Canon Fax L2000ip User Guide

Setting the Paper Size for the Paper Cassettes2-15
2
Getting Started
6Press   (Stop) to return to the Standby mode.
 

Using the MP Tray2-16
Getting Started
2
Using the MP Tray
The MP (Multi-Purpose) tray can hold standard A or B series paper or inch-size paper, non-
standard size paper, envelopes, label sheets or transparencies, and can hold up to 
approximately 100 sheets of paper (80 g/m
2). For details on the types of paper you can set on 
the MP tray, see “Available Paper Stock,” on p. 2-27. To use the MP tray as one of the input 
trays, you need to set MP TRAY to ‘USE’ in the PAPER SETTINGS menu. (See Chapter 5,...

Using the MP Tray2-17
2
Getting Started
 Remove the label sheets from the output tray as they are printed to prevent them from sticking 
together.
 Do not use the following label sheets in the MP tray:
- Labels that are separating from the backing sheet or partially used label sheets
- Coated labels which can be easily separated from the backing sheet
- Label sheets with sticky paste exposed
 Do not set the paper guides so tight that the paper stack bends.
 Do not set the paper guides so loose that...

Using the MP Tray2-18
Getting Started
2
 Do not place the paper into the tray at an angle.
 Do not load fanned out paper. Make sure the edges of the paper stack are evenly aligned when 
loading.
NOTE
 If a printed page comes out of the machine all curled up, you can correct the problem by turning over 
the paper stack in the MP tray so that the bottom sheet in the stack is now at the top.
 If the leading edge of the paper is curled, straighten it out as much as possible before loading it into 
the...

Using the MP Tray2-19
2
Getting Started
1Open the MP tray.
2Pull out the extension tray using the center grip a, then flip open 
the support tray b.
3Before you load paper into the MP tray, tap the edges of the stack 
to make sure the leading edge and sides of the stack are even.
2
1
 

Using the MP Tray2-20
Getting Started
2
NOTE
 The MP tray holds approximately 100 sheets of paper.
4Insert the paper stack as far as it will go into the main unit, with 
the side you want to print on facing up, and the top edge of the 
paper heading into the main unit first.
5Adjust the paper guides to the size of the paper. 
 

Using the MP Tray2-21
2
Getting Started
IMPORTANT
 Make sure that the leading edge of the paper is inserted all the way into the MP tray until 
it stops so that it is below the paper feed roller. The paper sensor for the MP tray is 
located to the right of the paper feed roller, when viewed from the front of the machine.
 Please note the following points when loading small size paper:
- If the paper is not loaded correctly, the paper is not detected by the machine, and a 
message appears asking you to...

Using the MP Tray2-22
Getting Started
2
- Make sure that the leading edge of the paper is resting against the paper sensor.
 To avoid damaging the MP tray, close it when it is not in use. Remove and store any 
remaining print media. Fold up the support tray, and gently push in the extension tray 
before closing the MP tray.
●To load envelopes into the MP Tray:
❏Take five envelopes, loosen them as shown, and stack them together.
❏Place the envelopes on a clean, level surface, and press all the way around...

Using the MP Tray2-23
2
Getting Started
IMPORTANT
 Take particular care to position the envelopes in the direction that they will be fed.
❏Hold down the corners of the envelopes firmly as shown in the illustration 
below, so that they and the sealed or glued portion stay flat.
IMPORTANT
 Do not print on the underside of the envelopes (the side with the flap).
 If the envelopes become filled with air, flatten them by hand before loading them into the 
MP tray.
❏Load the envelopes, as shown below.
Flap...

Using the MP Tray2-24
Getting Started
2
IMPORTANT
 Depending on the paper type or condition of the envelopes, the printing quality may 
deteriorate or a paper jam may occur. In such a case, it is recommended to change the 
type of envelopes.