Casio Xj 360 Dlp Users Guide

11
Projection Operations
The color mode setting lets you specify the type of image you will be projecting, so the 
projector can optimize image color.
To change the color mode setting
1.Press the [COLOR MODE] key.
zThis causes the color mode screen to appear on the projection image. The z mark 
indicates the current color mode setting.
zFor details about each of the settings, see “Image Adjustment J Color Mode” on 
page 28.
2.Use the [S] and [T] keys to move the cursor to the setting you want, 
and then...

Projection Operations
12
You can use the remote controller keys to adjust the volume level of the audio that is output 
from the projector’s speaker.
To adjust the volume level
1.On the remote controller, press the [VOL +] or [VOL –] key.
zThis causes the [Volume] screen to appear on the projected image.
2.Press the [VOL +] key or the [X] key to increase the volume, or the 
[VOL –] or [W] key to lower the volume.
3.To close the setup screen, move the cursor to “Close”, and then press 
the [ENTER] key....

13
Projection Operations
You can use the remote controller’s zoom keys to enlarge a specific part of the projected 
image.
To enlarge part of the projected image
1.On the remote controller, press the [D-ZOOM +] or [D-ZOOM –] key.
zThis causes a cross cursor ( ) to appear on the projected image.
2.Use the remote controller’s cursor keys to move the cross cursor to the 
part of the image that you want in the center of the enlarged image.
3.On the remote controller, press the [D-ZOOM +] key to enlarge the...

Projection Operations
14
The freeze function stores the current projected image in projector memory, and projects it as 
a still image.
To freeze the projected image
1.On the remote controller, press the [FREEZE] key.
zThis freezes the image that was being projected when you pressed the [FREEZE] key.
2.To unfreeze the image, press the [FREEZE] key again or press the 
[ESC] key.
Use the procedures in this section to display the pointer and to select its shape (arrow, bar). 
You can use the pointer to...

15
Projection Operations
Selecting the Pointer Shape
Each press of the [POINTER/SELECT] key while the pointer is displayed cycles through the 
pointer shapes in the sequence shown below.
To clear the pointer from the image
Press the [ESC] key.
Downloaded From projector-manual.com Casio Manuals 

Using the Setup Menu
16
Using  the  Setup Menu
Pressing the [MENU] key while an image is being projected displays the setup menu on the 
projected image. The setup menu can be used to configure a variety of different projector 
settings. The following table shows the menu items that are available in the Setup Menu.
Setup Menu Overview
Main menu Sub-menu Sub-menu Item Type ∗1Input source ∗2
See page
RCS V–
Image 
Adjustment Brightness Value Setting 27
Contrast Value Setting 27
Sharpness Value Setting 27...

17
Using the Setup Menu
Main menu Sub-menu Sub-menu Item TypeInput source
See page
RCS V–
Detailed 
SettingsVo l u m e Va l u e  S e t t i n g*535
Pointer Selection 36
Low-noise Mode Selection∗
11∗11∗11∗11∗1136
Power On Password Special∗10 37
Change Password Special∗10 37
Advanced Settings 1
Auto Input Detect Selection 40
Auto Keystone 
CorrectionSelection 40
Auto Adjust Selection∗641
Show Screen Text Selection 41
Startup Screen Selection 42
No Signal Screen Selection 42
Advanced Settings 2
Auto Power...

Using the Setup Menu
18
Before Configuring Menu Settings
Always remember that the settings you configure on the setup menu are applied for the input 
source (RGB, Component, S-VIDEO, VIDEO) that was selected when you displayed the setup 
menu. Note the following important points.
zThe items that appear on the setup menu depend on the currently selected input source 
and other factors.
Some items apply to a certain specific input source, while some apply to multiple input 
sources.
zEven for menu items...

19
Using the Setup Menu
This section explains projector operations you need to perform while configuring setup menu 
settings. It also provides details about each sub-menu item type.
Basic Setup Menu Operations
The following is the general flow of the steps you need to perform when configuring setup 
menu operations.
1.Select the input source whose settings you want to configure.
2.Press the [MENU] key.
zThis causes the setup menu screen to appear in the upper left corner of the projected 
image. At this...

Using the Setup Menu
20
4.Use the [S] and [T] keys to move the highlighting to the main menu 
item you want.
z The sub-menu for the currently selected main menu item will appear to the right.
5.Press the [X] key or the [ENTER] key.
zThis will cause the item at the top of the currently displayed sub-menu to become 
highlighted, indicating that it is selected.
6.Select the sub-menu item whose setting you want to change.
zUse the [S] and [T] keys to move the highlighting to the sub-menu item you want....