Candy Cdi 2012e10 S User Instructions

							20
EN 50242 place load
Capacity with pans and dishes
Water supply pressure 
Fuse
Power input
Supply voltage12
8 persons
Min. 0,08 - Max 0,8 MPa
(see rating plate)
(see rating plate)
(see rating plate)DESCRIPTION OF THE CONTROL
TECHNICAL DATA: DIMENSIONS:Height
Depth 
Width 
Depth with door open
cm
cm
cm
cm82 ÷ 88,5
55
59,8
11 7
A
"ON/OFF" button 
B
PROGRAMME DESCRIPTION 
C
"PROGRAMS" buttons
D 
"HALF LOAD" button
E
"DELAY START" button 
F 
"PROGRAM STATUS" LEDs/
"DELAY START" time LEDs
G
"OPTION SELECTION" LED
H 
"PROGRAM SELECTION" LEDs
I 
"SALT EMPTY" light
DBA
HC
GI
F
E
21
PROGRAM SELECTION 
AND SPECIAL FUNCTIONS(Use in conjunction with programme guide) Program settings■Open the door and place dirty dishes
inside the appliance. 
■Press the "ON/OFF"button       .           
■After pressing the "ON/OFF" button.
The LED for the factory set is
recommended”(which is ideal for full
load daily use) or the LED for the "Auto’
Memory" program (see below) will blink. 
IMPORTANT
The dishwasher has two very practical
functions:
- the recommended program
(            ) for quick and sure selection; 
- the Auto’ Memory, function which
saves a program used at least 3
times consecutively so that if you
regularly use the same washing cycle
each time you do not have to
continually set the program thereby
saving time and effort.
■If you wish to select an option, press the
option button (the corresponding LED
will light).
The option button must be pressed
BEFORE the program starts for the
option to be accepted.
■To choose another program, press the
corresponding button (the relevant LED
will blink to confirm the selection).
IMPORTANT
To select the "COLD RINSE" program,
simultaneously press the "RAPID"
program button and "HALF LOAD"
option button (the relevant LEDs will
blink, confirming the selection).■To start the program, press the selected
program button again to confirm. The
relevant LED will stop blinking and
remain on and, when the door is shut,
the program will start automatically.
IMPORTANT
To confirm the “COLD RINSE” program,
simultaneously press the “RAPID”
program button and the “HALF
LOAD” option button (the relevant
LEDs will stop blinking and remain
on to confirm the selection).
Program interruptionOpening the door when a program is
running is not recommended especially
during the main washing and final hot rinse
phases. However, if the door is opened
while a program is running (for example,
to add dishes) the machine stops
automatically.
Close the door, without pressing any
buttons. The cycle will start from where it
left off (if it is necessary, the appliance
will make a short thermal anti-shock
programme before).Changing a running programProceed as follows to change or cancel a
running program:
■Hold down the current program button
(with the LED on) for at least 3seconds.
The program LEDs (except for the
"RAPID"program LED) will start to blink.
WARNING!
Don't switch off the dishwasher,
before the end of the water discharge. 
 
						

							22
■Close the door to allow the water to be
discharged.
The running program will be cancelled
and the LED for the“recommended”
program or the LED for the program that
was used at least 3 times consecutively
will start to blink.
IMPORTANT 
To cancel the "COLD RINSE" program,
simultaneously hold down the
"RAPID" program button and "HALF
LOAD" option button.
■At this point a new program can be set.
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser. 
If necessary, top up the dispenser.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off (if
it is necessary, the appliance will make
a short thermal anti-shock programme
before).Program operations  When a program is running the relevant
LED will remain on and the 3“PROGRAM
STATUS” LEDs ("WASH"    , "RINSE"    ,
and "DRY"    ) will light singularly and in
sequenceto indicate the current phase.Program endThe “PROGRAM STATUS”LEDs will turn
off and the LED for the factory set is
recommended”or the LED for the Auto’
Memory program will blink to indicate that
the cycle has ended. 
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF"button or dishes can be loaded
for new cycle.
Option button"HALF LOAD" button
By using this option, it is possible to wash a
smaller quantity of crockery: you should load
only the upper basket for dishes and place
cutlery in the tray in the bottom basket.
This reduces water and energy consumption
and requires a smaller quantity of detergent.
IMPORTANT 
This button MUST be set BEFORE the
program starts.
"DELAY START" button 
Dishwasher start time can be set with this
button, delaying the start by 3, 6 or 9 hours.
Proceed as follows to set a delayed start:
■ Press the "DELAY START"button (each
time the button is pressed the start
will be delayed by 3, 6 or 9 hours
respectively and the corresponding time
LED will light).
■ To start countdown, press the selected
program button (the relevant LED will
stop blinking and remain on, while the
set time LED will start to blink).
If a 9 hour delay is set, countdown will be
displayed by the6hLED after 3 hours and
the 3hLED after 6 hours.
At the end of the last 3 hours (at the end
of countdown) the 3hLED will stop
blinking and remain on to indicate the
washing phase and the program will start
automatically.
If countdown has not ended, whereby
the program has not yet started, it is
possible to change or cancel the delayed
start and select another program or to
select/unselect the option button, proceeding
as follows:
■ Hold down the selected program button
for at least 5seconds (the corresponding
LED will start to blink while the set time
LED will stop blinking and remain on). 
■Press the"DELAY START" button to
set another delayed start time (the
corresponding time LED will turn on) or
cancel delayed start (corresponding time
LEDs will all turn off).
■Anew program can be set after a
delayed time has been changed or
cancelled (the corresponding LED will
stop blinking and remain on) or an option
button has selected or deselected. 
23
Fault signals If malfunctions or faults occur when a
program is running the LED that
corresponds to the selected cycle (2 LEDs
for the "COLD RINSE" program) will blink
rapidly.
In this case, turn the dishwasher off by
pressing the"ON/OFF" button. After
checking to make sure the water intel hose
tap is open, that the drain hose is not bent
and that the siphon or filters are not
clogged, set the selected program again. If
the anomaly persists, contact Customer
Service.IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically empty any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, it is
recommended not to move or to tilt
the dishwasher during operation.
If it is necessary to move or to tilt the
dishwasher, first make sure the
washing cycle is finished and that no
water is left in the tank.
 
						

							25
24
5
•
• • ••••• ••••
• ••
50°C
32
•
•
• •
65°C
95
•
•
YES
75°C
120
•
••
•
••••
45°C
140
• • •
• •
YES
•
•
• • • •
•
YES
YES
YES YES
Programme PROGRAMME SELECTION
YES
Check list  
Avarage
durationin minutes
Special function
buttons 
available
Detergent for soaking
(Prewash)
Detergent for washing
Clean filter
Check rinse aid 
dispenser
Check salt container
Hot pre-wash
Cold pre-wash
Main wash
First cold rinse
Second cold rinse
Hot rinse with rinse aid
With cold water (15°C)
-Tolerance ± 10%-
"DELAY START" button
"HALF LOAD" button
Programme contents
Description
YES
Wash with prewash 
If setting the HYGIENICwash programme, a second dose of about 20 g of detergent
(1 table-spoon) must be added directly in the machine.(“RECOMMENDED” PROGRAMME)
Once a day - for normal soiled pans and any
other items that have been left all day for
washing. 
Once a day - for heavily soiled pans and any
other items that have been left all day for
washing.
Energy Saving Programme suitable for
normal soiled items. Using detergents with
enzyme.
Programme standardised to EN 50242.
Quick wash for dishes which are to be
washed immediately after the meal. Wash
load of 4/6 persons.
Short cold pre-wash for items that are stored
in the dishwasher until you are ready to
wash a full load.
UNIVERSALHYGIENIC
ECO
RAPID 32’ 
COLD RINSE
+
 
						

							27
N.B.: Should any of the situations occur and should the machine give a bad wash performance,
it is necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the
deposits which a second wash in the machine would not be able to remove.
If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher.
This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee. 
This information will make it possible to take more effective action more quickly.
The manufacturers decline any responsibility for any printing mistakes in this instruction booklet.
They also reserve the right to modify their own appliances as necessary without altering the
essential characteristics.FAULT CAUSE REMEDY
7 - Load of dishes is only 
partially washed 
8 - Presence of white spots 
on dishes
9 - Noise during wash
10 - The dishes are not 
completely drySee causes for no. 5
Bottom of saucepans have not
been washed well
Edge of saucepans have not 
been washed well
Spray arms are partially blocked
The dishes have not been 
properly loaded
The end of the outlet hose is in
the water
The incorrect amount of 
detergent has been measured
out; the detergent is old and hard
The wash programme is not 
thorough enough
The lower basket dishes have
not been washed
Water is too hard
The dishes knock against one
another
The revolving arms knock against
the dishes
Inadequate air flowCheck
Burnt on food remains must 
be soaked before putting pans
in dishwasher
Reposition saucepans
Remove spray arms by
unscrewing ring nuts clockwise
and wash under running water
Do not place the dishes too 
closely together
The end of the outlet hose 
must not come into contact 
with the outflow water
Increase the measure 
according to how dirty the
dishes are and change detergent
Choose a more vigorous 
programme
Depress half load button
Check salt and rinse aid level
and regulate amount. 
Should the fault persist, 
Contact Service Centre
Re-check loading of dishes in
the basket
Again re-check loading
Leave the dishwasher door ajar
at the end of the wash program
to allow the dishes to dry naturally
IDENTIFYING MINOR FAULTSShould  the  dishwasher  fail  to  operate,  before  contacting  the  Service  Centre, make
the following checks:
26 FAULT CAUSE REMEDY
1 - Machine completely dead 
2 - Machine does not 
draw water
3 - Machine does not 
discharge water
4 - Machine discharges 
water continuously
5 - Spray arms are not heard
to rotate
6 - On electronic appliances
without a display: one or
more LED flashing quickly.Plug is not connected to wall
socket
O/I button has not been pressed
Door is open
No electricity
See causes for no. 1
Water tap is turned off
Programme selector is not at
correct position
The inlet hose is bent
The inlet hose filter is not 
correctly connected
Filter is dirty
Outlet hose is kinked
The outlet hose extension is
not correctly connected
The outlet connection on the
wall is pointing downwards not
upwards
Position of outlet hose is too
low
Excessive amount of detergent
Item prevents arms from rotating
Plate and cup filter very dirty
Water inlet tap turned offConnect electric plug
Press button
Close door
Check the fuse in the plug and 
the electricity supply
Check
Turn water tap on
Turn programme selector to
correct position
Eliminate the bends in the hose
Clean the filter at the end of the
hose
Clean filter 
Straighten outlet hose
Follow the instructions for 
connecting the outlet hose
carefully
Call a qualified technician
Lift outlet hose to at least 40 cm
above floor level
Reduce amount of detergent 
Use suitable detergent
Check
Clean plate and cup filter
Switch off the appliance.
Turn on the tap.
Re-set the cycle.
 
						

							The manufacturer declines all responsibility in the event of any printing mistakes in this
booklet. The manufacturer also reserves the right to make appropriate modifications to
its products without changing the essential characteristics.
 
						

							04.07- 41012911 - Printed in Italy - Imprimé en ItalieEN