Daewoo Dt 42a1 Users Manual

							42
PC and DVI Input Resolution Available in PDPPC and DVI Input Resolution Available in PDP
•  Depending on graphic card, problems like no signal detected or line noises can happen. If these problems happen, contact the 
graphic card company for help.
Resolution H Freq. (KHz) V Freq. (Hz)Remark DVI PC
640x400 37.861 85.080 VESA O
640x480 31.469 59.940 DOS O O
37.861 72.809 VESA O O
37.500 75.000 VESA O O
43.269 85.061 VESA O O
720x400 31.469 70.087 IBM O O
37.927 85.039 VESA O
800x600 35.156 56.250 VESA O O
37.879 60.317 VESA O O
48.077 72.188 VESA O O
46.875 75.000 VESA O O
53.674 85.061 VESA O O
1024x768 48.363 60.004 VESA O O
56.476 70.069 HP & VESA O O
60.023 75.029 VESA O O
68.677 84.997 VESA O
 
						

							44
Selecting Picture ModeSelecting Picture Mode
Selecting Picture Mode
•  Press the [PICTURE MODE] on the
remote control.
•  While pressing the [PICTURE MODE] for
the first time, the current picture mode will 
be displayed.
1
Each Press of the Button Will Select 
One of Four Picture Modes.
•  Each time you press the button, a
different picture mode appears. 
The sequence used is as follows:2
•  Select the Picture mode
that is appropriate
depending on the kinds
of pictures, you enjoy.
Selecting 
Picture Mode
Normal /³ Dynamic /³ Cinema /³ User
* Normal :    For a highly defined image in a normally bright
room
* Dynamic:    For a clear-cut image emphasizing high contrast
for sports viewing
* Cinema:  For a movie
* User:  Allows the user to customise settings as desired.
Menu on the Screen will disappear.
•  After selecting a desired picture mode, the
menu on the screen will disappear.
•  If you want to customise the picture modes,
refer to the following page.
3
NOTES:
1) Normal, Dynamic, and Cinema modes are factory preset values.
2)  When adjusting sub-menus while you are in Normal, Dynamic,
and Cinema modes, the Picture Mode will be automatically
converted to User Mode, and the adjustments will be made.
3)  Selecting [Initialise] in the [Features], menu will allow the
Brightness, Contrast, etc. to return to the factory preset values.
 
						

							PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
45
Customising PictureCustomising Picture
•  You can adjust the colour 
tone and brightness to your
preference.
Customising
Picture
Press the MENU Button.
• The MENU shown below will display on the screen.
1
Press the ▼PR▲ Button.
•  After selecting [Picture] by the “PR”, but-
tons, press the  “VOL
” button. Then the sub 
menu of [Picture] will be displayed.2
Select the User Mode.
•  Select [User] by the ”VOL” buttons in the 
[Mode].
3
Picture
Sound
Screen
Feature
InstallMode Normal 
Brightness  32
Contrast  48
Sharpness  32
Color  32
Colour Temp.  Normal
N.R. On
CTI On
Move SelectExit
Picture
Sound
Screen
Feature
InstallMode Normal 
Brightness  32
Contrast  48
Sharpness  32
Color  32
Colour Temp.  Normal
N.R. On
CTI On
Move AdjustExit
Picture
Sound
Screen
Feature
InstallMode User 
Brightness  32
Contrast  48
Sharpness  32
Color  32
Colour Temp.  Normal
N.R. On
CTI On
Move AdjustExit
 
						

							PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
46
Select User Mode Adjustments
•  While you are in [Picture Mode – User], press the “PR” buttons 
to select a specific adjustment item.
4
Picture Condition Adjustments
• Press the “VOL” buttons to adjust the picture of your preference.
•  N.R. and CTI function adjust the noise reduction and color
resolution level of picture respectively.
5
Picture
Sound
Screen
Feature
InstallMode User 
Brightness  32
Contrast  48
Sharpness  32
Color  32
Colour Temp.  Normal
N.R. On
CTI On
Move AdjustExit
NOTES:
1)  While you are in the PC or DVI input mode, you can only adjust 
brightness, contrast and colour temperature.
2)  When you adjust Brightness, Contrast, and Colour in DTV
mode or adjust Brightness and Contrast in PC and DVI mode,
the picture is adjusted finely.
3)  The Tint control is used when the input signal is NTSC or
Component. If input signal is NTSC, Tint control is displayed in
picture menu.
4)  Selecting the colour temperature makes the mood : normal,
warm or cold.
Picture
Sound
Screen
Feature
InstallMode User 
Brightness  32
Contrast  48
Sharpness  32
Color  32
Colour Temp.  Normal
N.R. On
CTI On
Move AdjustExit
 
						

							14:9
LB(14:9)
LBS(14:9)
LB(16:9)
Auto16:94:3
Panorama
LBS(16:9)
• N.B. :  You cannot select screen size if the picture in
picture mode is on.
47
Adjusting ScreenAdjusting Screen
•  You can adjust screen size 
or aspect ratio as desired.
Adjusting with
Screen Size button
Press the SCREEN SIZE Button.
•  The current screen size will be displayed on 
the screen.
•  Each time you press the SCREEN SIZE button 
on the remote control, a different screen size 
appears. The sequence used is as follows in 
case of AV and TV modes :
1
NOTES:
1)  Displaying a picture in a 4:3 mode for a long time may cause
phosphor of the PDP to be burned. So avoid displaying a
picture in 4:3 screen size for a long time.
2)  Under Component,PC and DVI inputs,only 16:9,4:3 and
panorama are available.
3)   Auto : Displays pictures of original picture size.
16:9 : 16:9 picture formats
14:9 : 14:9 picture formats
4:3 : 4:3 picture formats like an analog TV
Panorama : 16:9 picture formats with panorama effect
LB : Enlarges the screen as to fill the black part
above and below the picture.
LBS : Enlarges the screen, and shifts up as to see
the subtitles in case you are watching video
with subtitles.
 
						

							48
 Adjusting Screen in the MENU  Adjusting Screen in the MENU
•  You can adjust the screen in 
the menu.
Adjusting Screen
Press the MENU Button.
• The MENU screen as shown below will appear.
1
Press the “ ▼PR▲ ” Button.
• Press the ”PR” buttons to select ‘Screen’.
2
Picture
Sound
Screen
Feature
InstallMode 16 : 9 
H. Position.    32
V. Posi ti o n    32
Auto  
  
  
Move SelectExit
< In case of PC input >
Picture
Sound
Screen
Feature
InstallMode Normal 
Brightness  32
Contrast  48
Sharpness  32
Color  32
Colour Temp.  Normal
N.R. On
CTI On
Move SelectExit
 
						

							PR
PRV
O
L V
O
L
MENU
PREVPRSCREENSIZE
49
Press the Volume “ VOL ” Buttons.
•  Press the Volume “VOL” buttons to enter the
sub menu “Screen”.
•  While you are in ‘Screen’ menu, press the ”
PR” or 
“PR
” button to select a desired item, and then, ad-
just the value by pressing the  “
VOL”  or  “VOL” 
3
NOTES:
1)   Screen Menu is different according to the input modes.
2)  Other Screen adjustments
< Under PC mode >
[H. Position] :  As the value increases, the screen moves to the 
right.
[ V. Position] : As the value increases, the screen moves up.
[Auto] : Adjusting automatically the screen to optimum states.
< Under PIP mode >
[PIP Size] : Adjusting the size of the sub-picture.
[Alpha Blend] : Adjusting the translucent rate of the subpicture.
Picture
Sound
Screen
Feature
Install
Move AdjustExit
Mode 16 : 9 
H. Position.    32
V. Posi ti o n    32
Auto 
  
  
Adjusting Screen in the MENUAdjusting Screen in the MENU
•  This function is same
to the [Screen Size] of
remote controller.
Screen Mode
Function
< In case of PC input >
Input Available Screen Mode
AV / TV 16:9, 4:3, Panorama, LB(16:9), LBS(16:9), 
14:9, LB(14:9), LBS(14:9), Auto
Component, PC, DVI 16:9, 4:3, Panorama
 
						

							Still
50
Press the “STILL” Button.
•  If you wish to freeze a picture, press the 
“STILL” button. You can still hear the sound.
•  Press “STILL” button again to cancel the 
“STILL” function.
1
   Watching a STILL Image      Watching a STILL Image
•  You can view still images 
with this function. However,
displaying the same images
such as still images for a 
long time may cause image 
burn.
Watching a
Still Image
NOTES:
1)  Displaying the same images such as still images for a long
time may cause image burn (after-image lagging).
2)  In this case, such “image burn” may become less noticeable
if moving images are later displayed for a long time.
3)  However, an image burn may become a permanent one,
damaging the Plasma Display; therefore, avoid displaying
the same images for a long time.
4)  Use the function [ISM], while displaying still images for a long
period of time to minimize this effect.
ISM (on or off ) is in the Feature menu.
 
						

							Main
Sub
Sub
SubSub
SubMain
Main
Main

< Using  „PR”  and  „VOL”  
buttons>
Pip Size
Adjusting the size of the 
sub-picture with
 “VOL” 
buttons.
Alpha Blend
The adjustment of alpha
blend allows the sub-picture
to be translucent.
The translucent rate is
controlled with 
“VOL” 
buttons.
•  PIP (Picture-in-Picture) and P-by-P(Picture-by-Picture) modes allow users to watch two pictures simultaneously.
POP mode is used in searching memorized 5 or 12 channels.
51
Watching Two Pictures SimultaneouslyWatching Two Pictures Simultaneously
Engaging PIP mode
•  Press the ‘PIP’ button once on the remote control to 
engage the Picture-in-Picture mode.
•  By pressing the button repeatedly, it will show the 
following cycle.
•  If switched to P-by-P (Picture-by-Picture) mode, the 
screen will be split in half. The screen on the left side 
is the main picture, and the sub-picture will be on the 
right of the screen.
1
•  Size and Alpha Blend of the 
subpicture can be adjusted 
on Screen Menu of OSD.
•  These fuctions are availible  
only in PIP Mode.
Screen Adjustment
of the Sub-picture
Position of the Sub-picture
•  When PIP mode is engaged, the sub-picture can be displayed in 
one of the four corners by using ‚POSITION’ button.
•  Whenever pressing the button, the sub-picture will be cycling in 
the following order.
Also, using “
PR” and  “VOL” button, the sub-picture 
can be moved to any position you want.
2
Swap the pictures
•  In order to swap between the main picture and sub-
picture, press the ‘SWAP’ button.
•  However, at POP5 and POP12, the pictures are not
swapped. Main picture will change to the active sub-
picture.
•  Also, only TV channels are available for the sub-pictures of
POP5 and POP12.
The sub-pictures search channels continuously until POP 
mode is exited.
3
POP5
P-by-P PIP
Main
SubSub1
MainMain Sub2 Sub3
Sub4
Sub5
POP12
Sub1 Sub2
Sub9
Sub10 Sub11 Sub12
Sub3
Sub8Sub4
Sub5
Sub6
Sub7Main MainSub