Beko Dis 1520 N Manual

							28
Rust, discoloration or surface deterioration occurs on dishes
• Salt leakage exists. >>> Salt may cause deterioration and oxidation on 
metal surfaces. Pay attention not to spill salt around the salt filling \
hole 
while adding salt. Make sure that the salt reservoir lid is tightly clos\
ed after 
finishing the filling process. Run the prewash programme to remove the s\
alt 
that spilled inside the machine. Since the salt granules that will remai\
n under 
the lid will dissolve during prewash, causing the lid loosen, check the \
lid 
once again at the end of the programme.
• Salty food remnants have remained on dishes for a long time.  >>> If 
silverware soiled with such foods will be kept waiting in machine, dirt \
must 
be removed by prewash or dishes must be washed without being kept 
waiting.
• Electric installation is not grounded. >>>Check if your machine is connected 
to the actual grounding line. Otherwise, the static electric created in \
the 
product causes arcs on the surfaces of metal items creating pores, remov\
ing 
the protective cover on the surface and causing discoloration.
• Intensive cleansers such as bleaches are used. >>> Protective cover on 
metal surfaces gets damaged and looses its efficiency in time when it ge\
ts in 
contact with cleansers such as bleach. Do not wash your dishes with blea\
ch.
• Metal items particularly such as knives are used for purposes other then\
 
their intended uses.  >>> Protective cover on the edges of knives may get 
damaged when they are used for purposes such as opening cans. Do not 
use metal kitchen utensils out of their intended uses.
• Silverware are made of low quality stainless steel. >>> Corrosion on such 
items is inevitable; they should not be washed in dishwashers.
• Kitchen utensils that are already corroded are washed in dishwasher. 
>>> Rust on a corroded item can migrate to other stainless steel surfaces 
and cause corrosion on those surfaces as well. Such items should not be \
washed in dishwashers. 
EN  
						

							29
Detergent remains in detergent dispenser.
• Detergent dispenser was damp when adding detergent. >>> Make sure that 
the detergent dispenser is dried well prior to filling it with detergent\
.
• Detergent is added long before the washing process. >>> Pay attention to 
add detergent shortly before start-up of the washing.
• Opening of the detergent dispenser lid is prevented during washing. >>> \
Place the dishes in a way that will not prevent the detergent dispenser \
lid 
from opening and the water going into the machine from impellers.
• Detergent is stored under unsuitable conditions. >>> If you are using powder 
detergent, do not store the detergent package in humid places. Keep it i\
n a 
closed container if possible. For ease-of-storing, we recommend you to u\
se 
tablet detergents.
• Impeller holes are clogged. >>> Lower and upper impeller holes might 
be clogged with food remnants such as lemon pips. Clean the impellers 
regularly as illustrated in section "Cleaning and Care".
Decorations and ornaments on kitchen utensils are being erased.
C Decorated glasses and decorated luster porcelains are not suitable for 
washing in the dishwasher. Manufacturers of glassware and porcelain 
tableware items do not recommend washing such kitchen utensils in the 
dishwashers either.
Dishes are scratched.
C Kitchen utensils that contains or are made of aluminum should not be 
washed in dishwasher.
•  Salt leakage exists. >>> Pay attention not to spill salt around the salt filling 
hole while adding salt. Spilled salt can cause scratches. Make sure that\
 
the salt reservoir lid is tightly closed after finishing the filling pro\
cess. Run 
the prewash programme to remove the salt that spilled inside the machine\
. 
Since the salt granules that will remain under the lid will dissolve dur\
ing 
prewash, causing the lid loosen, check the lid once again at the end of \
the 
programme.
• Water hardness setting is low or salt level is insufficient >>> Measure the 
hardness of the supply water appropriately and check the water hardness \
setting.
• Dishes are not placed orderly in the machine. >>> When placing the glasses 
and other glassware into the basket lean them not against other dishes b\
ut 
the edges or racks of the basket or the glass support wire. Striking of the 
glasses to each other or to other dishes due to the impact of water duri\
ng 
washing can cause breaks, or scratches on their surfaces. 
EN  
						

							30
A smear remains on glasses that resembles milk stain which can not be 
removed when wiped by hand. A bluish / rainbow appearance occurs when 
the glass is pointed to light.
• Excessive rinse aid is used. >>>Lower rinse aid setting. Clean the spilled 
rinse aid when adding rinse aid.
• Corrosion has occurred on glass due to soft water. >>> Measure the 
hardness of the supply water appropriately and check the water hardness \
setting. If your supply water is soft (>> Hand-wash detergents do not contain 
antifoam. There is no need to hand-wash the dishes before placing them i\
nto 
the machine. Removing the coarse soil on the dishes under tap water, with a 
tissue paper or fork will be sufficient.
• Rinse aid has spilled into the machine when adding rinse aid. >>> Take care 
that rinse aid is not spilled in the machine when you are filling it. Cl\
ean any 
spilled rinse ait with the help of a tissue paper/towel.
• Lid of the rinse aid reservoir is left open. >>> Make sure that the lid of the 
rinse aid reservoir is closed after adding rinse aid.
Kitchen utensils are broken.
• Dishes are not placed orderly in the machine. >>> Load the dishes as 
described in the user manual.
• Baskets are overloaded.  >>> Do not overload the baskets in excess of their 
capacity.
Water remains in the dishwasher at the end of the programme.
• Filters are clogged. >>> Check if the filter system is clean. Clean the filter 
system regularly as illustrated in section "Cleaning and Care".
• Discharge hose is clogged/blocked. >>> Check the discharge hose. If 
necessary, remove the discharge hose, clear the blockage and insert is as 
illustrated in the user manual.
C If you cannot eliminate the problem although you follow the instructions\
 in 
this section, consult your dealer or the Authorised Service Agent. Never try to 
repair a nonfunctional product yourself. 
EN  
						

							17 7569 0100_YK_(EN)www.beko.com