Canon Lv-7265, Lv-7260, Lv-x7 Multimedia Projector Users Manual

22
2. Installation and Connections
M
ENU
B
AC
KKE
YSTONE
WARNING    POWER AUTO PCINPUT
VOL-VOL+
LAMP
AUDIO INAUDIO OUTANALOG IN-1
DIGITAL IN /
ANALOG IN-2
S-VIDEO
INVIDEO
INSERVICE PORTR LAUDIO IN
Connecting the Supplied Power Cord
Connect the supplied power cord to the projector.
First connect the supplied power cord's two-pin plug to the AC IN of the projector, and then connect the other plug 
of the supplied power cord in the wall outlet.
Make sure that the prongs are fully inserted into 
both the...

23
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.
❶
 Turning on the Projector
NOTE:
•  The projector has two power switches: a main power switch and a POWER button.
•   When plugging in or unplugging the supplied power cord, make sure that the main power switch is pushed to the off (
) po-
sition. Failure to do so may cause damage to the projector.
WARNING
LAMP
    1.  To turn on the main power to the projector,...

24
VOL-VOL+
MENU
BACK
KEYSTONE
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you fi rst turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select 
one of the 21 menu languages.
To select a menu language, follow these steps:
1.  Use the SELECT    or  button to select one 
of the 21 languages for the menu.POWER
BACK INPUT IMAGE
ASPECT
INFO.
MENUNO SHOW
AUTO PC
2.  Press the OK button to execute the selection....

25
3. Projecting an Image (Basic Operation)
❷
 Selecting a Source
Selecting the computer or video source
WER 
AUTO PC
INPUT
VOL-
POWER
BACK INPUT IMAGE
ASPECT
INFO.
MENUNO SHOW
AUTO PC
NOTE: Turn on the computer or video source equipment connected to the pro-
jector.
Selecting from INPUT List
Press and quickly release the INPUT button on the projector cabinet 
to display the Source list. Each time the INPUT button is pressed, the 
input source will change as follows: “Computer 1”, “Computer 2 (Digi-...

26
3. Projecting an Image (Basic Operation)
Place your projector on a fl at level surface and ensure that the projector is 
square to the screen.
Lift the front edge of the projector to center the image vertically.
•  If the projected image does not appear square to the screen then use 
the Keystone feature for proper adjustment. See page 
28 to 29.
❸
 Adjusting the Picture Size and Position
Adjust the Tilt Foot
1.  Lift the front edge of the projector.
CAUTION:
Do not try to touch the ventilation outlet...

27
3. Projecting an Image (Basic Operation)
Focus
Use the FOCUS ring to obtain the best 
focus.
Zoom
Use the ZOOM lever to fi nely adjust the im-
age size on the screen. 

28
3. Projecting an Image (Basic Operation)
❹
 Correcting Keystone Distortion
Correcting Keystone Distortion
If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following
steps to correct keystone distortion
 
NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
NOTE: The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection.
NOTE: Turning off the projector...

29
3. Projecting an Image (Basic Operation)
Adjusting with the Auto Keystone Function (LV-7265 only)
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No 
special operation required. Just put the projector on a fl at surface.
TIP: Even when the menu setting for [Auto keystone] is turned on, [Keystone adjustment] can be adjusted manually.
To turn on [Auto keystone], proceed the following steps.
1.  Press the MENU button
  The menu will be...

30
3. Projecting an Image (Basic Operation)
❺
 Automatically Optimizing on RGB Image
Adjusting the Image Using Auto PC adjustment
Optimizing an RGB image automatically.
Press the AUTO PC button to optimize an RGB image automatically.
[Poor picture]
[Normal picture]
AUTO PC
OWER 
AUTO PC
INPUT
VOL-
POWER
BACK INPUT IMAGE
ASPECT
INFO.
MENUNO SHOW
AUTO PC
Press the AUTO PC button to fi ne-tune the computer image or to remove any vertical banding that might appear 
and to reduce video noise, dot interference...

31
❼
 Turning off the Projector
To turn off the projector:
3. Projecting an Image (Basic Operation)
WARNING    POWER 
LAMP
POWER
INPUT IMAGE
ASPECT
INFO.
MENUNO SHOW
AUTO PC1.  Press the POWER button on the projector cabinet or 
the remote control. The “Push POWER button again 
to turn off power.” message will appear.
WARNING
LAMP
    WARNING
LAMP
WARNING
LAMP
        
Power On Fan running Standby
Steady 
green lightBlinking 
orange lightSteady 
orange light
CAUTION:
Parts of the projector will become...