Barco MD-4221 Medical LCD Monitor User Manual

  
 
  21 
Controls 
Remote control 
Key Description 
F1 Input Selection, same as input button on user con-
trols 
F2 PiP Button on OSD 
F3 PiP Swap 
F4 No Function 
F5 Shows RS232 address 
UP Move in OSD same as up key on user controls 
DOWN Move in OSD same as down key on user controls 
LEFT Adjust in OSD, same as - key 
RIGHT Adjust and enter adjust in OSD, same as + key 
ADJ Enter OSD, same as menu button on user controls 
EXIT Exits OSD, same as menu button on user controls 
ENTER Enter OSD submenu,...

  
 
22  
OSD buttons position 
 
OSD Button Function 
An 8-button keypad, located on the right hand side of the display, allows the user to 
make adjustments to various display parameters using the On Screen Display (OSD) 
system.  

  
 
  23 
●Power LED 
Green : Normal mode 
Amber: Standby mode 
Amber: Soft power-off 
●On-Screen Display (OSD) Function Button 
1. POWER :    Turns ON/OFF the monitor. 
2. MENU :    With OSD deactivated, Activate the OSD menu.   
With OSD activated, Exit from main menu   
or sub menu. 
3. PIP :    With OSD deactivated, Hot key of PIP mode. 
4. UP :    With OSD deactivated, Hot key of the brightness control and increases 
the brightness.   
With OSD activated, move the cursor upward. 
5. DOWN :  With...

  
 
24  
On-Screen Display Menus 
Adjust 
   
                       
   
                            
 
 
 
 
 
 
 
  

  
 
  25 
BRIGHTNESS Increase or decrease the brightness. (Range : 0~100) 
CONTRAST  Increase or decrease the Contrast. (Range : 0~100) 
SHARPNESS (1)  Adjusts the sharpness of video image. (Range : 0~100) 
SHARPNESS (2) 
Adjusts the sharpness of video image. (SOFTEST, SOFT, NORMAL, 
SHARP, SHARPEST) 
COLOR (3)  Changes the color value. (Range : 0~100) 
HUE (3)  Changes the Hue. (Range : 0~100) 
BACKLIGHT  Adjusts backlight dimming level. (Range : 0~100) 
PHASE (4)  Adjust backlight dimming level....

  
 
26  
Advanced 
   
           
SCALING  Change the image size 
(Best Fit, Fit Width, Fit Height,Native,Full Display) 
H POSITION (6)  Adjust the horizontal position of the displayed source 
image.(Range : 0~100) 
V POSITION (6)  Adjust the vertical position of the displayed source image. 
(Range : 0~100) 
POWER SAVE  On/Off the power save function 
DISPLAY FUNCTION  Adjust GAMMA value. 
(NATIVE,GAMMA1.8,GAMMA2.0,GAMMA2.2,GAMMA2.4, 
GAMMA2.6,DICOM,VIDEO) 
OVER SCAN  Adjust the displayed size. (0~8)...

  
 
  27 
Setup 
 
LANGUAGE  Change the OSD language. (8 languages) 
BACKGROUND Set the Background color 
RS-232 BAUDRATE  Change RS232 BAUDRATE (115200,38400,19200,9600) 
RS-232 ADDRESS  Set the RS232 Address.(Range : 1~255) 
OSD COLOR  Adjust the OSD background from white opaque to half 
translucent. 
OSD POSITION  Change the OSD position 
OSD TIMEOUT  Adjust time until the OSD Menu will disappear after adjusting 
the menu. (5, 10, 20, 30, 60, 90, 120, 180, 240 seconds) 
RESTORE SETTINGS  Changes the...

  
 
28  
PIP 
 
LAYOUT  Change the OSD layout. (Single, PIP, PBP1, PBP2) 
SOURCE 1  Change the primary source. 
SOURCE 2  Change the secondary source. 
SIZE  Adjust PIP size. (Small,Large) 
POSITION Change the PIP position. (9 positions) 
TOGGLE  Swaps the position of the Primary and Secondary images.  

  
 
  29 
OSD functions description 
Menus Function Descriptions 
BRIGHTNESS  Setting the brightness too high or too low will decrease 
the amount of visible information. 
CONTRAST  Setting the Contrast too high or too low will cause loss 
of some grayscales. 
FREQUENCY  Do not adjust freely. It will adjust fine state 
automatically after auto adjustment. 
When frequency value is wrong, the image has the 
wrong horizontal size or contains noise. 
PHASE  Do not adjust freely. It will adjust fine state...

  
 
30