Home
>
Digital Projection
>
Projector
>
Digital Projection Projector M-Vision 930 3D Series User Manual
Digital Projection Projector M-Vision 930 3D Series User Manual
Have a look at the manual Digital Projection Projector M-Vision 930 3D Series User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 32
Connection Guide
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs ........................................................................\
...............................25
Digital inputs and outputs ........................................................................................25
Analog inputs ............................................................................................................26
EDID on the DVI and VGA inputs...](http://img.usermanuals.tech/thumb/5761/99623/w64_projector_manual_8413_d-31.png "Page 32
Connection Guide
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs ........................................................................\
...............................25
Digital inputs and outputs ........................................................................................25
Analog inputs ............................................................................................................26
EDID on the DVI and VGA inputs...")
![Page 35
page 27
Connection Guide
SIGNAL INPUTS
EDID on the DVI and VGA inputs
If you are using a computer DVI card or another source that obeys the EDID protocol, the source will automatically configure itself to suit the
projector.
Otherwise refer to the documentation supplied with the source to manuall\
y set the resolution to the DMD™ resolution of the projector or the
nearest suitable setting. Switch off the source, connect to the projector, then switch the source back on again.
Using HDMI/DVI switchers...](http://img.usermanuals.tech/thumb/5761/99623/w64_projector_manual_8413_d-34.png "Page 35
page 27
Connection Guide
SIGNAL INPUTS
EDID on the DVI and VGA inputs
If you are using a computer DVI card or another source that obeys the EDID protocol, the source will automatically configure itself to suit the
projector.
Otherwise refer to the documentation supplied with the source to manuall\
y set the resolution to the DMD™ resolution of the projector or the
nearest suitable setting. Switch off the source, connect to the projector, then switch the source back on again.
Using HDMI/DVI switchers...")
CONNECTION GUIDE4 Rev C Februar y 2015 M-Vision 930 Series High Brightness Digital Video Projector
Connection Guide IN THIS GUIDE IN THIS GUIDE Signal Inputs ........................................................................\ ...............................25 Digital inputs and outputs ........................................................................................25 Analog inputs ............................................................................................................26 EDID on the DVI and VGA inputs .............................................................................27 Using HDMI/DVI switchers with the projector ........................................................27 3D connections .........................................................................................................28 3D sources up to 60Hz requiring frame doubling and left/right interleaving ...................28 Frame sequential 3D sources up to 120Hz .....................................................................28 Dual Pipe 3D .....................................................................................................\ ..............28 3D Sync ......................................................................................................................29 3D Sync in .....................................................................................................\ ..................29 3D Sync out ....................................................................................................\ ................29 Control Connections ........................................................................\ ................30 LAN connection examples .......................................................................................31 RS232 connection example ......................................................................................32 Digital Projection M-Vision 930 Series Rev C Februar y 2015
page 25 Connection Guide SIGNAL INPUTS Signal Inputs Digital inputs and outputs 1 HDBaseT Receives digital signal from HDBaseT-compliant devices. 2 HDMI 1, HDMI 2, Dual Pipe 3D Two identical single HDMI 1.4 inputs which support HDCP 1.1 and DVI 1.0. Used together, the two sockets become a dual HDMI input which supports Dual Pipe 3D. Dual Pipe 3D supports sources up to 1920x1200 resolution at frame rates consistent with up to 148.5 Mpx/sec/pipe (including blanking). 3 DVI This input has a DVI-I connector, which can receive digital (DVI-D) signal from a compatible source. Supports sources up to 1920x1200 resolution, 24-120 Hz. Supports HDCP. Notes For a complete listing of all supported signal input modes, see Appendix C: Supported Signal Input Modes in the Reference Guide . For a complete listing of pin configurations for all signal and control connectors, see Appendix E: Wiring Details in the Reference Guide . The DVI input is designed to handle high bandwidth signals (above 60 Hz) in addition to lower frequencies. Digital connections 1 HDBaseT 2 HDMI 1 & HDMI 2 3 DVI 3 21 Digital Projection M-Vision 930 Series Rev C Februar y 2015
page 26 Connection Guide SIGNAL INPUTS Analog inputs 1 Component 1 2 Component 2 The Component inputs use colorspaces assigned from the Color Space setting in the Color menu. Set Color Space to Auto and the projector will automatically detect and assign the colorspace as required. Otherwise, assign the colorspace as follows: • When using RGsB, set Color Space to RGB PC or RGB Video. • When using YPbPr, set Color Space to YPbPr. • When using YCbCr, set Color Space to YCbCr. 3 VGA This input receives analog signals from a computer. When using this input, it is best to use a fully wired VGA cable to connect the source to the projector. This will allow the source to determine the projector’s capabilities via DDC and show an optimized image. Such cables can be identified as they have a blue connector shell. Analog connections 1 Component 1 2 Component 2 3 VGA 3 12 Notes For a complete listing of all supported signal input modes, see Appendix C: Supported Signal Input Modes in the Reference Guide . For a complete listing of pin configurations for all signal and control connectors, see Appendix E: Wiring Details in the Reference Guide . Digital Projection M-Vision 930 Series Rev C Februar y 2015
page 27 Connection Guide SIGNAL INPUTS EDID on the DVI and VGA inputs If you are using a computer DVI card or another source that obeys the EDID protocol, the source will automatically configure itself to suit the projector. Otherwise refer to the documentation supplied with the source to manuall\ y set the resolution to the DMD™ resolution of the projector or the nearest suitable setting. Switch off the source, connect to the projector, then switch the source back on again. Using HDMI/DVI switchers with the projector When using an HDMI/DVI source switcher with the projector, it is important to set the switcher so that it passes the projector EDID through to the source devices. If this is not done, the projector may not be able to lock to the source or display the source correctly as its video output timings may not be compatible with those of the projector. Sometimes this is called transparent, pass-through or clone mode. See \ your switcher’s manual for information on how to set this mode. 1Sources 2Switcher 3Projector Notes The EDIDs in the switcher should be the same as the one in the projector\ . 132 EDID EDID EDIDEDID Digital Projection M-Vision 930 Series Rev C Februar y 2015
page 28 Connection Guide SIGNAL INPUTS 3D connections 3D sources up to 60Hz requiring frame doubling and left/right interleaving 1. Connect to either of the following inputs on the connection panel: • HDMI 1 • HDMI 2 • HDBaseT 2. Set 3D Format in the 3D menu to match the format of the incoming signal. Choose from Auto, Side by Side (Half) and Top and Bottom. The Frame Packing format is automatically detected by the projector. Frame sequential 3D sources up to 120Hz • Connect to the DVI input. The Frame Sequential format is automatically detected by the projector and is supported on the DVI input only. Dual Pipe 3D 1. Connect the left eye output to the HDMI 1 socket and the right eye output to the HDMI 2 socket. 2. Set 3D Format in the 3D menu to Dual-Pipe. Notes For a complete listing of all supported signal input modes, see Appendix C: Supported Signal Input Modes in the Reference Guide . For a complete listing of pin configurations for all signal and control connectors, see Appendix E: Wiring Details in the Reference Guide . 1 HDBaseT 2 DVI 3 HDMI 1 / Dual Pipe LEFT 4 HDMI 2 / Dual Pipe RIGHT 423 1 Digital Projection M-Vision 930 Series Rev C Februar y 2015
page 29 Connection Guide SIGNAL INPUTS 3D Sync 3D Sync in Sync input signal. • Connect the 3D sync from your graphics card or server. 3D Sync out Sync output signal. This may be affected by the Sync Offset setting in the 3D menu. Connect this to your IR emitter or ZScreen. Notes For a complete listing of pin configurations for all signal and control connectors, see Appendix E: Wiring Details in the Reference Guide . 5 6 43 3 3D input 4 3D Sync In 5 3D Sync Out 6 IR emitter or ZScreen 1 Sync In 2 Sync Out 21 Digital Projection M-Vision 930 Series Rev C Februar y 2015
page 30 Connection Guide CONTROL CONNECTIONS Control Connections 1 LAN • All of the projector’s features can be controlled via a LAN connection, using commands described in the Protocol Guide. • Use a crossed LAN cable to connect directly to a computer, or an uncrossed cable to connect to a network hub. 2 RS232 • All of the projector’s features can be controlled via a serial connection, using commands described in the Protocol Guide. • Use a straight-through cable to connect directly to a computer. 3 Trigger 1 & Trigger 2 The Trigger outputs are activated by one of the three following conditions, as set in the Setup menu: • Screen trigger: can be connected to an electrically operated screen, automatically deploying the screen when the projector starts up, and retracting the screen when the projector shuts down. • Aspect ratio trigger: can be used to control screen shuttering for different aspect ratios. • RS232 trigger: can be used to control the screen or screen shuttering on receipt of an RS232 command 4 IR Input • If infrared signals from the remote control cannot reach the projector due to excessive distance or obstructions such as walls or cabinet doors, you can connect an external IR repeater to the remote control input, and position its IR sensor within range of the operator. 5 USB The USB port is used for firmware updates only. Notes For a list of all commands used to control the projector via LAN, see the Protocol Guide . For a complete listing of pin configurations for all signal and control connectors, see Appendix E: Wiring Details in the Reference Guide . Only one remote connection (RS232 or LAN) should be used at any one time. Control connections 1 5 234 Digital Projection M-Vision 930 Series Rev C Februar y 2015
page 31 Connection Guide CONTROL CONNECTIONS LAN connection examples The projector’s features can be controlled via a LAN connection, using a terminal-emul\ ation program. Notes ComputerProjector Projector Un-crossed LAN cables Hub or LAN 1 1LAN Projector Computer Crossed LAN cable Digital Projection M-Vision 930 Series Rev C Februar y 2015
page 32 Connection Guide CONTROL CONNECTIONS RS232 connection exampleNotes 1 1RS232 Projector Computer Straight- through cable Digital Projection M-Vision 930 Series Rev C Februar y 2015