AOC 2230fm User Manual

                    
2230Fm User Manual 
1. Preface About This Guide  This guide describes the monitors features, setup, and operation. lnformation in this document is subject to change w ithout notice. 
The sections are as follows: 
  
Safety Instructions
: lists safety information.  
 
Setup
: describes the initial setup process.  
 
Using the Monitor
: gives an overview of how to use the monitor.  
 
Driver
 
 
Technical Support 
: provides tips and solutions for common problems.   
 
Product...

2. Safety Introduction FCC Notice 
 
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) 
NOTE:  This equipment has been tested and found to comply  with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are d esigned to 
provide reasonable protection against harmful inter ference in a residential installation. This equipment generates, uses and can radiate radio frequency  energy, and if not 
installed and used in accordance...

Precautions
 
 WARNING: Use of controls, adjustments, or procedure
s other than those specified in this documentation may resu lt in exposure to shock, electrical hazards , 
and/or mechanical hazards.  
Read and follow these precautions when connecting a nd using your computer monitor:  
PRECAUTIONS   
Do not use the monitor near water, e.g. near a bath tub, washbowl, kitchen sink, laundry tub, swimming  pool or in a wet basement.  
 
Do not place the monitor on an unstable cart, stand , or table. If...

3. Setup Setup the stand and base
 
Please setup or remove the base following below ste ps.  
 
Adjusting Viewing Angle
 
 
For optimal viewing it is recommended to look at th e full face of the monitor, then adjust the monitors angle to your own preference.  
 
Hold the stand so you do not topple the monitor whe n you change the monitors angle.  
 
You are able to adjust the monitors angle from -5° to 20 °.  
 
   

NOTE: 
Do not touch the LCD screen when you change the ang le. It may cause damage or break the LCD screen.  
    
Attaching the Cables
 
Cable Connections On Back of Monitor and Computer  
 
1. Power   
2.HDMI  
3. DVI 
4. Analog  
5. Audio  
6. Earphone 
7. USB  
Turn off your computer before performing the proced ure below. 
1.  Connect the power cable to the AC port on the ba ck of the monitor.  
2.  Connect one end of the 15-pin D-Sub cable to the  back of the monitor and connect the other end to...

 Attaching Wall Mounting Arm
 
Preparing to Install An Optional W all Mounting Arm   
 
This monitor can be attached to a wall mounting arm  you purchase separately. Disconnect power before t his procedure. Follow these steps: 
1.  Remove the base.   
2.  Follow the manufacturers instructions to assemb le the wall mounting arm.  
3.  Place the wall mounting arm onto the back of the  monitor. Line up the holes of the arm with the holes in the back of the monitor.  
4.  Insert the 4 screws into the holes...

 4. Using the Monitor Setting the Optimal Resolution 
 
The recommended resolution for this monitor is 1680  by 1050. To setup the monitor to this resolution, follow the steps below. 
1.  Click  START.  
2.  Click  SETTINGS .  
3.  Click  CONTROL PANEL .  
4.  Double click  DISPLAY.  
5.  Click  SETTINGS .  
6.  Set the resolution  SLIDE-BAR to 1680 by 1050.  
External Controls
 
Press the power button to turn the monitor on or of f. The other control knobs are located at front panel of the monitor (See...

OSD Settings
 
 
Press the Menu (Power) button to activate the OSD w indow. Press left, right, up, down button to navigate through the functions. Once the desired function  is 
highlighted, press the Menu (Power) button to activ ate sub-menu . 
 
In sub-menu, Press up, down button to navigate thro ugh the functions. Once the desired function is highlighted, press 
, 
button to button to change the setting. 
Press Menu (Power) button to return to superior men u.  
 
If you want to adjust any other...

DCB Adjustment 
 
What is DCB?  
  
Dynamic Color Boost (DCB) is an advanced color adju stment technology. Through analyzing RGB signals, DCB creates more vivid and natural images to suit various color 
environment needs. DCB has two types of color enhan cers: “Color Boost” and “Picture Boost” .  
 
       DCC: Dynamic color control  
       ICM: Intelligent color management    
1) How to use Color Boost?   
   
Five color-enhancement settings:   To accommodate various display needs, Color Boost  also...

    
Full Enhance:   W hen Full Enhance is turned on, the color satur ation of the entire screen is fu lly enriched, thus all colors become more vibrant.  
 
   
     
Nature Skin:    W hen Natural Skin is turned on, the red and yel low colors are enriched automatically, thus present s human skin with more natural and truer colors. 
Natural Skin setting is ideal for view ing human p ortrait and detailed skin texture.