Digital Projection Projector M-Vision 930 3D Series User Manual

page 3
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
What’s In The Box?Notes
 Make sure your box contains 
everything listed. If any pieces are 
missing, contact your dealer.
 You should save the original box 
and packing materials, in case you 
ever need to ship your projector.
 The projector is shipped without a 
lens.
 Only one power cable - dependent 
on the destination territory - will be 
supplied with the projector.
Remote control 
(115-758)
2x AA batteries
User Manual on disc 
(115-759)...

page 4
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Connecting The Power Supply
1. Make sure the voltage switch is 
set to the correct voltage.
2. Make sure the mains power 
button is in the OFF position.
3. Lift the cable lock up, push the 
mains connector in firmly and push 
the lock down to secure the cable.
4. Switch the mains power button 
ON.
Notes
 Use only the power cable 
provided.
 Ensure that the power outlet 
includes a ground connection as 
this equipment MUST be earthed....

page 5
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Projector Over view
Front and rear views
1 Air inlet
2 Lens
3 Front infrared window
4 Air inlet
5 Connection panel
6 Control panel
7 Rear infrared window
8 Lamp enclosures with air outlets
9 Mains inlet with power button and voltage switch
10 Air outlet
11 Adjustable feet
12 Air inlet
Notes
Front view
2
3
1
11
4
Rear view
8
7
6
5
9
12
10
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  

page 6
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Control panel indicators
During power on, all LED indicators become lit while the projector is 
running a self test.
At the end of the self test only the STANDBY indicator remains lit. 
When the projector goes from STANDBY to ON mode, the STANDBY 
indicator is switched off and the ON indicator is lit.
The ON indicator flashes during cool down.
Indicators
1 ON
2 ERROR
3 STANDBY
Error codes
If the projector detects an error, the red ERROR...

page 7
Installation and Quick-Start Guide
REMOTE CONTROL
Remote Control
1 Power ON / OFF
2 Transmit Indicator
Flashes when a button is pressed.
2 Input selection
Select input source.
3 Navigation
Navigate through the menus with the arrows, confirm your choice with ENTER.
4 MENU
Access the projector OSD (on-screen display).
5 User Memory
Load preset A, B or C.
6 CONTRAST
Bring up the Contrast control, then adjust the value with the LEFT and RIGHT 
arrow buttons..
7 GAMMA
Switch to the next Gamma value:...

page 8
Installation and Quick-Start Guide
REMOTE CONTROL
Remote control - continued from previous page
13 BRIGHTNESS
Bring up the Brightness control, then adjust the value with the LEFT and 
RIGHT arrow buttons.
14 O-SCAN
Switch to Overscan mode:
...Off, Crop, Zoom...
15 C-TEMP
Switch to the next color temperature:
...5400K, 6500K, 7500K, 9300K, Native...
16 3D SWAP
Switch 3D source dominance from left to right eye (left eye signal first) and vice 
versa.
17 SHARP
Bring up the Sharpness control, then...

page 9
Installation and Quick-Start Guide
REMOTE CONTROL
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance 
when trying to control the projector.
40°
40°
Infrared reception
Notes
   
Digital Projection M-Vision 930 Series 
Rev C Februar y 2015  

page 10
Installation and Quick-Start Guide
REMOTE CONTROL
Remote control troubleshooting
The remote control is shipped with no battery fitted. Remove the back cover and insert the 
supplied cells while observing the correct cell polarity.
If the projector fails to respond to keypress on the remote control, consider the following checks:
• Does the Transmit indicator flash when a button is pressed?
The Transmit indicator 1 should be dark when the remote control is not being used and 
flash when a button...

page 11
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. Set the adjustable feet so that 
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the fixing holes...

page 12
Installation and Quick-Start Guide
CHANGING THE LENS
Changing The Lens
Inserting a new lens
1. Remove the lens cover.
2. Insert the lens, keeping 
the connector in upright 
position.
3. Rotate the lens clockwise 
until it clicks into place.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
  Take care to preserve the original...