ATT DEFINITY Communications System Generic 3 For Single-Carrier Cabinets Instructions Manual

							475 or 476 Printer Used as Journal Printer for Hosp itality 
Feature
September 1995 Issue 1 
H-25
Switch 22
1 OFF Baud Rate*
2ON
3ON
4 OFF Not Used
Switch 23
1 ON RS232
2 OFF
3 OFF Use of DSR
4 OFF
5ON
6 OFF Not Used
Switch 24
1 ON Select DTR Timing
2ON
3 OFF Select RTS Timing
4ON
5 ON Use of CTS
6 OFF
7 OFF
8ON
* The Baud Rate Default is 1200 baud. Any speed
can be used, b ut the speed of the printer and
any connection devic e used must match.
Table H-18. Option Switch Settings for 475 Printer 
Connected as System Printer — 
Section Setting Description
Continued on next page 
						

							O ption Switch Setting s
H-26Septemb er 1995 Issue 1  
Table H-19. Option Switch Settings for a 475 or 
476 Journal Printer
Section Setting Description
Switch 1
1 OFF Character Set
2ON
3 OFF
4 OFF
5 OFF DC1 and DC3
6 ON Line Feed
7 ON Print Command Mode
8 OFF LF o n  CR
Switch 2
1 OFF Numeric Display of Zero
2 OFF Buffer Selection
3 OFF TOF-to-TOF
4 OFF Power on Line Feed Pitc h
5 OFF Power on Character Pitc h
6 ON Selection on 7 or 8 Bit Data
7 ON Power on Off-Line or Ready
8 OFF Uni- or Bi-Directional Printing
Switch 21
1 OFF Number of Stop Bits
2 OFF Select SD
3 OFF Parity
4ON
5 OFF Not Ready
6 OFF 7-Bit or 8-Bit Data
7 OFF X/O N X / OFF
8ON
Continued on next page 
						

							475 or 476 Printer Used as Journal Printer for Hosp itality 
Feature
September 1995 Issue 1 
H-27
Switch 22
1 OFF B a u d  Rat e
2 OFF
3 OFF
4 OFF Not Used
Switch 23
1 ON RS232
2 OFF
3 OFF Use of DSR
4 OFF
5ON
6 OFF Not Used
Switch 24
1 OFF Select DTR Timing
2ON
3 ON Select RTS Timing
4 OFF
5 OFF U se  of  C TS
6ON
7 OFF
8ON Table H-19. Option Switch Settings for a 475 or 
476 Journal Printer — Continued  
Section Setting Description
Continued on next page 
						

							O ption Switch Setting s
H-28Septemb er 1995 Issue 1  
470 or 471 Printer Used as Journal
Printer for Hospitality Feature
A p rinter can be connected to the switch to provide hard  copy of hospitality 
related data. Table H-21 shows the o ption switch settings for the 470 or 471 
printers when they are used in this application. Table H-20. Option Switch Settings on Modular Processor 
Data Module (MPDM) or Modular Trunk Data 
Module (MTDM) for 475 or 476 Journal Printer
Switch Setting
SELF TEST OFF
LOC LOOP/REM 
LOOPOFF
1200 BAUD ON
AANS (mo dular 
processor data 
module only)ON
SIGLS ON
PR TY O N
I/OD ON
DIS C ON
KY B D O N
All Others OFF 
						

							470 or 471 Printer Used as Journal Printer for Hosp itality 
Feature
September 1995 Issue 1 
H-29
Table H-21. Option Switch Settings for a 470 or 
471 Journal Printer
Section Setting Description
Switch 1
1 OFF Character Set
2ON
3 OFF
4 OFF
5 OFF DC1 and DC3
6 ON Line Feed
7 ON Print Command Mode
8 OFF LF o n  CR
Switch 2
1 OFF Numeric Display of Zero
2 OFF Buffer Selection
3 OFF TOF-to-TOF
4 OFF Power on Line Feed Pitc h
5 OFF Power on Character Pitc h
6 ON Selection on 7 or 8 Bit Data
7 ON Power on Off-Line or Ready
8 OFF Uni- or Bi-Directional Printing
Switch 3
1 ON In put-Busy to Pin 36
2 OFF Not Used
3 ON Logic Ground on Pin 14
4 OFF Not Used
Continued on next page 
						

							O ption Switch Setting s
H-30Septemb er 1995 Issue 1  
572 Printer
A 572 printer c an function as a G3 Management Terminal, station message d etail 
recording (SMDR), system printer, or journal printer. The options on the 572 
printer are set with function keys rather than d ual in-line package switches. 
Figure H-1 shows the arrangement of the function keys on the printer control 
panel.
Figure Notes:
Figure H-1. Control Panel for 572 Printer
NOTE:
Before attempting to set the printer options, ensure that the printer is 
loaded with paper.
To set the options:
1. Depress Power On and Print Quality buttons simultaneously. This puts 
the printer in the set-up mode and it prints the following settings:
nForm length
nLines per inch
nCharacters per inch
nLetter quality or near letter quality
nBuzzer on/off
Power
OnAlarm Print
QualityOn
LineLine
FeedForm
Feed
345162
1. Power On
2. Alarm
3. Print Quality4. On Line
5. Line Feed
6. Form Feed 
						

							572 Printer
September 1995 Issue 1 
H-31
2. If the printer is to be used with the G3 Management Terminal, station 
message detail recording (SMDR), or as a Journal printer, set the o ptions 
as shown in Table H-22. If the printer is being used as the system printer, 
set the options as shown in Table H-23.
nUse Line Feed button to step forward through the list of functions or 
use Form Feed button to step backward 
						

							O ption Switch Setting s
H-32Septemb er 1995 Issue 1  
.
Table H-22. 572 Printer Used with G3 Management Terminal,
Station Message Detail Recording (SMDR) or 
Journal Printer
572 Printer Option Settings
Function Function Menu Menu
Number Name Number Status
01 FORM  LENGTH 09 11
02 LPI 01 6
03 CPI 01 10
04 LQ or NLQ 01 LQ
05 BUZZER 01 ON
06 FONT 02 FONTCART
07 RESOLUTION 01 144
1 1 BUFFER 0 2 N-LINE
13 PW ON MODE 01 ON-LINE
14 DIRECTION 01 B1-DIR.1
15 BUFF FULL 02 LF + CR
16 P.E. 01 ACTIVE
17 AUTO CARRIAGE 
RETURN (CR)01 CR +  LF
18 ZERO 01 0
22 AUTO LINE FEED 01 CR ONLY
31 1’’ SKIP 01 OFF
32 CHAR.SET (GO, GL) 02 USA
33 CHAR.SET (G1, GR) 01 UK
34 CHAR SET (G2) 03 GE
35 CHAR SET (G3) 07 LINE DRAWING
8 1 O FF- LINE STATE 0 1ALL RECEIVE
82 DSR 02 OFF
83 REQUEST TO  SEND 
TIMING0 1 RTS
84 CD 02 OFF
85 CLEAR TO SEND (CTS) 02 OFF
91 OVER RUN 02 256
92 DATA BIT 02 8 
						

							572 Printer
September 1995 Issue 1 
H-33
93 PROTOCOL 03 XON/XOFF
9 4 STOP BIT 0 1 1
9 5 PARI TY 0 1 NO NE
96 PBS 01 9600
Table H-22. 572 Printer Used with G3 Management Terminal,
Station Message Detail Recording (SMDR) or 
Journal Printer
572 Printer Option Settings
Function Function Menu Menu
Number Name Number Status 
						

							O ption Switch Setting s
H-34Septemb er 1995 Issue 1  
Table H-23. 572 Printer used as System Printer
572 Printer Option Settings
Function Function Menu Menu
Number Name Number Status
01 FORM  LENGTH 09 11
02 LPI 01 6
03 CPI 01 10
04 LQ or NLQ 01 LQ
05 BUZZER 01 ON
06 FONT 02 FONTCART
07 RESOLUTION 01 144
1 1 BUFFER 0 2 N- LI NE
13 PW ON MODE 01 ON-LINE
14 DIRECTION 01B1-DIR.1
15 BUFF FULL 02 LF + CR
16 P. E. 01 ACTIVE
17 AUTO CARRIAGE 
RETURN (CR)01 CR +  LF
18 ZERO 01 0
22 AUTO LINE FEED 01 CR ONLY
31 1’’ SKIP 01 OFF
32 CHAR.SET (GO, GL) 02 USA
33 CHAR.SET (G1, GR) 01 UK
34 CHAR SET (G2) 03 GE
35 CHAR SET (G3) 07 LINE DRAWING
8 1 O FF- LINE STATE 0 1ALL RECEIVE
82 DSR 02 OFF
83 REQUEST TO  SEND 
( RTS) TIMING0 1 RTS
84 CD 02 OFF
85 CLEAR TO SEND (CTS) 02 OFF
91 OVER RUN 02 256
92 DATA BIT 02 8
93 PROTOCOL 03 XON/XOFF