Apple imac 17 inch late 2006 User Manual

							iMac (17-inch Late 2006) Take Apart — Display Panel 51
Removing the LCD Display
Using the black stick, or access tool, carefully peel back the EMI shielding from the left, right, 
1.  
and bottom edges of the computer 
2.  Using a Torx T6 screwdriver, remove the two LVDS cable connector screws. Disconnect the 
LVDS display cable from the logic board.   
922-7010 
						

							iMac (17-inch Late 2006) Take Apart — Display Panel 52
To the right of the battery is the inverter cable connector. Disconnect the inverter cable from 
3. 
the logic board.   
4.  Using the access card or a black stick, peel the EMI tape away from each side of the panel. 
Remove the four panel mounting screws with a T10 screwdriver. 
922-7023 
						

							iMac (17-inch Late 2006) Take Apart — Display Panel 53
Pivot the panel up, as shown, then carefully peel the top edge of the panel away from the 
5. 
EMI shield. Note: Continue with steps 6-12 if you are replacing the display panel. 
  
Note: If replacing a bad LCD display, you will need to remove the lower EMI shield (if still 
attached), the display panel mounting brackets, and the LVDS cable as follows.
Peel the lower EMI shield off the bottom edge of the display panel.
6.  
7.   Using a torx T10 screwdriver, push the tape aside and remove two screws from the left side 
panel mounting bracket. Repeat for the other side. 
922-7158 
						

							iMac (17-inch Late 2006) Take Apart — Display Panel 54
Peel back the clear tape and disconnect the two inverter-to-display cable connectors. 
8.  
To access the LVDS cable connector, peel back the clear tape and the black mylar (if 
9. 
necessary). Pinch together the connector locking levers, and disconnect the LVDS cable 
connector. 
Return the panel to Apple. 
10.   
						

							    
iMac (17-inch Late 2006) Take Apart — Display Panel 55
Replacing the LCD Display
Replace the LVDS cable on the rear of the display panel. 
1.  
Secure the LVDS cable with clear tape and the black mylar. 
2.  
Replace the right panel mounting bracket on the display panel with two T8 screws.
3. 
Replace the left bracket on the display panel with two T8 screws. 
4.  
Connect the two inverter-to-display cable connectors and tape them to the back of the 
5. 
display panel.  
  
						

							    
iMac (17-inch Late 2006) Take Apart — Display Panel 56
Turn over the panel. If the lower EMI shield was removed, reattach the lower EMI shield 
6.  
across the bottom of the panel.
Attach the three pieces of aluminum tape along the bottom of the panel. The tape comes 
7.  
with the replacement panel. The tape should attach to the panel on one side and to the 
lower EMI shield on the other side. 
Position the panel into the rear housing. Make sure the inverter cable and the LVDS cable are 
8.  
accessible and not tucked under the panel.
Secure the panel with four T10 mounting screws.
9. 
Connect the inverter cable connector to the logic board.
10.  
Connect the LVDS cable connector to the logic board and secure it with two T6 screws.
11 .  
Fold the EMI tape firmly over the left, top, and right edges of the display panel. Use the black 
12.  
stick to adhere the tape firmly and rub out wrinkles.
Replace the front bezel.
13 .  
Replace the access door.
14.   
						

							iMac (17-inch Late 2006) Take Apart — LVDS Cable 57
LVDS Display Cable
Tools
No tools are required.
Preliminary Steps
Before you begin, removeAccess doo
•  r
Front beze
•  l
Lower EMI shiel
•  d
LCD Displa
•  y
Part Location 
						

							iMac (17-inch Late 2006) Take Apart — LVDS Cable 58
Remove the LVDS Cable
Locate the LVDS cable on the back side of the display panel. Remove the piece of tape that 
1.  
secures the cable to the panel.  
Pinch together the connector locking levers, and disconnect the LVDS cable connector. 
2.   
						

							iMac (17-inch Late 2006) Take Apart — LVDS Cable 59
Replacing the LVDS Cable
Attach the LVDS cable on the back of the display panel as shown. 
1.  
If you are replacing the display, a piece of black mylar is enclosed in the box with the display 
2.  
module. The dotted lines below show the correct placement of the clear tape and black 
mylar.  
(
Replace the lower EMI shield.
3. 
Lower the display into place. Replace the four display screws.
4.   
						

							iMac (17-inch Late 2006) Take Apart — LVDS Cable 60
Replace the front bezel.
5. 
Replace the access door.
6.