Canon network camera VBR13 User Manual

Camera Setup
2
31
If you select [Easy Installation], confirm the software that will be installed and click [Next].
If you select [Custom Installation], select the  software to be installed and click [Next].
The User License Agreement screen is displayed.
4Select the installation method.
5Confirm or select the software that will be installed. 

32
Installation starts.
The Camera Management Tool icon and Recorded Video Utility icon will be displayed on the desktop.
6Read through the user license agreement and click [Yes] if you accept it.
7Click [Exit] or [Reboot]. 

Camera Setup
2
33
Camera configuration and operation may be blocked, depending on the security functions of the operating system and web 
browser.
Change or check security settings beforehand.
Checking Firewall Settings
To use the Camera Management Tool on computers where Windows Firewall is enabled, you may need to add the Camera 
Management Tool as an application a llowed to communicate via the firewall.
Note
Even if you do not perform the following steps, you can still ad d the Camera Management Tool...

34
Adding the Camera IP Address as a Trusted Site
When the security level for internet sites and intranet sites is se t to [High], it is necessary to add the IP address of the 
camera to the list of trusted sites.
Note
Set the camera IP address with the Camera Management Tool (P. 40).
3Click [Change settings] > [Allow another app].
4Select [Camera Management Tool] and click [Add].
1Click [Network and Internet] > [Int ernet Options] in [Control Panel].
2Click the [Security] tab. 

Camera Setup
2
35
The [Trusted sites] dialog box is displayed.
Note
 Clear the [Require server verification (https:) for  all sites in this zone] checkbox if it is selected.
The camera’s IP address will be added to the [Websites] list.
 You can add IP addresses for multiple cameras by  using a wildcard (*) when entering the IP address.
For example, if you enter “192.160.1.*”, all  cameras that share the “192.160.1” portion of the address will be added as trusted  
sites.
Settings When Using Windows...

36
Security Settings When Using an SSL/TLS Connection
When an SSL/TLS connection to the camera is made from  a web browser (Internet Explorer 9/10/11) in Windows 
Server 2008/Windows Server 2012, the fo llowing operations may cause the blocked content dialog box to display, 
and prevent further operation.
 The launching of the Viewer and the Setting Page
 Audio reception from the Viewer
This occurs when Internet Explorer Enhanc ed Security Configuration (IE ESC) is enabled in Internet Explorer 9/10/11....

Camera Setup
2
37
The [Audio Service Not Running] dialog box is displayed.
The [Sound] dialog box is displayed.
If no audio device is installed, refer to your computer manual.
2Click [Sound].
3Click [Yes].
4Click the [Playback] tab to confirm that an audio device has been installed. 

38
To use a camera, it is necessary to first set the administrator account for the camera, then configure the network settings, 
and then connect the camera and computer  via the network. Use the Camera Management Tool to configure these settings.
This section describes the procedure for configuring the initial  settings for a camera with the factory default settings, such 
as the administrator account  and the network settings using the Camera Management Tool.
Note
For details on using the Camera...

Camera Setup
2
39
The [Search Cameras] dialog box is displayed.
Detected cameras will be displayed in the camera list.
When a dialog indicating that a camera requiring an administrator to be registered has been found, click [OK].
Registering the Administrator Account
Register the administrator account for cameras with  [Admin Required] displayed for [Connection Status].
The [Register Administrator Account] dialog box is displayed.
1Click the [Search Cameras] icon.
2Click [Search].
1Select a camera in...

40
(1) [Administrator Name]Enter the administrator name using only alphanu meric characters, hyphens, and underscores.
(2) [Administrator Password] Enter the Admini strator Password.
(3) [Confirm Administrator Password] Enter the administrator pass word again for confirmation.
A dialog confirming whether you want  to reboot the camera is displayed.
Click [OK] to reboot the camera.
[Connection Status] will change to [Conne ctable] after the camera is rebooted.
Setting up Networks
Configure the network...