Black & Decker Pw1300 C Manual

VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO
Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO. 
INSTRUCTION MANUAL
C C C C
o o o o
m m m m
p p p p
a a a a
c c c c
t t t t
       
E E E E
l l l l
e e e e
c c c c
t t t t
r r r r
i i i i
c c c c
       
P P P P
o o o o
w w w w
e e e e
r r r r
       
W W W W
a a a a
ss s s
h h h h
e e e e
r r r r
BEFORE RETURNING THIS PRODUCT 
FOR ANY REASON PLEASE...

2
WARNING:When using this product,
basic precautions should always be
followed, including the following:
1.Read and understand all instructions
before using the product.
2.To reduce the risk of injury, close
supervision is necessary when a product
is used near children.
3.Know how to stop this product and
bleed pressure quickly. Be thoroughly
familiar with the controls.
4.Stay alert - watch what you are doing.
5.Do not operate this product when
fatigued or under the influence of alcohol
or drugs.
6.Keep...

20.Pressure washer is not meant to
pump hot water. Never connect it to a hot
water supply as it will significantly reduce
the life of the pump.
21.Never store the pressure washer
outdoors or where it could freeze. The
pump will be seriously damaged.
22.Discharge residual pressure by
pressing the trigger until no more water
comes out of the nozzle.
CAUTION:Wear appropriate hearing
and respiratory protection during use.
Under some conditions and duration of
use, noise from this product may
contribute to...

Figure 3 - Connect the threaded end of
the Quick Connect adapter (I)to your
garden hose as shown in Fig. 3.
Figure 4- With the quick connect
adapter (I)attached to your garden hose,
pull back on the top section and push
onto the water inlet connector (B)of the
pressure washer, then release.
Figure 5- Connect garden hose to the
cold water source and turn water on full.
The intake water temperature must NOT
exceed 50°C (122°F). The water supply
pressure must NOT exceed 10 bar
(145psi).
4
 
A.Water outlet...

5
CAUTION:The pressure washer must
only be used with clean water; use of
unfiltered water or corrosive chemicals
will damage the pressure washer.
OPERATION
NOTE: Before cleaning any surface, an
inconspicuous area should be cleaned to
test spray pattern and distance for
maximum cleaning results. If painted
surfaces are peeling or chipping, use
extreme caution as pressure washer may
remove the loose paint from the surface.
The PW1300 Pressure Washer is
equipped with automatic delivery flow 
cut-off:
When...

6
YOUR PRESSURE WASHER IS NOW
READY TO USE - PLEASE REVIEW
THE FOLLOWING FOR DETAILS ON
ACCESSORIES APPLICATION.
ACCESSORIES
CAUTION: Before changing
accessories, turn unit off, pull trigger
to release pressure, and activate
safety catch.
•ADJUSTABLE FAN WAND
1.) Insert the fan wand (D) into the gun
wand (E)by pushing and rotating until
the two parts are locked as shown in
Figure A.
2.) To obtain maximum pressure, rotate
the fan wand nozzle in a clockwise
direction as shown in FIgure B. This
narrow...

7
particles to imbed in the surface. When
working on vertical surfaces, it is best to
apply detergent starting at the bottom
and working upwards which will prevent
the detergent from sliding down and
causing streaks.
SHUTDOWN
1.Depress the off switch and unplug the
cord from the outlet.
2.Turn off water at the faucet.
3.Discharge residual pressure by
pressing the trigger until no more water
comes out of the adjustable nozzle.
4.Engage the gun safety catch.
5.Disconnect the garden hose from the
water...

8
SERVICE INFORMATION
Black & Decker offers a full network of
company-owned and authorized service
locations throughout North America. All
Black & Decker Service Centers are
staffed with trained personnel to provide
customers with efficient and reliable
power tool service.
Whether you need technical advice,
repair, or genuine factory replacement
parts, contact the Black & Decker
location nearest you.
To find your local service location, refer
to the yellow page directory under
“Tools—Electric” or call:...

Unit not plugged in.
On/Off switch is in the Off
position.
Wand trigger not being
squeezed.
GFCI tripped.
Water faucet not fully
turned on.
Water inlet filter clogged.
Nozzle worn.
Pump is sucking air.
Water supply restricted.
Not enough inlet water
supply.
Pump is sucking air.
Water inlet filter clogged.
Discharge nozzle is
obstructed.
Detergent container is empty.
Detergent bottle or suction
tube not properly
connected.
Detergent is too thick.
Filter on detergent suction
tube is clogged.
Damaged or...

10
Broken O-ring.
Pump is sucking air.
Loose fittings.
Water seals are damaged
or worn.
Oil seals are damaged or
worn.
Supply voltage below
minimum.
System has residual
pressure.
Voltage loss due to
extension cord.
Cleaner not used for long
periods.Contact B&D Customer Service
Representative at 1-800-544-6986.
Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing trigger gun until a
steady flow of water emerges from the
nozzle.
Check that all fittings are tight....