Casio Qt 6100 Service Manual

— 19 —
■ QT-6060D
  1. Assemble the LCD Unit in the FRONT CASE with seven screws.
  2. Connect the connector and fix the HINGE with five screws.
Screw × 7
Screw × 5
  3. After fixing the packing to the REAR CASE, assemble the REAR CASE and the FRONT CASE.
Hooks
  4. Remove the LCD unit with four screws.
   Position: under both packing
Screw × 2Screw × 2 

— 20 —
  5. Fix the cap to the LCD Unit.
   Be careful with the position of the screw holes.
  6. Fix the cap to the stand.
   Be careful with the direction of the cap. The height of the screw hole on the front side should be lower.
Screw × 4
  7. Let the connector through the cap and fix the LCD unit with four screws.
  8. Connect the connector and fix the IO Unit with four screws.
Screw × 4Connector 

— 21 —
5. OPTION INSTALLATION
5-1. To install the I-Button
  3.  Insert the I-Button.  Fix it with a nut.  Insert the earth plate.  Fix it with a nut.
  4.  Assemble the lead wire (earth) into the connector.
  5.  Wind the lead wire around the core twice, and then connect the core to the connector of the main unit.
  1.  Remove the REAR COVER for QT-6100 (No.1 to No.10 in the disassembly procedure).
  2.  Remove one screw and then the I-Button cover. 

— 22 —
  6.  Store the core in the main unit, and then fix it with fabric tape.
5-2. To install the MCR
  1.  Remove the REAR COVER for QT-6100 (No.1 to No.10 in the disassembly procedure).
  2.  Remove the packing from the main unit.
  3.  Insert the MCR into the special metal bracket.
    NOTE: Be careful not to damage the FPC.
FPC 

— 23 —
  4.  Connect the connector and fix the metal bracket with two screws.
    NOTE: The lead wires should be stored neatly in a line.
  5.  Fix the metal bracket to QT-6100 with two screws.
  6.  Connect the connector to QT-6100.
    NOTE: Arrange the cables so that they do not tangle with each other. 

— 24 —
5-4. To install the DRAWER
 In case of connecting drawer, follow the procedure below.
  1.  Connect drawer connector (three color lead on drawer) to the terminal.
  2.  Connect frame drawer connector (green lead on drawer) to the terminal.
Mount the cash register.
  1.  Screw in 2 fixing screws bottom side of the terminal.
  2.  Mount the terminal on the top of the drawer, ensuring that the feet on the bottom of the terminal go into the 
holes on the drawer.
5-3. REMOTE PRINTER / SLIP PRINTER...

— 25 —
Max.100m
Maximum 32 terminals Max.300m
Max.100m
Max.100mMax.100m
Maximum 32 terminals Max.500m
Max.100m
Max.100m
Max.100m
Max.100m
6. IN LINE / OUT LINE
   With the QT-6100, there are the following inline / online connectors in the rear side of the body.
6-1. Inline interface
   The maximum inline cable length and the maximum connection unit will be varied by the inline communica-
tion speed as shown below figure.
  • Using 10BASE-T
   Cable length: 100m (terminal to terminal, hub to terminal, hub...

— 26 —
6-2. Online interface
   Only the RS-232C Com1 port can be connected with a modem or perssonal computer.
   Direct connection to PC
    Connection layout
Note:  Maximum  3  remote  printers  in  the  1 
terminal system, 6 remote printers / 2 
terminal  system,  8  remote  printers  in 
the 3 ~ 32 terminal can be defined.
PC
Via COM 1 port of the master terminal
or Inline (Ethernet)
Maximum 32 terminals
   MODEM system
    Connection layout
Note:  Maximum  3  remote  printers  in 
the 1 terminal...

— 27 —
INIT
Copyright(C)2004                     
CASIO COMPUTER CO.,LTD.
C
All rights reserved.
ROM VER xxxxxx xxxx
7 8 9
CREATE xxxx-xx-xx xx:xx
QT-6100  Versionx.xx 4 5 6
APL VER. xxxxxx xxxx
1 2 3
0
OK
Init Sw
7. DIAGNOSTIC OPERATION 
7-1. To start the diagnostic program
(1)  Turn the power off.
(2)  Turn the power on while pressing the INIT switch.
(3)  Release the switch when the display shown below appears.  
      * Operation is not guaranteed if the switch is released before the display...

— 28 —
Device Status Information (Displayed Information)
Dallas key Dallas key no.
Dallas key 2 Dallas key no. 
Drawer Open/close status     
MAC address MAC address     
CF Insertion status 
DISP ON/OFF switch  Switch status
TEMP Power supply A/D conversion value
 * Display only updated when DISP ON/OFF switch is ON 
7-3. DIAG command input system
   Input a command according to the following code. 
XXXXXXnagd
XXXXXX : additional action
n : number of times
a : action
g : group
d : device number
7-4....