compaq evo notebook n1000 series User Manual

							Removal and Replacement Procedures
Maintenance and Service Guide5–9
6. Remove the hard drive by following these steps:
a. Turn the computer bottom side up with the right side 
facing forward.
b. Remove the TM2.5 ×8.0 hard drive retention screw 
1 
(Figure 5-6).
c. Slide the hard drive forward 
2 to unseat the hard drive 
connector from the system board.
Figure 5-6. Removing the Hard Drive Screw
Hard Drives
Spare Part Number Information
60 GB
40 GB
30 GB
20 GB303527-001
273491-001
192406-001
288291-001
279372-001.book  Page 9  Friday, July 19, 2002  11:50 AM 
						

							5–10Maintenance and Service Guide
Removal and Replacement Procedures
d. Lift the front edge of the hard drive 1 until it rests at an 
angle (Figure 5-7).
e. Remove the hard drive from the hard drive bay 
2.
Figure 5-7. Removing the Hard Drive
279372-001.book  Page 10  Friday, July 19, 2002  11:50 AM 
						

							Removal and Replacement Procedures
Maintenance and Service Guide5–11
7. Remove the four PM3.0 × 3.0 screws 1 that secure the hard 
drive to the hard drive bracket (Figure 5-8).
8. Slide the hard drive out of the hard drive bracket 
2.
Figure 5-8. Removing the Hard Drive Bracket
✎Hard drive brackets are available with carbon finish for 
Evo Notebook N1000 models and silver finish for Presario 1500 
models, and are included in the Miscellaneous Plastics/Hardware 
Kit, spare part number 285541-001.
Reverse the preceding procedures to install the hard drive and 
hard drive bracket.
279372-001.book  Page 11  Friday, July 19, 2002  11:50 AM 
						

							5–12Maintenance and Service Guide
Removal and Replacement Procedures
5.4 Computer Feet
The computer feet are adhesive-backed rubber pads. The 
computer feet are included in the Miscellaneous 
Plastics/Hardware Kit, spare part number 285541-001. The 
computer feet attach to the base enclosure as illustrated in 
Figure 5-9.
Figure 5-9. Replacing the Computer Feet
5.5 Memory Expansion Board
1. Prepare the computer for disassembly (Section 5.3).
2. Turn the computer bottom side up with the front facing 
forward.
Memory Expansion Boards
Spare Part Number Information
512 MB
256 MB
128 MB285524-001
285523-001
285222-001
279372-001.book  Page 12  Friday, July 19, 2002  11:50 AM 
						

							Removal and Replacement Procedures
Maintenance and Service Guide5–13
3. Remove the PM2.5 × 4.0 screw 1 that secures the memory 
expansion compartment cover to the base enclosure 
(Figure 5-10).
4. Slide the cover to the right 
2.
5. Lift the right edge of the cover and swing it to the left 
3.
6. Remove the cover.
Figure 5-10. Removing the Memory Expansion 
Compartment Cover
✎Memory expansion compartment covers are available with carbon 
finish for Evo Notebook N1000 models and silver finish for 
Presario 1500 models, and are included in the Miscellaneous 
Plastics/Hardware Kit, spare part number 285541-001.
279372-001.book  Page 13  Friday, July 19, 2002  11:50 AM 
						

							5–14Maintenance and Service Guide
Removal and Replacement Procedures
7. Spread the memory expansion slot retaining tabs 1 to release 
the memory expansion board. The board tilts up at a 
45-degree angle (Figure 5-11).
8. Remove the board by pulling it away from the connector at a 
45-degree angle 
2.
Figure 5-11. Removing a Memory Expansion Board
Reverse the preceding procedures to install a memory 
expansion board.
5.6 Mini PCI Communications Board
Mini PCI Communication Boards
Spare Part Number Information
U.S. modem
International modem248776-001
285545-001
279372-001.book  Page 14  Friday, July 19, 2002  11:50 AM 
						

							Removal and Replacement Procedures
Maintenance and Service Guide5–15
1. Prepare the computer for disassembly (Section 5.3).
2. Turn the computer bottom side up with the rear panel facing 
forward.
3. Remove the PM2.5 × 4.0 screw 
1 that secures the mini PCI 
compartment cover to the base enclosure (Figure 5-12).
4. Slide the cover to the left 
2.
5. Lift the left edge of the cover and swing it to the right 
3.
6. Remove the cover.
Figure 5-12. Removing the Mini PCI Communications 
Slot Cover
✎Mini PCI compartment covers are available with carbon finish for 
Evo Notebook N1000 models and silver finish for Presario 1500 
models, and are included in the Miscellaneous Plastics/Hardware 
Kit, spare part number 285541-001.
279372-001.book  Page 15  Friday, July 19, 2002  11:50 AM 
						

							5–16Maintenance and Service Guide
Removal and Replacement Procedures
7. Disconnect the modem cable from the mini PCI 
communications board 
1 (Figure 5-13).
8. Spread the retaining tabs 
2 on each side of the mini PCI 
communications board. The board releases and rests at an 
angle.
9. Remove the board by pulling it away from the socket at an 
angle 
3.
Figure 5-13. Removing a Mini PCI Communications Board
Reverse the preceding procedures to install a mini PCI 
communications board.
279372-001.book  Page 16  Friday, July 19, 2002  11:50 AM 
						

							Removal and Replacement Procedures
Maintenance and Service Guide5–17
5.7 Disk Cell RTC Battery
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the mini PCI compartment cover (Section 5.6).
3. Remove the RTC battery from its socket on the system board 
(Figure 5-14).
Figure 5-14. Removing the Disk Cell RTC Battery
✎The computer uses a CR1220 lithium disk cell battery. When 
replacing the RTC battery, insert the battery with the “+” sign 
facing up.
Disk Cell RTC Battery
Spare Part Number Information
Disk cell RTC battery 279769-001
279372-001.book  Page 17  Friday, July 19, 2002  11:50 AM 
						

							5–18Maintenance and Service Guide
Removal and Replacement Procedures
5.8 Connector Cover
✎The connector cover is available with carbon finish for Evo 
Notebook N1000 models and silver finish for Presario 1500 
models, and are included in the Miscellaneous Plastics/Hardware 
Kit, spare part number 285541-001.
1. Prepare the computer for disassembly (Section 5.3).
2. Turn the computer bottom side up with the rear panel facing 
forward.
3. Remove the two TM2.5 × 5.0 screws 
1 that secure the 
connector cover to the base enclosure (Figure 5-15).
4. Open the connector cover 
2.
5. Remove the connector cover from the base enclosure 
3.
Figure 5-15. Removing the Connector Cover
Reverse the preceding procedures to install the connector cover.
279372-001.book  Page 18  Friday, July 19, 2002  11:50 AM