Home > Apple > Notebook > Apple ibook g4 early 2004 User Manual

Apple ibook g4 early 2004 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Apple ibook g4 early 2004 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							iBook G4 Take Apart - 130
     Frame
    Frame
    Tools
    No tools are required for this procedure.
    Part Location
    Preliminary Steps
    Before you begin, remove the following:
    • Battery 
    • Keyboard and RAM shield
    • AirPort Extreme Card
    • Memory card
    • Bottom case
    • Bottom shield
    • DC-in board 
    						
    							131 - iBook G4 Take Apart
     Frame • Fan
    • Top case
    • Sleep light board
    • Top shield
    • Display module
    • I/O bezel
    • RJ11 modem cable
    • Hard drive
    • Modem
    • Bluetooth
    • Optical drive
    • Display module
    • Heatsink
    • Logic board
    Procedure
    With all preliminary steps completed, the frame is the remaining part. 
    						
    							iBook G4 Take Apart - 132
     FrameReplacement Note:  The front of the frame includes two integral grommets for positioning 
    the hard drive. Make sure the grommets are in place before reassembling the computer.
    Replacement Note:  If the long EMI strip at the port side of the frame is still attached to 
    the frame, make sure you install it on the replacement frame before reassembling the 
    computer. Refer to I/O Bezel in this chapter. 
    						
    							133 - iBook G4 Take Apart
     Display Housing (Back Case)
    Display Housing (Back Case)
    Tools
    • Soft cloth
    • Torx T6 screwdriver or 5/32 hex driver
    • Black stick (or other nonconductive nylon or plastic tool)
    Note: To organize the screws you remove from the LCD panel assembly, use a tray with 
    divided compartments (such as a plastic ice cube tray).
    Replacement Note: If the tape you remove from this assembly is worn and cannot be 
    reused, use new Kapton tape (Apple part number 922-5025).
    Preliminary Steps
    Before you begin, remove the following:
    • Battery 
    • Keyboard and RAM shield
    • AirPort Extreme Card
    • Memory card
    • Bottom case
    • Bottom shield
    • DC-in board
    • Top case
    • Top shield
    • Modem
    • Display module 
    						
    							iBook G4 Take Apart - 134
     Display Housing (Back Case)
    Procedure
    Important: Although the display pictured in this section may appear different from the 
    display you are working on, the steps are the same.
    1. With the display module lying face up on a soft cloth, use either a 5/32 hex driver or a 
    Torx T6 screwdriver to remove the four screws (two on each side) from the display 
    housing. 
    2. Using a black stick, pry up the bezel from the display housing. Carefully work the black 
    stick around the outer perimeter and corners of the bezel.    
    						
    							135 - iBook G4 Take Apart
     Display Housing (Back Case) 3.Warning: When lifting the assembly, be careful not to strain the cables.
    With the bezel assembly loosened, grasp the display clutch and raise the assembly 
    off of the display housing.   
    4. Place the display assembly face down on a soft cloth.  
    						
    							iBook G4 Take Apart - 136
     LCD Panel
    LCD Panel
    Tools
    • Soft cloth
    • Torx T6 screwdriver or 5/32 hex driver
    • #0 Phillips screwdriver
    • Black stick (or other nonconductive nylon or plastic tool)
    Note: To organize the screws you remove from the LCD panel assembly, use a tray with 
    divided compartments (such as a plastic ice cube tray).
    Replacement Note: If the tape you remove from this assembly is worn and cannot be 
    reused, use new Kapton tape (Apple part number 922-5025).
    Preliminary Steps
    Before you begin, remove the following:
    • Battery 
    • Keyboard and RAM shield
    • AirPort Extreme Card
    • Memory card
    • Bottom case
    • Bottom shield
    • DC-in board
    • Top case
    • Top shield
    • Modem
    • Display module 
    						
    							137 - iBook G4 Take Apart
     LCD Panel
    Procedure
    Important: Although the display pictured in this section may appear different from the 
    display you are working on, the steps are the same.
    1. With the display module lying face up on a soft cloth, use either a 5/32 hex driver or a 
    Torx T6 screwdriver to remove the four screws (two on each side) from the display 
    housing.     
    2. Using a black stick, pry up the bezel from the display housing. Carefully work the black 
    stick around the outer perimeter and corners of the bezel.    
    						
    							iBook G4 Take Apart - 138
     LCD Panel3.Warning: When lifting the assembly, be careful not to strain the cables.
    With the bezel assembly loosened, grasp the display clutch and raise the assembly 
    off of the display housing.   
    4. Place the display assembly face down on a soft cloth.  
    						
    							139 - iBook G4 Take Apart
     LCD Panel 5. Notice the U-shaped notches on the sides of the bezel. 
    6. Remove the four Phillips screws (two on each side) from the display shield. (Carefully 
    move aside any cables or tape that partially block access to the screws.)
    7. Peel up the foil tape that holds the LCD cable to the LCD shield.     
    						
    All Apple manuals Comments (0)

    Related Manuals for Apple ibook g4 early 2004 User Manual