Digital Projection Projector IVision50-series User Manual

							41
5.8.2 Settings > Network sub menu
change LAN settings: In this sub-menu you can switch the DHCP enabled function on or off.  
If off you can set a fixed IP-address.
LAN DHCP: DHCP is supported and is enabled by default, but can be disabled under  change 
LAN settings
LAN IP address:
 Info field stating the curr ent LAN IP address. 
LAN subnet mask: Info field stating the current LAN subnet mask.
LAN default gateway: Info field stating the current LAN default gateway.
LAN MAC address: Info field stating the current LAN MAC address.
TCP/UDP port: Info field stating the curr ent TCP/UDP port.
english   
						

							42User Manual - Introduction
5.8.3 Settings > Factory Reset sub menu
picture: Restores picture settings to factory default.
3D: Restores 3D settings to factory default.
communication: Restores communication settings to factory default.
ColorMaxTM: Restor es ColorMaxTM settings to factory default.
other: Restores other settings of your choice to factory default.
5.8.4 Settings > Service sub menu
service: Restricted ar ea  with information intended for qualified service personnel only
enter code: Enter the 5-digit access code to gain assess to the service information.\
iVision50-series  
User Manual - Overview
english   
						

							43
5.9 Languages menu
Select the desired menu language.•  
Supported languages: English, Fr
 ench, German, Spanish, Norwegian, Swedish, Russian, 
Korean, Japanese,Chinese Traditional, Chinese Simplified, Portuguese, Italian.
•
 
Default:
  English
english   
						

							44User Manual - Introduction
5.10 Status menu
source information: Simple and advanced source information.
synchronisation  
information:
 Gives information on the 3D (off/on) and 2D frame lock (source)
part number: Projector part number.
serial number: Projector serial number.  
manufactured (y): Year of manufacturing.
manufactured (w): Week of manufacturing.
software version: Software version installed in the projector.  
This is very important for service requests.
colorwheel:
 
T
 ype of colorwheel installed.
lamp remaining: Remaining lamp time.
lamp time: Lamp time used.
total operating: Total operating time for projector.
lamp power: Lamp power in watts.
IP address LAN: Projector IP address for use in network/remote control .  
iVision50-series  
User Manual - Overview
english   
						

							45
5.10.1 Status > Source Information sub menu
advanced: Access to sub menu for mor e settings depending on source used.  
See 4.10.2 Status > Source Information > Advanced sub menu
source: Info on which source is in use.
brightness: Info on  brightness settings. 
contrast: Info on  contrast settings. 
saturation: Info on saturation settings.  
gamma: Info on gamma-variant used.
english   
						

							46User Manual - Introduction
5.10.2 Status > Source Information > Advanced sub menu
sync frequency : Info on current horizontal and vertical sync frequency for the projector.
total image size: Info on current horizontal and vertical image size.
active image size: Info on current active image size.
scan: Pr ojector serial number.  
pixelclock: Week of manufacturing.
mode id: Info on curr ent mode setup (VGA source only).
iVision50-series  
User Manual - Overview
english   
						

							47
5.10.3 Status > Source Synchronisation sub menu
3D: Indicates which 3D mode is used.
2D frame lock: Indicates what the pr ojector locks to in 2D
Frequency: Shows the current frequency of the locking signal
Status: Indicates the locking status
Phase: Indicates phase between the sour ce and the locking signal
3D source sync: Indicates where the source L/R sync is connected
Frequency: Shows the current frequency of the signal
Duty cycle:
 
Shows the duty cycle of the signal
Status: Indicates the sync status
Phase: Indicates phase between the sour ce and the L/R sync signal
3D display sync: Indicates what the projector locks to in 3D
Frequency: Shows the current frequency of the locking signal
Duty cycle:
 
Shows the duty cycle of the signal
Status: Indicates the locking status
Phase: Indicates phase between the sour ce and the locking signal
english   
						

							48User Manual - IntroductioniVision50-series  
User Manual - Overview
english   
						

							49
6 Functionality
The various functions of the projector are described in detail in the following chapters.
6.1 Powering On and Off
6.1.1 Manual power contr ol
Switch the projector between On and Standby using the POWER switch on the keypad or 
the wireless remote control. 
The keypad STATUS indicator is blue when the projector is up and running, flashing yellow 
when cooling down and yellow when in standby. No status light indicates that the power has 
been switched off completely in the installation.
6.1.2 DPMS - power down
This is a power down mode which needs to be activated in the SETTINGS menu.   
When activated it powers down after a specified period of time after a\
 source has been 
removed. The time out setting can be specified in the DPMS TIMEOUT function in the same 
menu, using the arrow keys. 
6.2 Image alignment
Test images are built into the system for easier alignment of the projector
To access the test images, go to the menu entry INSTALLATION  > TEST IMAGE. Run 
through the various test images using the arrow keys. When a test image matching the as-
pect ratio of your screen has been found, you can match the screen using the zoom, focus, 
lens shift and aligning the projector physically.
6.2.1 Image orientation
The projector supports the following installation orientations (in relation to the screen): 
•
 
Desktop fr
 ont (default) 
•
 
Ceiling fr
 ont 
•
 
Desktop r
 ear 
•
 
Ceiling r
 ear 
To set the image orientation go to menu entry INSTALLATION > IMAGE ORIENTATION.
english   
						

							50User Manual - Introduction
6.3 Language
The menu system has a total of 11 user-selectable languages available. The default language 
is English. 
The available languages are: 
• 
English
  
•
 
Fr
 ench 
•
 
German
  
•
 
Spanish
  
•
 
Russian
  
•
 
Norwegian
  
•
 
Swedish
  
•
 
Kor
 ean 
•
 
Japanese
  
•
 
Chinese Simplified
  
•
 
Chinese T
 raditional 
•
 
Portuguese
  
•
 
Italian
  
To change the language of the menu system, just click top menu and select\
 your desired 
language.
6.4 System status
System status can be read at any time. STATUS is easily accessible from the top menu or by 
pushing the INFO button the wireless remote control. 
•
 
Part number
  
•
 
Serial number
  
•
 
The year/week the pr
 ojector was manufactured 
•
 
Curr
 ent software version 
•
 
Runtime and r
 emaining time for lamp
•
 
T
 otal number of operating hours 
•
 
All network information
  
•
 
Curr
 ently active source
Further source information is available by selecting STATUS > SOURCE INFORMATION.
If a deeper analysis is required for the currently active source, select STATUS > SOURCE 
INFORMATION > ADVANCED. This menu provides detailed timing information for the cur -
rently active source.
Setting custom color space and digital level
The projector will automatically try to set the correct color space and digital drive level based 
on information from the source.
For manual override of the automatically detected color space and digita\
l level, go to   
PICTURE > ADVANCED in the menu. Set the COLOR SPACE and INPUT LEVEL to one   
of the manual settings, choosing your desired color space and digital drive level.
iVision50-series   
User Manual - Functionality
english