Cisco D9854i Manual

 
 
Fault History ............................................................................................................ 315 
Log History .............................................................................................................. 316 
Appendix D Compliance 317 
Applicable Standards and Notices .................................................................................... 318 
Safety...

 
  About This Manual  
78-4021470-01 Rev J xxiii 
 
About This Manual 
Objective 
This manual describes how to install, use and maintain the Cisco® D9854 Advanced 
Program Receiver. 
Note: The manual describes all available options for the D9854 receiver. Your D9854 
receiver may only have some of the features described in this manual.   
Audience 
The audience of this manual includes users (operators) and service personnel who 
are responsible for the installation, configuration, operation, monitoring...

 
 
78-4021470-01 Rev J 1 
 
Overview 
This chapter provides a quick setup for your D9854 receiver. If you are 
unsure about which receiver settings to use, contact your local service 
provider for assistance.  
 
 
1 Chapter 1 
Quick Setup - Read Me First! 
In This Chapter 
 Connecting the Receiver to Other Equipment .................................... 2 
 Setting up for Network Connection ..................................................... 4 
 Quick Setup Instructions for RF Acquisition...

 
Chapter 1    Quick Setup - Read Me First!  
 
 
2 78-4021470-01 Rev J 
Connecting the Receiver to Other Equipment 
The following displays the rear panel of the D9854 Base Model: 
 
The following displays the rear panel of the D9854 SDI Model, with SD/HD-SDI and 
AES outputs: 
 
1 Connect the L-Band signal to RF1. 13V or 18V LNB power is only available on 
the RF1 port. The factory default setting for LNB power is OFF.  
2 Connect the ASI OUT port to an ASI device for digital tier applications. 
3...

 
 
 Connecting the Receiver to Other Equipment 
 
78-4021470-01 Rev J 3 
 
Maintenance of EMC Compliance 
The power cord (consisting of appliance coupler, flexible cord, and plug) supplied 
with this product meets the requirements for use in the country for which this 
product was purchased. In general, the power cord must be approved by an 
acceptable, accredited agency responsible for evaluation in the country where the 
product will be used.  
Double-shielded (braid/foil or braid/braid) cables should...

 
Chapter 1    Quick Setup - Read Me First!  
 
 
4 78-4021470-01 Rev J 
Setting up for Network Connection 
1 Press MENU to display the Main menu.  
2 Press  to go to the Setup menu. Press SELECT. Press  twice to select the IP 
menu. Press SELECT twice to go to the IP menu. 
3 Use the  arrow keys to navigate up and down the IP menu, and the   arrow 
keys to move across the IP menu to set the IP Address, Mask and Gateway 
parameters. Use the number keys to directly enter numbers in the fields. For 
more...

 
 
 Quick Setup Instructions for RF Acquisition 
 
78-4021470-01 Rev J 5 
 
Quick Setup Instructions for RF Acquisition 
1 Press MENU to display the Main menu.  
2 Press  to go to the Setup menu. Press SELECT. Press to move to the TS Input 
menu. Press SELECT.   
3 To setup the ASI input port, go to step 4. To setup the RF1 input port, go to step 
5. 
4 Press SELECT three times. Press  to set the ASI port to Act (Activate). Press 
SELECT. Go to step 11. 
5 Press SELECT. Press to go to RF1. Press...

 
Chapter 1    Quick Setup - Read Me First!  
 
 
6 78-4021470-01 Rev J 
13 If the front LED is solid green, the unit is authorized. Proceed with Assigning a 
Program Channel to a PE (Program Entry). If the front LED is flashing green, the 
unit is unauthorized. Please contact your service provider and provide the 
Tracking ID number for authorization. The Tracking ID can be found on the 
ABOUT menu. To locate the Tracking ID, press MENU, press twice, and then 
press SELECT twice. Make a note of the...