Canon network camera VBS905F User Manual

[Video] Setting Video Size, Quality and Frame Rate
51
Setting Page
3
(2) [Bit Rate Control] 
Select [Do not use bit rate control] or [Use bit rate 
control].
Select [Use bit rate control] when [Video Format] 
under [Upload] is set to [H.264(1)] or when [Video 
Format] under [Memory Card] is set to [H.264(1)].
(3) [Target Bit Rate (kbps)] 
If [Use bit rate control] is selected in (2), select a 
desired target bit rate from the 17 levels from [64] to 
[16384].
(4) [Video Quality] 
If [Do not use bit rate...

52
(4) [Time display] 
Select whether to enable time display over video. If 
[Enable] is selected, display time information will be 
displayed over video. 
(5) [Position of time display] 
Select [Upper left], [Upper right], [Lower left] or 
[Lower right] for the position of time display 
information. 
(6) [Text display] 
Select [Display nothing], [Display designated string] 
or [Display camera name] for the text string to display 
over video. 
If [Display designated string] is selected, the [Text 
string...

53
3
Setting Page
RTP Server
(1) [RTP]
Set RTP to [Disable] or [Enable].
(2) [RTSP Authentication Method]
Set the RTSP authentication method to [Basic 
Authentication], [Digest Authentication], or [No 
Authentication].
(3) [RTSP Port]
Set the RTSP port number to 554 or in the range of 
1024 to 65535.
Normally [554] (factory default setting) is used.
Audio Multicast
(1) [Multicast Address]
Set the multicast address for audio transmission in the 
range 224.0.0.0 to 239.255.255.255 (IPv4) or an 
address...

54
distribution is confined to the local segment only and 
cannot be distributed by the router.
(6) [Audio Transmission]
Set RTP streaming audio transmission to [Disable] or 
[Enable].
Note
 RTP stream URL
rtsp://IP_address:port_number/rtpstream/config1(~5)=r|u|m
[=r|u|m] is optional and can be omitted. If specified, specify 
only one option.
r: Requests RTP over TCP
u: Requests RTP over UDP
m: Requests multicast
Example: RTP streaming 1 request using RTP over TCP...

55
3
Setting Page
General Upload
(1) [Upload] 
Select [Upload Disabled], [HTTP Upload] or [FTP 
Upload] for the upload method.
(2) [Video Format]
Select the [JPEG] or [H.264(1)] format for video you 
want to upload. 
If [H.264(1)] is selected, video is uploaded with the 
settings defined under [Video] > [H.264(1)] (p. 50).
 [H.264(2)] cannot be used.
(3) [Frame Rate] 
Enter the maximum frame rate of video to be 
uploaded. This setting can only be made when 
[JPEG] is selected for [Video Format].
(4)...

56
– From the Intelligent Function Setting Tool [Event] tab > 
disable [ON Event Operation], [OFF Event Operation] or 
[Detected mode Operation] (p. 110). 
– If [External Device Input Event] is enabled, disable [Active 
Event Operation], [Inactive Event Operation], or [Ongoing 
Active Event Operation] (p. 61). 
– If [Timer Event] is enabled, increase the value in [Repeat 
Interval] (p. 62). 
HTTP Upload
The HTTP upload function sends notifications via HTTP or 
via HTTP with attached videos, depending on...

[Upload] Setting HTTP/FTP Upload and E-mail Notification
57
Setting Page
3
[User Setting] 
Video is uploaded according to the file naming 
method specified in [Subdirectory Name to Create] 
and [File Name to Create]. 
[Subdirectory Name to Create], [File Name to 
Create] 
If file naming is set to [User Setting], enter the 
subdirectory name to be created as well as the 
name of the created file (using up to 127 
characters). Parameters can be specified in the 
entry with the “%” character (p. 152).
(7)...

58
Video Server
(1) [Maximum Number of Clients] 
Set the maximum number of clients that can be 
connected to the camera at the same time. Up to 30 
clients can be set. 
If 0 is set, connection is prohibited except for the 
Administrator. 
(2) [Camera Control Queue Length] 
Set the maximum queue length for clients requesting 
camera control privilege from the viewer. The 
maximum number is 30. Enter an integer from 0 to 30. 
If 0 is set, camera control is prohibited except for the 
Administrator. 
(3)...

[Server] Setting the Video Server, Audio Server, HTTP Server, FTP Server and WS-Security
59
Setting Page
3
HTTP Server
(1) [Authentication Method] 
Set the authentication method used with the HTTP 
server to [Basic Authentication] or [Digest 
Authentication]. 
(2) [HTTP Port] 
Set the HTTP port number to 80 or in the range of 
1024 to 65535. 
Normally [80] (factory default setting) is used. 
(3) [HTTPS Port] 
Set the HTTPS port number to 443 or in the range of 
1024 to 65535. 
Normally [443] (factory...

60
Video Record Setting
(1) [Video Record Action]
Select the destination of a video recorded when an 
event occurs. To record to a server selected on the 
[Upload] in the setting page, select [Upload] and to 
record to a memory card inserted in the camera, 
select [Record to Memory Card].
Note
The size and format of video recorded according to the [Video 
Record Action] settings are as follows:
Settings must be made in the above setting page to make 
an actual video recording.Volume Detection
(1) [Volume...