Cisco Systems Active Voice Repartee Unity R2 4 Installation Guide

							APPPENDIX A: Voice and fax boards123
Software settings
During Unity Setup, do the following procedure when the Dia-
logic D/SC Configuration dialog box appears.
To enter Dialogic settings during Unity Setup
aChange the value of “BLTInterrupt” to “5.”
bChange the value of “BLTAddress” to the appropriate value:
Turnkey systemSelect “D0000.”
Component systemSelect the address that you reserved 
during the procedure “To find and reserve memory 
addresses and an IRQ (ISA boards in a component system 
only),” on page 35.
cClick “OK” to continue.
dReturn to the procedure that you were doing when the Dia-
logic D/SC Configuration dialog box appeared. 
						

							UNITY INSTALLATION GUIDE124
Dialogic 
D/41ESC-Euro 
voice board
0

Voice board backplate
SC bus connector Switch SW1 Switch block SW2
To p  v i e w
Side view
Pin 4: Unused
Connection pinouts
The D/41ESC-Euro uses 
RJ-11 connectors.
Line 1
Line 2
Line 3
Line 4
Pin 1: Unused
Pin 2: Tip
Pin 3: Ring 
						

							APPPENDIX A: Voice and fax boards125
Hardware settings
Do the following procedures as you install voice boards.
To  s e t  t h e  S W 1  s w i t c h
For each Dialogic ISA voice board that has a rotary switch, 
set the rotary switch to a unique value starting with 0 and 
continuing in sequence.
For example, set the rotary switch on the first three ISA 
voice boards in the Unity server as shown below. This is also 
the order in which you install the boards in the server.
To  s e t  s w i t c h  b l o c k  S W 2
Set SW2 switches to “Off” on all boards.
Software settings
During Unity Setup, do the following procedures when the Dia-
logic D/SC Configuration dialog box appears.
To enter Dialogic settings during Unity Setup
aChange the value of “BLTInterrupt” to “5.”
bChange the value of “BLTAddress” to the appropriate value:
Turnkey systemSelect “D0000.”
Component systemSelect the address that you reserved 
during the procedure “To find and reserve memory 
addresses and an IRQ (ISA boards in a component system 
only),” on page 35.
cDo not click “OK” to continue. Instead, continue with the 
next procedure.
Continued First ISA board
Second ISA board
Third ISA board
0
1
2 
						

							UNITY INSTALLATION GUIDE126
Dialogic 
D/41ESC-Euro 
Continued
voice board
To set the parameter file for the D/41ESC-Euro board
aOn the Windows Start menu, click Programs > Dialogic Sys-
tem Software > Dialogic Configuration Manager–DCM.
The tree-structured list contains an entry for each Dialogic 
board installed in the server. Note that the D/41ESC-Euro 
board is displayed in the list as “D/41ESC.”
bDouble-click the first occurrence of “D/41ESC” in the tree 
list. The Properties dialog box for the board appears.
cClick the Country tab.
dChange the value of “Country” to “Euro (CTR-21).”
eClick “OK.”
fTo set additional D/41ESC-Euro boards, double-click the 
next occurrence of “D/41ESC” in the list and repeat steps 
cthroughe.
gClose the DCM.
hIn the Dialogic D/SC Configuration dialog box, click “OK” to 
continue with Unity setup.
iReturn to the procedure that you were doing when the Dia-
logic D/SC Configuration dialog box appeared. 
						

							APPPENDIX A: Voice and fax boards127
Dialogic 
D/120JCT-LS 
voice board
Continued
Vo i c e  b oa r d  b a c k p l a t e Connection pinouts
The D/120JCT-LS uses 
RJ-25 connectors.
Lines 1 and 2
Lines 3 and 4
Lines 5 and 6
Lines 7 and 8
Pin 6: Ear th recall 2
Pin 5: Ring 2
Pin 4: Tip 1
Pin 3: Ring 1
Pin 2: Tip 2
Pin 1: Ear th recall 1Switch SW100 Switch SW1
Side view To p  v i e w
Lines 9 and 10
Lines 11 and 12 CT bus connector 
						

							UNITY INSTALLATION GUIDE128
Dialogic 
D/120JCT-LS voice 
Continued
boardHardware settingsDo the following procedures as you install voice boards.
To set the SW100 switch
For each Dialogic PCI voice board that has a rotary switch, 
set the rotary switch to a unique value starting with 1 and 
continuing in sequence. 
For example, set the rotary switch on the first three PCI 
voice boards in the Unity server as shown below. This is also 
the order in which you install the boards in the server. 
To  s e t  t h e  S W 1  s w i t c h
Set switch SW1 to “On hook” on all boards as shown below.
Software settings
None.
First PCI board
Second PCI board
Third PCI board1
2
3
On hook 
						

							APPPENDIX A: Voice and fax boards129
Dialogic 
D/160SC 
voice board
Continued
SC bus connector
Side view To p  v i e w
Switch SW 100 
						

							UNITY INSTALLATION GUIDE130
Dialogic D/160SC 
Continued
voice board
Use the Dialogic D/160SC voice board with the VTG VoiceBridge 
2000 feature-set board to provide feature-set integration on 
Mitel SX-200 and SX-2000 phone systems.
All of the D/160SC and VoiceBridge 2000 boards that you are 
installing must be in the same box because they all must be con-
nected with an SC bus cable. If there are not enough slots in the 
Unity server, then you must put all of the boards into an expan-
sion chassis.
Hardware settings
Do the following procedures as you install voice boards.
The IRQ for Dialogic D/160SC boards is 2 on all Unity turnkey 
systems except the Dell 2400. On the Dell 2400, the IRQ for 
D/160SC boards is 5.
To set the SW100 switch
For each Dialogic ISA voice board that has a rotary switch, 
set the rotary switch to a unique value starting with 0 and 
continuing in sequence. 
For example, set the rotary switch on the first three ISA 
voice boards in the Unity server as shown below. This is also 
the order in which you install the boards in the server. 
First ISA board
Second ISA board
Third ISA board0
1
2 
						

							APPPENDIX A: Voice and fax boards131
Software settings
During Unity Setup, the Dialogic D/SC Configuration dialog box 
appears. Do the following procedure after you have done the pro-
cedure “To enter VoiceBridge 2000 settings during Unity Setup,” 
on page 161.
To enter Dialogic settings during Unity Setup
aChange the value of “BLTInterrupt” to the appropriate value:
All turnkey systems, except Dell 2400Select “2.”
Dell 2400 turnkey systemSelect “5.”
Component systemSelect the IRQ that you reserved dur-
ing the procedure “To find and reserve memory addresses 
and an IRQ (ISA boards in a component system only),” on 
page 35.
bChange the value of “BLTAddress” to the appropriate value:
Turnkey systemSelect “D0000.”
Component systemSelect the address that you reserved 
during the procedure “To find and reserve memory 
addresses and an IRQ (ISA boards in a component system 
only),” on page 35.
cClick “OK” to continue.
dReturn to the procedure that you were doing when the Dia-
logic D/SC Configuration dialog box appeared. 
						

							UNITY INSTALLATION GUIDE132
Dialogic 
D/160SC-LS 
voice boardSC bus
connectorSwitch
SW100Switch 
SW600
DB-37 connector
To p  v i e w
Side view
Connection pinouts
The D/160SC-LS uses a DB-37 
connector. See the table on the 
next page for pinout information.
Pin 1
Pin 20