AOC Le24h138 User Manual

11
Buttons located at the right side of the TV will operate the same as the\
se buttons on the remote control. 
 
M T SC C
PRE CH
Display
EPGWide
Add Fav
COMP
F a vM U/ E x i tE N
Buttondescription
POWER Press to turn on/off the TV.
TV 
Press to choose TV source mode. 
 AV Press to choose CVBS source mode.
COMP Press to choose Component source mode.
HDMI/PC Press repeatedly to choose HDMI or PC source mode.
PR
0-9  Press to enter TV channel number to select channel. 
 
PRE CHPRE CH Press to display the...

12
Set-Up 
Inserting Batteries into the remote control 
Insert two size AAA batteries (supplied) to the diagram inside the bat\
tery compartment of the remote control. 
attaching the Base
ImporTanT: The Base of the AOC TV must be assembled prior to usage.
1.
 Place the TV set facing down on a soft and flat surface (blanket, foam,\
 cloth, etc.) to prevent any 
damage to TV set.   
2.
 Carefully align and insert the Base to the TV.
3.
 Gently push the Base towards the TV, and then fasten the base with M3...

13
English
Connecting TV 
Cable System or VHF/UHF Antenna System 
You can enjoy standard-definition and high-definition digital programmin\
g (if available in your area), along with standard-definition analog 
programming.
This TV is capable of receiving unscrambled digital programming for both\
 cable and external VHF/UHF antenna. 
It is strongly recommended that you connect the antenna/cable input usin\
g a 75-ohm coaxial cable to receive optimum picture quality. A 300-ohm 
twin lead cable can be...

14
English
Composite Signal Connection
AV
AV IN
CVBS
CVBS
CVBS
PC Connection
Use the TV as a monitor for your PC shown below with the HD15 to HD15 co\
nnection. This TV can also be connected to a PC with DVI or HDMI 
output. (Refer to the separate Quick Setup Guide.)
PC
VGA IN
 Connect the PC IN jack to the PC using the HD15- HD15 cable with ferrite\
 core (analog RGB) and audio cable.
 If the PC is connected to the TV and no signal has been input from the P\
C for more than 30 seconds, the TV enters...

15
pC Input Signal reference Chart 
After connecting the PC to the TV, set the output signal from the PC according to the chart below for 22”\
 24” TV.
Standardresolutionhorizontal(kHz)frequency(Hz)
VESA 640 x 480 31.46959.94
VESA 800 x 600 35.156 56.250
VESA 800 x 600 37.87960.317
VESA 1024 x 768 48.36360.004
VESA 1360 x 768 47.7259.799
WXGA+ 1440 x 900 55.93559.887
WSXGA 1680 x 1050 64.67459.884
FHD 1920 x 1080 67.560
Video Input Signal reference Chart 
After connecting the videol input to the TV, set...

16
USIng aoC TV
Turning the TV on and off
You can turn on the TV by using power switch button on the TV set or on \
the remote controller.
Power Button
English
  

17
language Setting
1M U/ E x i tE NPress menU/exIT to call out MENU.
2
Press ▲/▼ to select “Feature”  , and press oK.
3
Press ▲/▼ to select "Menu Language", and press OK.
4
Press ◄/► to adjust.
5
M U / E x i tE NPress menU/exIT to exit.
Move Select Exit
Feature
Menu language
Menu timeout
Super contrastSleep timer
DCR
Closed caption English
20S
Off
Off
Off
Off
Analog caption
Reset all Off
No
B/L Control
100
English
    

18
Viewing mode Selection
4:3 mode
Suitable for viewing conventional 4:3 programs in 
their normal format.
Zoom1 mode
Use these aspect modes to zoom in and to reduce 
the black bars.
16:9 mode
The original content in this mode has to fill the 
entire screen of the display.
Zoom2 mode
Use these aspect modes to zoom in and to reduce 
the black bars.
English
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
  

19
Switching Input Source
On AOC TV, you can choose signal source on the remote control directly, or press Source to choose the signal source on the display menu.
1.
 When choosing signal source on the remote control directly: Press the following keys to switch input source.
 
M T SC C
PRE CH
Display
EPGWide
Add Fav
COMP
F a vM U/ E x i tE N
COMP
2. When using Source key to choose signal source:
 
M T S
C C
PRE CH
Display
EPGWide
Add Fav
COMP
F a vM U/ E x i tE N
1Press Source to call out source menu.
2...

20
oSd manual Setting 
Channel Search 
This setting is only available in TV mode.
1M U/ E x i tE NPress MENU/EXIT to call out MENU.
2
Press ▲/▼ to select “Channel ”  , and press OK.
3
Press ▲/▼ to select "Tuning mode", and press OK. Select the mode of TV signal as Cable or Air.
4 Press ▲/▼ to select 
"System standard", and press  OK. Set as NTSC-M, Auto, PAL-M or PAL-N. Advise please do not change 
this item after auto search action.
5 Press ▲/▼ to select 
"Auto Search", and press...