Asus A3000n Service Guide

							DISASSEMBLY PROCEDURE 
 3 - 11 
 
ODD Module 
The illustration below shows how to remove the ODD module. 
 
1.  Remove 2 screws from the cover (No.1, No.2) [M2 * 4L (K) B-NI, NY]. 
 
 
 
2.  Put the screwdriver (No. 3) here and push the ODD drive out from the NB. 
 
ODD MODULE 
 
1 
2 
3 
ODD 
REMOVAL  
						

							DISASSEMBLY PROCEDURE 
 3 - 12 
 
3.  Remove 4 screws  (no.4-7) [M2 * 2L (P) W-NI] from ODD bracket. 
 
 
4 
5 
7 
6  
						

							DISASSEMBLY PROCEDURE 
 3 - 13 
Keyboard  
The illustration below shows how to remove the keyboard 
 
 
Removing Keyboard  
1.  Remove 2 screws here (No.1, No.2) [M2 * 6L (K, D4.6) (K) B-NI, NY]  
 
 
 
2.  Turn over the NB and open the display panel. 
 
3.  Push the 3 latches in (No.1, No.2, No.3) with a pair of tweezers or a single-
slotted screwdriver and lift the keyboard plate up. 
 
 
KEYBOARD 
REMOVAL 
KEYBOARD 
DISASSEMBLY 
1 
2 
1  2 
3  
						

							DISASSEMBLY PROCEDURE 
 3 - 14 
 
4.  Lay the keyboard down over the Touch Pad module.
  *Do not remove the 
keyboard yet.  
The keyboard cable is still attached. 
 
 
 
Removing Keyboard Cable 
 
1.  Use a flexible connector tool to unlock the cable connector on both ends (no. 1). 
2.  Carefully pull out the keyboard cable (no. 2) with a pair of tweezers. 
3.  Lock the connector (no. 3) again to avoid possible breakage. 
 
 
4.  Remove keyboard from the top case. 
 CABLE 
REMOVAL 
1. Unlock 
2. Cable out 
3. Lock 
1. Unlock 
3. Lock 
						

							DISASSEMBLY PROCEDURE 
 3 - 15 
 
5.  Disconnect the connector of touch pad beneath keyboard. 
 
  
						

							DISASSEMBLY PROCEDURE 
 3 - 16 
LCD Module 
The illustrations below show how to remove and disassemble the LCD module.  The 
module contains LCD panel, invert, LCD hinge bracket, hinge cover, LCD front cover 
and LCD bottom case. 
Please do not disassemble the individual parts. 
 
Removing LCD Module 
 
1.  Close the display panel. 
 
2.  Remove 2 screws on the harness cover (No.1, No.2). [M2 * 4L(K) B-NI, NY] 
 
 
 
3.  Remove the harness cover. 
 
4.  Remove 2 screws here (No.3). [M2 * 4L (K) B-NI, NY], (No.4). [M2 * 6L (K, 
D4.6) (K) B-NI, NY] 
 
 
LCD 
 
LCD 
REMOVAL 
1 2 
3 4  
						

							DISASSEMBLY PROCEDURE 
 3 - 17 
 
5.  Disconnect the 2 connectors. 
 
6.  Open LCD, and remove 2 screws on both ends (No.1, No.2). [M2. * 4L] 
 
 
 
7.  Remove 4 screws on both ends (No.3-6). [M2 * 6L] 
 
 
 
8.  Remove the LCD module from system. 
 
 
1 
2 
3 
4  5 
6  
						

							DISASSEMBLY PROCEDURE 
 3 - 18 
 
Disassembling LCD Module 
1.  Remove 5 rubes and 5 screws (No.1 ~ No.5) [M2.5*6L(K) (4.6) B-NI, NY] on the 
LCD bezel. 
 
 
 
2.  Carefully pry the inside edges of the LCD case open on all four edges with your 
fingers. Then, lift it away from the LCD module. 
 
 
 
 
 
LCD DIS-
ASSEMBLY 
3 
1 
4 
5 
2  
						

							DISASSEMBLY PROCEDURE 
 3 - 19 
 
3.  Disconnect the 2 cables on inverter board. (No.7, No.8). 
 
 
 
4.  Remove 4 screws here (no.9-12) [M2.5*6L(K) (4.6) B-NI, NY]. 
 
 
 
 
7 8 
11 
12 
9 
10
  
						

							DISASSEMBLY PROCEDURE 
 3 - 20 
 
5.  Remove 4 screws (no.13-16) [M2*3L(K) B-NI, NYLOK] to separate the LCD 
panel from the LCD back cover. 
 
 
 
 
 
6.  Remove the panel and the 2 hinge modules from the LCD back cover. 
 
 
16 15 
14 13