Casio Projector XJ-H1600 XJ-H1650 User Manual

							61
zSee the “Command List” for details about command names and settings.
zAll commands use ASCII characters and decimal format integers.
zThe projector will return a question mark (?) when it is sent a command it cannot recognize. Also, 
any command that attempts to set a value that is outside the applicable allowable range will be 
ignored.
zIf the projector is performing a process initiated by a previously sent command, a projector key 
operation, or a remote controller key operation, send of the next command must wait until the 
projector completes the previous process.
Command List
zOnly the following functions are supported while the projector is turned off. Do not try to send any 
other command to the projector.
zInput of a valid signal must be in progress in order to use a command to turn on blank screen or 
change the aspect ratio.
R: Read enabled   W: Write enabled zPower on/off: Read
zPower on: Write
zGet light time: Read
FunctionCommand 
NameRWSetting Range
Power On/Off:PWR RW 0: Off, 1: On
Input Switching: 0:Switches the input source to the 
COMPUTER 1 terminal and changes the 
COMPUTER 1 terminal setting to RGB.
1:Switches the input source to 
COMPUTER 1 terminal and changes the 
COMPUTER 1 terminal setting to 
component.
2:Switches the input source to Video.
3:Switches the input source to the 
COMPUTER 2 terminal and changes the 
COMPUTER 2 terminal setting to RGB.
4:Switches the input source to 
COMPUTER 2 terminal and changes the 
COMPUTER 2 terminal setting to 
component.
5:Switches the input source to USB. This 
setting is supported only when the 
projector is equipped with a USB function 
and the USB application is running.
6:Switches the input source to 
COMPUTER 1 terminal and changes the 
COMPUTER 1 terminal setting to Auto.
7:Switches the input source to HDMI.
9:Switches the input source to S-video.
10:Switches the input source to 
COMPUTER 2 terminal and changes the 
COMPUTER 2 terminal setting to Auto.SRC RW 0: RGB1, 1: Component1,
2: Video, 3: RGB2, 
4: Component2, 5: USB,
6: Auto1 (RGB/Component),
7: HDMI, 9: S-video, 
10: Auto2 (RGB/Component)
Blank Screen: Switches the blank screen on or off. BLK RW 0: Off, 1: On
Volume:Specifies a value to adjust the volume level. This 
setting is applied to the input source signal that is 
currently being projected by the projector.VOL RW 0-30 
						

							62
Color Mode: Selects the color mode. PST RW 1: Graphics, 2: Theater, 
3: Standard, 4: Blackboard, 
5: Game
Aspect Ratio: Specifies the aspect ratio. ARZ RW 0: Normal*
1, 1: 16:9, 
2: Normal*2, 4: Full
Get Light Time: Gets the light time from the projector. LMP R 0- Unit: Hours
*1 Input source: RGB or HDMI (PC)
*2 Input source: Video, S-video, component or HDMI (DTV)
FunctionCommand 
NameRWSetting Range 
						

							63
*XJ-H1650/XJ-H1750/XJ-ST145/XJ-ST155 only
zCASIO COMPUTER CO., LTD. makes no guarantees concerning the operation or suitability of any 
USB device that you connect to the projector’s USB port.
zSpecifications are subject to change without notice.
Specifications
Model NameXJ-H1600XJ-H1650XJ-H1700XJ-H1750XJ-ST145XJ-ST155
Brightness 
(ANSI Lumens)3500 4000 2500 3000
Projection System DLP
DLP chip Size: 0.7 inch, Number of Pixels: XGA (1024 ×
 768)
Projection Lens 1.2X manual optical zoom, manual focus Manual focus
Light Source Laser and LED
TerminalsCOMPUTER IN:RGB 15-pin mini D-Sub ×
 2 (Also used as component signal input terminal.)
MONITOR OUT: RGB 15-pin mini D-Sub ×
 1
VIDEO: RCA pin jack ×
 1
S-video: 4-pin mini DIN ×
 1
HDMI: HDMI type A terminal ×
 1
AUDIO IN: 3.5 φ
 stereo mini jack ×
 2, RCA pin jack ×
 2
AUDIO OUT: 3.5 φ
 stereo mini jack ×
 1
SERIAL: 9-pin D-Sub ×
 1
USB
*: TYPE A terminal ×
 1, TYPE B terminal ×
 1
LAN*: RJ-45 terminal ×
 1
Display LanguagesEnglish, French, German, Italian, Spanish, Swedish, Portuguese, Turkish, Russian, 
Chinese (Simplified), Chinese (Traditional), Korean, Japanese
D 
						

							MA1108-D