Canon scanner imageFORMULA ScanFront 300 User Manual

2-4
Chapter 2   Handling
2.Preparing the Scanner
When placing a document in the scanner, pull out the document eject tray so that it matches the size of the document, and then move 
the feed selection lever to the appropriate position for the desired feed method (Page Separation ON or OFF) for the document.
❏Preparing the Document Feed Tray and 
Eject Tray
Prepare the trays in accordance with the type of document. 
1.Open the document feed tray a.
2.Open the document eject tray b.
Hint
Open the center...

2-5
Chapter 2   Handling
❏Feed Selection Lever
Change the position of the lever to the desired feed method 
for the document.
Page Separation ON
Move the lever downward to separate a stack of documents 
one page at a time in order to continuously feed the 
documents.
Page Separation OFF
Move the lever upward to feed a document with multiple 
pages attached together such as an invoice one page at a 
time without separating the pages. 
IMPORTANT
Moving the lever upward (Page Separation OFF) and then...

2-6
Chapter 2   Handling
3.Placing Documents
When placing documents into the scanner, place them face down into the tray with the top edge of the document at the bottom of 
tray. 
❏Placing a Document
Follow the procedure below to place a document. 
1.Adjust the document guides to be wider than the 
width of the document. 
2.Fan the document to offset the pages so that the top 
edge of the first page is the lowest. 
3.Place the document face down with its top edge at 
the bottom of the tray.
4.Adjust the...

2-7
Chapter 2   Handling
IMPORTANT
Make sure that document stacks placed in the feed tray do not 
exceed the document guides.
The number of sheets that you can place in the scanner at 
one time varies by paper size as follows.
Legal/A4 Size or Smaller: 
50 sheets (stack 5 mm thick) or less
Sizes Larger than Legal/A4: 
30 sheets (stacks 3 mm thick) or less
❏Placing a Folded Document
Folio Scan enables you to scan documents that are larger 
than Legal/A4 and therefore do not fit in the feeder. (The...

2-8
Chapter 2   Handling
❏Placing a Card
When you want to scan a card, follow the procedure below 
to place the card. 
1.Move the feed selection lever upward (OFF). 
IMPORTANT
When scanning cards, set the feed selection lever to OFF and 
make sure to scan the cards one at a time. 
2.Adjust the document guides to match the width of the 
card.
3.Place the card face down with the top edge at the 
bottom of the tray.
CAUTION
 A card placed into the document feed tray in the portrait 
orientation may not be...

2-9
Chapter 2   Handling
4.Clearing a Paper Jam or Double Feed Error
When a paper jam or double feed error is detected, feeding and scanning stops.
1.Check the displayed message.
If a paper jam or double feed error is detected at the first 
page of a document, the following messages appear.
Hint
 If you press [Complete], the display returns to the previous 
screen.
 If you want to continue scanning, reset the document before 
progressing with screen operations. Press [Continue] to 
resume scanning.
If a...

2-10
Chapter 2   Handling
IMPORTANT
When the message above is displayed and the scanner 
transitions to Low Power Mode, all of the data scanned up until 
that point is discarded. (See “Low Power Mode” on p. 6-31.)
2.Remove the scanned documents from the document 
eject tray, and any documents remaining in the 
document feed tray.
3.Pull the lock lever toward you and then fully open the 
panel unit.
CAUTION
The open/close movement of the panel unit is linked to the up/
down movement of the document eject...

2-11
Chapter 2   Handling
5.Fingerprint Sensor (ScanFront 300P)
The ScanFront 300P is equipped with a fingerprint sensor for registering fingerprints and authenticating users. 
The fingerprint sensor is a precision component. Be careful when handling this sensor. 
❏Cautions for Handling the Fingerprint 
Sensor
 
●The following actions may damage the fingerprint 
sensor or cause it to malfunction. Read this 
information carefully to avoid damaging the 
sensor.
– Dropping an object on the fingerprint...

2-12
Chapter 2   Handling
❏Fingerprint Authentication
●Follow the procedure below to use fingerprint 
registration and authentication. 
1. Align the first joint of a finger on the sensor and 
press the finger on the fingerprint sensor. 
2. Keep the finger pressed while slowly sliding it 
straight at a constant speed to scan the 
fingerprint. 
 
●Fingerprint authentication uses the unique 
information of fingerprints. The fingerprint 
authentication function may not work properly for a 
finger with a...

Chapter 3   ScanFront Setup
1. Before Setting Up the Scanner ........................ 3-2
Installation Location ..............................................3-2
Connecting the AC Adapter ..................................3-3
Connecting the Network Cable .............................3-3
2. Turning the Power ON and OFF ...................... 3-4
Turning the Power ON ..........................................3-4
Turning the Power OFF.........................................3-4
3. Configuring the Scanner...