Casio Projector XJ-H1700 XJ-H1750 User Manual

							51
Input source: Video, S-video, component or HDMI (DTV)
Input SignalNormal16:9
4:3 Aspect Image
Squeezed Image
Letter Box Image 
						

							52
Important!Even if a signal is listed in the table below, it does not guarantee that you will be able to display 
its images correctly.
RGB Signal
Supported Signals
Signal NameResolutionHorizontal Frequency 
(kHz)Vertical Frequency 
(Hz)
VESA640 × 480/60 640 × 480 31.5 60
640 × 480/72 640 × 480 37.9 73
640 × 480/75 640 × 480 37.5 75
640 × 480/85 640 × 480 43.3 85
800 × 600/56 800 × 600 35.2 56
800 × 600/60 800 × 600 37.9 60
800 × 600/72 800 × 600 48.1 72
800 × 600/75 800 × 600 46.9 75
800 × 600/85 800 × 600 53.7 85
1024 × 768/60 1024 × 768 48.4 60
1024 × 768/70 1024 × 768 56.5 70
1024 × 768/75 1024 × 768 60.0 75
1024 × 768/85 1024 × 768 68.7 85
1152 × 864/75 1152 × 864 67.5 75
1280 × 768/60 1280 × 768 47.8 60
1280 × 800/60 1280 × 800 49.7 60
1280 × 960/60 1280 × 960 60.0 60
1280 × 960/85 1280 × 960 85.9 85
1280 × 1024/60 1280 × 1024 64.0 60
1280 × 1024/75 1280 × 1024 80.0 75
1280 × 1024/85 1280 × 1024 91.1 85
1360 × 768/60
*11360 × 768 47.7 60
1366 × 768/60
*21366 × 768 47.7 60
1400 × 1050/A
*11400 × 1050 65.3 60
1440 × 900/60 1440 × 900 55.9 60
1600 × 1200/60 1600 × 1200 75.0 60
1680 × 1050/60 1680 × 1050 65.3 60
Other1152 × 864/70 1152 × 864 64.0 70
1400 × 1050/B
*11400 × 1050 64.0 60
*1  If these signals do not project correctly, change the “Option Settings 1J Auto Adjust” setting to “2” 
(page 35).
*2  If this signal does not project correctly, change the “Option Settings 1
J Auto Adjust” setting to “3” 
(page 35). 
						

							53
Component Signal
Video Signal, S-video Signal
Signal NameHorizontal Frequency 
(kHz)Vertical Frequency 
(Hz)
HDTV1080p/50 56.3 50
1080p/60 67.5 60
720p/50 37.5 50
720p/60 45.0 60
1080i/50 28.1 50
1080i/60 33.7 60
SDTV576p/50 31.3 50
576i/50 16.6 50
480p/60 31.5 60
480i/60 15.7 60
Signal NameHorizontal Frequency 
(kHz)Vertical Frequency 
(Hz)
NTSC 15.7 60
NTSC4.43 15.7 60
PAL 15.6 50
PAL-M 15.7 60
PAL-N 15.6 50
PAL60 15.7 60
SECAM 15.6 50 
						

							54
HDMI Signal
3D Signals (3D Input Mode)
Signal NameHorizontal Frequency 
(kHz)Vertical Frequency 
(Hz)
640 × 480/60 31.5 60
800 × 600/60 37.9 60
1024 × 768/60 48.4 60
1280 × 768/60 47.8 60
1280 × 800/60 49.7 60
1280 × 960/60 60 60
1280 × 1024/60 64 60
1400 × 1050/60 65.3 60
SDTV (480p) 31.5 60
SDTV (576p) 31.25 50
HDTV (720p) (50) 37.5 50
HDTV (720p) (60) 45 60
HDTV (1080i) (50) 28.13 50
HDTV (1080i) (60) 33.75 60
HDTV (1080p) (50) 56.25 50
HDTV (1080p) (60) 67.5 60
Signal NameHorizontal Frequency 
(kHz)Vertical Frequency 
(Hz)
RGB Signal640 × 480/60 31.5 60
640 × 480/120 61.7 120
800 × 600/60 37.9 60
800 × 600/120 77.2 120
1024 × 768/60 48.4 60
1024 × 768/120 98.8 120
1280 × 768/60 47.8 60
1280 × 768/120 97.4 120
1280 × 800/60 49.7 60
1280 × 800/120 101.6 120
Video SignalNTSC 15.7 60 
						

							55
The projector can be controlled by a computer or other external device by connecting the device to 
the projector’s LAN port.
Supported External Devices
This projector supports all commands of PJLink Class1 (Version 1.00).
http://pjlink.jbmia.or.jp/english/
This projector is supported by the commands of the Crestron Electronics controller and software 
(RoomView®).
http://www.crestron.com/
This projector is supported by AMX Device Discovery.
http://www.amx.com/
Information about the types of external devices that can be connected to the LAN port and control the 
projector, as well as the control commands supported for each external device will be published on 
the CASIO website below as such information becomes available.
http://www.casio.com/support/
Controlling the Projector from a Computer
When the projector is linked to a computer over a wired or wireless LAN connection, you can use the 
computer’s Web browser to access a Wireless Presentation System control panel to control the 
projector.
To establish a wired LAN connection between the projector and a computer
1.Connect the LAN port of the projector to the LAN hub or other network devices 
to which the computer is connected.
zIn a configuration like the one in the illustration above, you should normally use straight type 
LAN cables. If you are connecting the projector’s LAN port directly to the LAN port of a 
computer, use a cross type LAN cable.
Using Wired LAN to Control the Projector 
(XJ-H1650, XJ-H1750, XJ-ST145, XJ-ST155)
Projector
ComputerLAN hub
D 
						

							56
2.Look up the projector’s IP address.
zPerform the following steps to look up the projector’s current IP address.
3.On the computer, start up a Web browser.
4.In the Web browser address bar, input the projector’s IP address and then press 
the [Enter] key.
zIf the projectors current IP address is 192.168.100.10, for example, you would input: 
“http://192.168.100.10”.
zThis displays the top page of the projector’s System Admin page.
zFor information about what you should do next, see “To control the projector using the 
Wireless Presentation System control panel” (page 57).
Important!Under initial default settings, the projector is configured to obtain its IP address automatically 
from the DHCP server. This means that an IP address will be assigned automatically whenever 
the projector is connected to a DHCP environment network.
Depending on the network environment being connected to, there may be cases where you will 
need to assign a projector’s IP address manually. In such cases, you will need to configure 
projector’s network settings.
If you are unable to display the projector’s System Admin page with your browser using the 
above procedure, it may mean that there is some problem with your network settings. Refer to 
the Wireless Function Guide on the CD-ROM that comes with the projector and establish a 
wireless LAN connection between the projector and your computer. After configuring the 
projector’s network settings, try performing the above procedure again. For details about the 
projector’s network settings, see “To configure projector’s network settings and wireless LAN 
connection settings” in the Wireless Function Guide. 1. Press the [MENU] key to display the setup menu.
2. Use the [T] and [S] keys to select “Wired LAN settings” and then press the [ENTER] key.
3. Use the [T] and [S] keys to select “Wired LAN info” and then press the [ENTER] key. 
						

							57
To control the projector using the Wireless Presentation System control 
panel
1.Depending on the type of LAN connection you are using, perform either of the 
following operations to display the top page of the projector’s System Admin 
page.
2.Click “System Admin”. On the password input screen that appears, enter the 
password.
zThe initial default password is “admin”.
3.Click the [Login] button.
zThis logs in to the System Admin page and displays the Status screen.
4.Click “Control Panel” on the left side of the screen.
zThis will display a control panel screen like the one shown below.
zThe table below explains the status information and the projector operations included on the 
control panel screen. Wired LAN Connection:
“To establish a wired LAN connection between the projector and a 
computer” (page 55)
Wireless LAN Connection: Steps 1 and 2 under “To log in to the projector’s System Admin 
page” of the Wireless Function Guide on the CD-ROM that comes 
with the projector
GroupItemDescription
Refresh (Button) Click to refresh the screen with the latest information.
Status Projector status Shows the projector’s current status as either “On” or “Standby”.
Error info Shows one of the following.
Normal: Operating normally.
Temperature error: Temperature error occurred.
Fan error: Fan error occurred.
Light error: Light source unit error occurred.
Other error: Error other than above occurred.
Power On/Power Off 
(Buttons)Turn the projector on/off.
[Power On] button operation is supported only when the projector is 
connected to a computer of a wired LAN connection, and “Enable” is 
selected for the “Remote on” setting (pages 38).
D 
						

							58
Image Input Specifies the input source. The following are the available input source 
options.
3D Puts the projector into the 3D input mode or normal input mode.
On: 3D input mode
Off: Normal input mode
zNote that this setting cannot be change while the currently selected 
input source is “Computer 1 (Component)”, “Computer 2 
(Component)”, “HDMI”, or “USB”.
Color mode Specifies the color mode.
zFor details about this setting, see “Selecting the Color Mode” (page 
14).
Blank Selecting “On” for this setting temporarily blocks the image from the 
input source. “Off” causes the image from the input source to be 
projected.
zThe operation of this item is identical to that of the remote controller’s 
[BLANK] key. For details, see “Momentarily Cutting Off the Input 
Source Image” (page 15).
Aspect ratio Changes the aspect ratio of the projected image.
zFor details about this setting, see “Changing the aspect ratio of the 
projected image” (page 17).
Brightness This corresponds to the “Image Adjustment 1 J Brightness” setting of 
the setup menu. Input a value into the box and then click the [Apply] 
button. This will change the projector’s “Brightness” setting accordingly.
Contrast This corresponds to the “Image Adjustment 1 J Contrast” setting of the 
setup menu. Input a value into the box and then click the [Apply] button. 
This will change the projector’s “Contrast” setting accordingly.
Eco Mode Switches the Eco mode.
zFor details about this setting, see “Eco Mode (Power Saving, Low 
Noise)” (page 19).
Audio Volume Input a value into the box and then click the [Apply] button. This will 
change the volume setting accordingly.
Mute Specifies the mute setting. Audio is output while “Off” is selected for this 
setting, and muted when “On” is selected.
Audio Output Specifies either output from the projector’s speaker output or AUDIO 
OUT terminal for audio.
Speaker: Audio output from the speaker
Line: Audio output from the AUDIO OUT terminal
Factory Defaults (Button) Clicking to return all control panel items, except for the “Projector status” 
item, to their initial factory defaults.
GroupItemDescription
3D Off3D On
Computer 1/2 (Auto) Computer 1/2 (RGB)
Computer 1/2 (RGB) Video
Computer 1/2 (Component) S-video
Video
S-video
HDMI
USB 
						

							59
5.After all of the settings are the way you want, click “Logout”.
NoteThe “Status”, “Setup”, “Change Password”, and “Restore Factory Defaults” items along the left 
side of the screen are mainly for accessing information and configuring settings related to 
projector wireless LAN connection. You can access these items when connected over a wired 
LAN as well. For details, see “System Admin Page Operations and Settings” in the “Wireless 
Function Guide” on the CD-ROM that comes with the projector. 
						

							60
You can use a commercially available serial cable (cross) to connect the projector to a computer and 
control the projector from the computer.
Connecting the Projector to a Computer
Connect the projector to the computer as shown in the illustration below.
*A D-Sub 9-pin (male) type connector is standard for computer serial ports, but there may be cases 
where the shape of a particular computer’s connector is different. For details about connecting a 
commercially available serial cable to your computer, see the user documentation that comes with 
it.
Using Control Commands
This section explains the commands that are used to control the projector from a computer.
Command Send Format
Projector RS-232C Control
Communication 
ProtocolConfigure your computer’s serial port with the following settings.
Data Rate 19200bps
Data Bit 8bit
Parity None
Stop Bit 1bit
Flow Control None
Read CommandSend this command when you want information about the current setup of the data 
projector.
Send Format (?)
Receive Format (,)
Command Send 
Example sent from the computer to the projector.
4
 returned from the projector to the computer.
Write CommandSend this command to control the data projector (power on/off, etc.) and to write data to it.
Send Format ()
Command Send 
Example sent from the computer to the projector.
4
Projector volume setting becomes 0 (mute).
Projector
Commercially available serial cable (cross)Computer
Serial por t (RS-232C)
D-Sub 9-pin (female)
Serial port* D-Sub 9-pin (female)
(
VO L ?)
(
0-
30,15)
(
VO L 0)