  an  old  lamp  unit.  This  may 
      cause  a  malfunction.
●  Do not touch the surface of a new lamp. 
      This may shorten the lamp life  and 
       cause lamp blowout.
Tighten the screws of the new 
lamp unit
●
 Tighten the screws with a  screwdriver.
● Do not place the...

5Troubleshooting
48
Replacing the Lamp (Continued)
BACK
TEST
HIDE
BRIGHT
CONTSHARP
COLOR
TINT
N.R
GAMMA
C.TEMP
INFO
LENS.APASPECT
LENS
INPUT
STANDBY
ON
MENU
CINEMA1 CINEMA2
NATURALSTAGEDYNAMIC
USER1USER2
USER3
LIGHT
After replacing the lamp, reset the lamp time.
   1  Insert the power plug to the power  
     outlet
 2  Must operate with the remote control 
    in the standby mode (the projector is 
    powered, but is not turned on).
     ● Press in the order as shown.
    
● Press each button within...

  
ENGLISH
49
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
 Cleaning and Replacing the Filter
Clean the fi lter regularly or air intake effi  ciency may deteriorate and malfunction may occur.
Remove the inner fi lter                 CAUTION
                 
 
● Pull the power plug from the power  
    outlet.
                  MEMO 
If the fi lter is damaged or too   
dirty to be cleaned
                        
● 
Wash the fi  lter with water and dry it in a shaded area.
● In...

6Others
50
 RS-232C Interface
Control of this unit via a computer is possible by connecting the comput\
er to this unit with a RS-232C 
cross cable (D-Sub 9 pin).
  

 

 
● PC refers to the controller such as a personal computer.
                                                           
D6D7D4D5D2D3D0D1
  Command Format
The command between this unit and the computer consists of  lHeaderz, lUnit IDz, lCommand z, lDataz and lEndz.
● Header (1 byte), Unit ID (2 bytes), Command (2 bytes), Data (n by\...