Anthem Ltx 300 Lcos Projector Instructions

							  
ENGLISH
41
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
 Registering User-defi ned Picture Mode
1
 
     
Select the picture mode
   
2  Adjust picture quality  
       ● See lChanging the initial setting of picture Mode z
for procedures 
                on adjusting the picture quality.  (
P40)
3  To end
 Registering User-defi ned Picture Mode
from the Menu
1  Adjust picture quality
● See lChanging the Initial Setting of Picture Mode z
for procedures 
    on adjusting the picture quality.  (
P40)
2  Display the setting menu
3  Select lPicture Adjustz  
        
lPicture Modez  lNaturalz
      
       
Register the setting
ExitMENU BACKBack
Select Operate
6500K
2
Normal
0
0
0
0
Picture ModeContrastBrightness
Color Tint
Color Temp.
Gamma
Advanced
Lens Aperture
 Picture Adjust
Natural
Reset
CinemaÎ CinemaÍ
Dynamic 
UserÍ
UserÎ
UserÏ
Stage
Natural
● Adjustment settings of image quality 
    will not be registered if other picture 
    mode is selected before registering 
    these settings.
MENUMENU
MENUMENU
  
  
   
    
   
   4
①Select
②Confirm
USER2
USER1 USER3
CAUTION 
						

							5Troubleshooting
42
 Troubleshooting
■ You do not need to worry about the following situations if there is no ab\
normality on the screen.
  ● Part of the top surface or front of the unit is hot.
     
● A creaking sound is heard from the unit.
     
● An operating sound is heard from the inside of the unit.
     
● Color smear occurs on some screens.
Power is not supplied
Is the power cord disconnected?
Insert the power cord (plug)  fi rmly.P24
Is the lamp cover properly shut?Remove the power plug when the unit is in standby mode and 
close the lamp cover properly. After that, insert the plug again.P47
Is the lamp in Cool Down mode?After the Cool Down mode is complete, turn on the power 
again.P25
Projected image is dark
Is the lamp near exhaustion?
Check the lamp time on the information menu. Prepare a 
new lamp unit or replace as soon as possible when the 
lamp is near exhaustion.
P46 to 48
The unit works when power is turned on but stops abruptly after a few mi\
nutes
Are the air inlets and exhaust 
vent blocked
?
Remove the power plug when the unit is in standby mode and 
remove any blocking object. After that, insert the plug again.P14 to 15
Is the fi lter dirty?Clean the  fi lter.P49
Video image does not appear
Is the correct external input 
selected?
Select the correct external input.P24
Is the AV device properly 
connected?Connect the AV device properly.P18 to 21
Is the power of the AV device turned 
on?Turn on the power of the AV device and play the video.P24
Are the correct signals being 
output from the AV device?Set the AV device properly.P18 to 21
Is the setting of the input terminal 
correct?Set 
lCOMP.
z and 
lHDMI
z in the setting menu according to 
the input signal.P33 -
Is the video image temporarily 
hidden?Press the [HIDE] button to display the video image again.P25
Before sending the unit to your authorized dealer for repair, please check the following points.
The following situations are not malfunctions.
■ Perform the following operations when the unit is unable to operate norm\
ally due to external static or   
    noise.    
  
① When the unit is in standby mode, please pull out the power plug, then i\
nsert again.
     ② Press the power button on the unit to turn on the power again.
■ A sound may be heard when the lamp is off but there is no danger.
■ LCOS device is manufactured using high-precision technology but there ma\
y be some 
    missing pixels or pixels that remain permanently lit up.
1112 
						

							  
ENGLISH
43
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
The image cannot output by HDMI terminal
Is the setup of 
“Control with HDMIz 
function 
“Off”?Set up the “Control with HDMI z function to 
lOff
z.P33 - 11
●
 Even if the “Control with HDMI z function is “On”, there are still some devices cannot reveal imag\
e normally.
Color does not appear or looks strange
Is the image correctly adjusted?
Adjust 
lColor
z and 
lTint
z in the setting menu.P29 - 04  05
Video image is fuzzy
Is the focus correctly adjusted?
Adjust the focus.P24
Is the unit placed too near or too far away 
from the screen? Set the unit at a correct distance from the screen.
P22 to 23
Video images are missing
Has setting been performed for 
screen mask?
Set 
lMask
z in the setting menu to 
lOff
z.P27
|35 - 19
Is the display out of position?Alter the 
lPicture Position
z value in the setting menu to 
ensure that images are not missing.P34 - 17
Remote control does not work
Are batteries installed correctly?
Match the polarities ( or ) correctly when inserting 
the batteries.P17
Are batteries exhausted?Replace with new batteries.P17
Is there an obstructive object 
between the remote control and 
remote sensor?
Remove any obstructive objects.P17
Is the remote control held too far 
away from the unit?Hold the remote control closer to the sensor when 
using.P17
Power is cut off suddenly
Has setting been performed for off 
timer?
Set  lOff Timer
z in the setting menu to 
lOff
z.P38 - 34 
						

							5Troubleshooting
44
 What to Do When these Messages 
Are Displayed
Message
Cause (Details)
No device is connected to the input terminal.
The input terminal is connected but there is no signal.
     Input the video signals.
A video signal that cannot be used in this unit has been input.
     Input video signals that can be used.
* The names of input terminals such as COMP. will be displayed in yellow.
This message is displayed when the accumulated lamp time has 
exceeded 1900 hours.
To clear the message, press the [Back] button.
     Get ready a new lamp unit and replace as soon as possible. Reset th\
e  lamp time after replacing the lamp. (
P46 to 48 )
COMP.
No  Input
COMP.
BACKBack
 Lamp  replacement 
						

							  
ENGLISH
45
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
 About Warning Indicators
The accumulated lamp time or warning mode of this unit is displayed by t\
he indicators.
For information on indicator display during normal operation, see 
lControls and Features
z.

 (
P14
)
No. Indicator
Blinking
Time Blinking
Frequency Interval 
between  Blinks ContentWARNING LAMP STANDBY
ON
1--Light on (Red)-- -During standby
Indicator 
display 
in normal 
conditions.
2
--Light on 
(Green)-- -When the power on 
(Hide Off)
3
--Blinking  (Green) 0.5 
second continuous-When the power on 
(Hide On)
4
--Blinking (Red) 0.5 
second continuous-During cool down
5
-Light on
(orange)----
Lamp replacement is near (P46 to 48 )
(When accumulated lamp time has 
exceeded 1900 hours)
6
-Light on
(orange)----
Lamp has reached the end of life 
(
P46 to 48 )
(When accumulated lamp time has 
exceeded 2000 hours)
7 Light on(Red) Blinking
(orange)
-
0.25 
second 1 time 0.75 
second Lamp does not light up and unit is 
unable to project
8 0.25 
second  2 times 0.75 
second Lamp is turned off during projection
9 0.25 
second  3 times 0.75 
second Lamp cover is removed
10
Blinking(Red)
-
-
0.25 
second 1 time 0.75 
second Abnormalities in the power supply
11 0.25 
second  2 times 0.75 
second Cooling fan stops
(cooling fan gets caught)
12 0.25 
second  3 times 0.75 
second
Internal temperature is too high 
(abnormal internal temperature)
13 0.25 
second  4 times 0.75 
second External temperature is too high 
(abnormal external temperature)
14 0.25 
second 1 time 0.75 
second Abnormal electrical circuit 
(abnormal startup of drive circuit)
Blinking
(orange)
15
0.25 
second 2 times 0.75 
second Abnormal electrical circuit 
(abnormal communication of the 
drive circuit)
16 0.25 
second  3 times 0.75 
second Abnormal electrical circuit 
(abnormal drive circuit of image)
17 0.25 
second  4 times 0.75 
second Abnormalities in the automatic lens cover
   Actions to Be Taken for Warning Mode
When the unit enters into warning mode (No. 7 to 17), it will automati\
cally stop projection, and run the cooling 
fan for about 60 seconds.
After the cooling fan has stopped, pull out the power plug from the powe\
r outlet.
Then, follow the procedures below.
No.
Check Action
7●
 Check that an impact shock has not occurred during operation.
● Check that the lamp unit and lamp cover are correctly installed.
● Check that nothing is blocking the auto lens cover. Turn on the power again.
8
9
17
10
●  Check that nothing is blocking the air inlets.
● Check that the external temperature is normal. Leave the unit until it cools down.
After that, turn on the power again.
11
12
13
14
15
16
If the warning indication is displayed again, please wait for the coolin\
g fan stopped, then pull out the power plug from the power outlet. 
Then call your authorized dealer for repair. 
						

							5Troubleshooting
46
 Replacing the Lamp
The lamp is a consumable item. If the image is dark or the lamp is turne\
d off, replace the lamp unit.
● When the lamp replacement time approaches, a message is displayed on the\
 screen and the condition is indicated by the 
      indicator.  (
P45)
  Remove the lamp cover
   ●  Remove the screws with a  screwdriver.
Usable Lamp Life
●  The usable lamp life for this unit is 
     approximately  2000  hours.  The
    usable lamp life of 2000 hours is 
    merely the average usable life of
    lamps and we do not provide any 
     guarantee  for  this  fi gure.
●
 The lamp life may not reach 
     2000  hours  depending  on  the
      operating  conditions.
●  When the lamp has reached the 
      end  of  its  usable  life,  deterioration 
      progresses  rapidly.
●  If the image is dark or the color tone
      is  abnormal,  replace  the  lamp  unit 
     as soon as possible.
●  Setting Lamp Power to Standard 
will help to prolong the lamp life.
Purchasing the Lamp Unit
       Loosen the screws on the lamp unit
  ●
 Loosen the screws with a  screwdriver.
Please consult your authorized dealer.
■ Lamp Unit
       Part  No.:  BHL5010-S
   Pull out the lamp unit
  ●
 Grasp the handle and pull out the lamp unit.
 Procedure for Lamp Replacement
MEMO
 CAUTION
● Pull the power plug from the power 
      outlet.  Failure  to  do  so  may  cause 
      injuries  or  electric  shocks.
● Do not replace the lamp immediately 
      after  the  unit  has  been  used,  and 
      allow  a  cooling  period  of  1  hour 
     or more before replacement. The 
      temperature  of  the  lamp  is  still  high 
      and  this  may  cause  a  burn.
● Do not apply shock to the lamp unit. 
      It  may  cause  lamp  blowout.
● Do not use fl  ammable air duster to 
      clean  the  internal  parts  of  the  unit. 
      This  may  cause  fi re.
1
2
3
Handle 
						

							  
ENGLISH
47
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
Install the new lamp unitCAUTION
● Use only genuine replacement parts  
       for  the  lamp  unit. Also,  never  attempt 
      to  reuse  an  old  lamp  unit.  This  may 
      cause  a  malfunction.
●  Do not touch the surface of a new lamp. 
      This may shorten the lamp life  and 
       cause lamp blowout.
Tighten the screws of the new 
lamp unit
●
 Tighten the screws with a  screwdriver.
● Do not place the removed lamp unit at 
        locations  that  is  reachable  by  children
        or  near  combustible  items 
●
 Dispose used lamp units in the same
      way  as  fl uorescent lamps

Follow your
      local  community  rules  for  disposal.
Attach the lamp cover
●  Insert the top part (with 2 claws) of the lamp cover into 
      the  unit.
●  Fasten the screws with a  screwdriver.
MEMO
4
5
6
Handle
After Replacing the Lamp 
						

							5Troubleshooting
48
Replacing the Lamp (Continued)
BACK
TEST
HIDE
BRIGHT
CONTSHARP
COLOR
TINT
N.R
GAMMA
C.TEMP
INFO
LENS.APASPECT
LENS
INPUT
STANDBY
ON
MENU
CINEMA1 CINEMA2
NATURALSTAGEDYNAMIC
USER1USER2
USER3
LIGHT
After replacing the lamp, reset the lamp time.
   1  Insert the power plug to the power  
     outlet
 2  Must operate with the remote control 
    in the standby mode (the projector is 
    powered, but is not turned on).
     ● Press in the order as shown.
    
● Press each button within 2-second intervals and press the last 
            button for 2 seconds or more.
       ● [STANDBY/ON]  indicator and [LAMP] indicator blink alternately for 
 3 seconds. After that, the unit switches to standby mode.
Resetting Lamp Time
W   ARNING
LAMP
ST  ANDBY/ON
● Reset the lamp time only when you 
      have  replaced  the  lamp.
● Never reset the service time w hen
 
     the lamp is still in use. Otherwise, 
      the  approximate  standard  for  gauging 
      replacement  time  may  be  inaccurate   
      and lamp blowout may occur.
Press for 2 seconds or more
Light on (Red)
HIDEHIDEBACKBACK
CAUTION 
						

							  
ENGLISH
49
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
 Cleaning and Replacing the Filter
Clean the fi lter regularly or air intake effi  ciency may deteriorate and malfunction may occur.
Remove the inner fi lter                 CAUTION
                 
 
● Pull the power plug from the power  
    outlet.
                  MEMO 
If the fi lter is damaged or too   
dirty to be cleaned
                        
● 
Wash the fi  lter with water and dry it in a shaded area.
● In extremely soiled cases, using a neutral detergent is recommended. 
       Put on rubber gloves when using a neutral detergent.
● After washing the fi
 lter with water, make sure that it is completely dry
      before reinstalling. Otherwise electric shock or malfunctions may occur.
●  Do not clean the fi  lter with a vacuum cleaner or air duster. The  fi lter is 
      soft and may be damaged.
● Replace with a new  fi lter. A dirty  fi lter  
      will dirty the internal parts of the unit 
      and  cause  shadows  on  the  video   
      image.
● To purchase a new  fi lter or when it 
      is  dirty  in  the  internal  parts,  consult 
      your  authorized  dealer.
■  Inner Filter Part No.:
     Replacement Filter: 
     the  appearance  is  black
     PB006560999  (Inner  Filter)
Reinstall the inner  fi lter
                   
1
2
3
Lift up while pushing the claw
Clean the fi  lter
Check that the left 
and right claws are 
locked onto the unit 
						

							6Others
50
 RS-232C Interface
Control of this unit via a computer is possible by connecting the comput\
er to this unit with a RS-232C 
cross cable (D-Sub 9 pin).
  

 

 
● PC refers to the controller such as a personal computer.
                                                           
D6D7D4D5D2D3D0D1
  Command Format
The command between this unit and the computer consists of  lHeaderz, lUnit IDz, lCommand z, lDataz and lEndz.
● Header (1 byte), Unit ID (2 bytes), Command (2 bytes), Data (n by\
tes), End (1 byte)
■
 Header
    This binary code indicates the start of communication.
Binary code Type Description
21Operating command PC
→This unit
3F  Reference  command PC
→This unit
40 Response command This unit
→PC
06 ACKThis unit
→PC
(When the command is accepted without error, it returns to 
PC)
■
 Unit ID
      This  code  specifi  es the unit. The binary code is fi  xed at l8901z.
  RS-232C Specifi cations
Pin No. SignalFunction Signal Direction
2 RxDReceive data PC
→This unit
3 TxDTransmit data This unit
→PC
5 GNDSignal ground
-
1,4,6 - 9 N/C
--
ModeNon-synchronous
Character Length8 bit
ParityNone
Start Bit1
Stop Bit1
Data rate19200 bps
Data formatBinary
T
his unit
Start Bit Stop Bit