Cannon Canon Allinone Mp C545 User Manual

2-16Paper Handling Chapter 2
Using Canon’s Specialty Papers
This section provides guidelines for printing on Canon’s specialty papers and 
describes special procedures required for high resolution paper, fabric sheets, and 
banner paper.
Specialty Paper Guidelines
Follow these guidelines:
❑When feeding transparencies, remove each sheet after it is delivered, being 
careful not to touch the document tray. Do not allow transparency sheets to 
stack up in the output tray. (Should you dirty the document tray...

Chapter 2 Paper Handling2-17
Paper Handling
❑When loading transparencies, insert one sheet of plain paper as the last sheet 
in the stack.
❑Do not leave film in the multi-purpose tray for long periods of time. Dust and 
dirt may accumulate on the film resulting in spotty printing.
❑To avoid smudging caused by fingerprints, use a pair of thin cloth gloves while 
loading and handling film.
❑To avoid fading, do not expose printed film to prolonged sunlight.
❑Store unused papers and films flat. Do not remove papers...

2-18Paper Handling Chapter 2
1. Raise both paper output guides to a vertical position.
2. When you finish printing on High Resolution Paper or Banner Paper, lower 
the paper output guides.
Using the Cleaning Sheet
Canon’s High Resolution Paper is designed for high quality printing. This paper is 
specially coated to produce delicate color output.
After using a package of High Resolution Paper (200 sheets) you need to use 
the cleaning sheet, provided with the paper, to remove paper dust from the unit’s...

Chapter 2 Paper Handling2-19
Paper Handling
2. Remove the covers from the two pieces of tape on the cleaning sheet.
3. With the sticky side out (toward you) and down (going into the multi-purpose 
tray), insert the sheet into the multi-purpose tray until it stops, so that the 
right edge of the sheet is aligned with the right side of the multi-purpose tray. 
Then slide the paper guide snugly against the left edge of the  cleaning sheet. To avoid paper jams, smearing, and other problems, never open the...

2-20Paper Handling Chapter 2
4. Open the document tray.
.
5. Press Function.
6. Press 
Cleaning.
NOZZLE CHECK
Function
10
Cleaning 

Chapter 2 Paper Handling2-21
Paper Handling
7. Use d or u to select ROLLER CLEANING.
8. Press 
Set.
The MultiPASS feeds the cleaning sheet into the MultiPASS and cleans the 
rollers.
Printing on Banner Paper
Banner paper is a continuous sheet of paper with perforations at equal distances 
along its length, where it can be cut to the length required. For best results, use 
Canon’s Banner Paper.
To set up a print job on banner paper, you must decide on the number of sheets 
you need. The banner can be a...

2-22Paper Handling Chapter 2
1. Place the MultiPASS near the edge of a table so that the paper can flow over the 
edge as it exits the unit.
❑Make sure the paper rest is extended.
2. Make sure the paper thickness lever is set to the left  m  (see page 2-6).
To avoid paper jams, smearing, and other problems, never open the printer 
cover to set the paper thickness lever while the MultiPASS is printing.
Ink
C
a
rtrid
g
eBCl-21
ColorM
a
de 
 in
J
a
pa
nI
n
k
C
a
r
t
r
i
d
g
eB
C
l
-2
1
B
la
c
kMade  in
Japan
c 

Chapter 2 Paper Handling2-23
Paper Handling
3. Raise both paper output guides to a vertical position.
4. Cut the banner paper along one of the perforations to the length required.
❑Your banner can be up to six sheets (66 inches/1676 mm) long.
5. Place the banner paper behind the unit on a flat surface.
6. Gently fold along the perforations between the first and second sheets. 

2-24Paper Handling Chapter 2
7. Insert the first sheet into the multi-purpose tray until it stops, so that the right 
edge of the sheet is aligned with the right side of the multi-purpose tray.
❑Make sure the sheets behind the unit are aligned with the multi-purpose 
tray. 

Chapter 2 Paper Handling2-25
Paper Handling
8. Slide the paper guide against the left edge of the sheet, leaving a 0.04 inch (1 
mm) gap between the paper guide and the edge of the sheet.
❑Make sure the sheet is under the tabs on the multi-purpose tray.
9. Your MultiPASS is now ready to print. Set your Macintosh to print on the 
banner paper.
❑Allow the paper to flow over the edge of the table as it exits the MultiPASS.