Dukane Projector 6860WUSS-B User Manual

							78
[IMAGE OPTIONS]
Adjusting	Clock	and	Phase	[CLOCK/PHASE]
This	allows	you	to	manually	adjust	CLOCK	and	PHASE.
CLOCK �������������������Use this item to fine tune the computer image or to remove any vertical banding that might appear� This 
function adjusts the clock frequencies that eliminate the horizontal ban\
ding in the image�
This adjustment may be necessary when you connect your computer for the first time�
PHASE �������������������Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk� (This is 
evident when part of your image appears to be shimmering�)
Use [PHASE] only after the [CLOCK] is complete�
NOTE:	The	[CLOCK]	and	[PHASE]	items	are	available	for	RGB	signals	only.
5. Using On-Screen Menu  
						

							79
Adjusting	Horizontal/Vertical	Position	[HORIZONTAL/VERTICAL]
Adjusts	the	image	location	horizontally	and	vertically.
•	 An	image	can	be	distorted	during	the	adjustment	of	[CLOCK]	and	[PHASE].	This	is	not	malfunction.
•	 The	adjustments	for	[CLOCK],	[PHASE],	[HORIZONTAL],	and	[VERTICAL]	will	be	stored	in	memory	for	the	
current	signal.	The	next	time	you	project	the	signal	with	the	same	resolution,	horizontal	and	vertical	frequency,	
its	adjustments	will	be	called	up	and	applied.
	 To	delete	adjustments	stored	in	memory,	from	the	menu,	you	select	[RESET]	→	[CURRENT	SIGNAL]	and	reset	
the	adjustments.
[BLANKING]
Adjusts	the	display	range	(blanking)	at	the	top,	bottom,	left	and	right	edges	of	the	input	signal.
Selecting	Overscan	Percentage	[OVERSCAN]
Select	overscan	percentage	(Auto,	0%,	5%	and	10%)	for	signal.
Projected	image
Overscaned
	by	10%
NOTE: 
•	 The	[OVERSCAN]	item	is	not	available:
	 -		when	[NATIVE]	is	selected	for	[ASPECT	RATIO].
5. Using On-Screen Menu  
						

							80
Selecting	the	Aspect	Ratio	[ASPECT	RATIO]
Use	this	function	to	select	the	screen’s	vertical:horizontal	aspect	ratio.
Select	the	screen	type	(4:3	screen,	16:9	screen	or	16:10	screen)	at	the	screen	setting	before	setting	the	aspect	ratio.	
(→	page	97)
The	projector	automatically	identifies	the	signal	being	input	and	sets	the	optimum	aspect	ratio.
For Computer signal
For	Component/Video/S-Video	signals
When	the	screen	type	is	set	to	4:3When	the	screen	type	is	set	to	16:9	or	16:10
ResolutionAspect	RatioVGA640	×	4804:3
SVGA800	×	6004:3
XGA1024	×	7684:3
WXGA1280	×	76815:9
WXGA1280	×	80016:10
HD(FWXGA)1366	×	768approx.	16:9WXGA+1440	×	90016:10
SXGA1280	×	10245:4
SXGA+1400	×	10504:3
WXGA++1600	×	90016:9
UXGA1600	×	12004:3
WSXGA+1680	×	105016:10
FHD(1080P)1920	×	108016:9
WUXGA1920	×	120016:10
WQXGA2560	×	160016:10
Options Function
AUTO
The	projector	will	automatically	determine	the	incoming	signal	and	display	it	in	its	aspect	ratio.	The	projector	may	erroneously	determine	the	aspect	ratio	depending	on	its	signal.	If	this	occurs,	select	the	appropriate	aspect	ratio	from	the	following.
4:3The	image	is	displayed	in	4:3	aspect	ratio.
5:4The	image	is	displayed	in	5:4	aspect	ratio
16:9The	image	is	displayed	in	16:9	aspect	ratio
15:9The	image	is	displayed	in	15:9	aspect	ratio
16:10The	image	is	displayed	in	16:10	aspect	ratio
5. Using On-Screen Menu  
						

							81
OptionsFunction
NATIVE
The	projector	displays	the	current	image	in	its	true	resolution	when	the	incoming	computer	signal	has	a	lower	or	higher	resolution	than	the	projector’s	native	resolution.	(→	page	2)When	the	incoming	computer	signal	has	a	higher	resolution	than	the	projector's	native	resolution,	the	center	of	an	image	will	be	displayed.
LETTER	BOXThe	image	of	a	letterbox	signal	(16:9)	is	stretched	equally	in	the	horizontal	and	vertical	directions	to	fit	the	screen.
WIDE	SCREENThe	image	of	a	squeeze	signal(16:9)	is	stretched	left	and	right	in	16:9.
ZOOMThe	image	of	a	squeeze	signal	(16:9)	is	stretched	left	and	right	in	4:3.Parts	of	the	displayed	image	are	cropped	at	the	left	and	right	edges	and	therefore	not	visible.
FULLProject	to	full	screen	size.
TIP:
•	 Image	position	can	be	adjusted	vertically	using	[POSITION]	when	the	[16:9],	[15:9],	or	[16:10]	aspect	ratios	are	selected.
•	 The	term	“letterbox”	refers	to	a	more	landscape-oriented	image	when	compared	to	a	4:3	image,	which	is	the	standard	aspect	
ratio for a vide source.
	 The	letterbox	signal	has	aspect	ratios	with	the	vista	size	“1.85:1”	or	cinema	scope	size	“2.35:1”	for	movie	film.
•	 The	term	“squeeze”	refers	to	the	compressed	image	of	which	aspect	ratio	is	converted	from	16:9	to	4:3.
[INPUT	RESOLUTION]
The	resolution	is	assigned	automatically	when	the	resolution	of	the	input	signal	from	the	computer	video	input	terminal	
or	BNC	video	input	terminal	(analog	RGB)	cannot	be	distinguished.
5. Using On-Screen Menu  
						

							82
[VIDEO]
Using	Noise	Reduction	[NOISE	REDUCTION]
When	projecting	a	video	image,	you	can	use	the	[NOISE	REDUCTION]	function	to	reduce	the	screen	noise	(roughness	
and	distortion).	This	device	is	equipped	with	three	types	of	noise	reduction	functions.	Select	the	function	according	to	
the	type	of	noise.	Depending	on	the	noise	level,	the	noise	reduction	effect	can	be	set	to	[OFF],	[LOW],	[MEDIUM]	or	
[HIGH].	[NOISE	REDUCTION]	can	be	selected	for	SDTV,	HDTV	signal	and	component	signal	input.
RANDOM NR ���������Reduces flickering random noise in an image� 
MOSQUITO NR ������Reduces mosquito noise that appears around the edges of an image during \
Blu-ray playback�
BLOCK NR �������������Reduces block noise or mosaic-like patterns by selecting ON�
Selecting	Interlaced	Progressive	Conversion	Process	Mode	[DEINTERLACE]
This	function	allows	you	to	select	an	interlaced-to-progressive	conversion	process	for	video	signals.
NORMAL ����������������Automatically distinguishes a moving image from a static image to create\
 a distinct image� Please select 
[MOVIE] if there are any obvious jitter and noises�
MOVIE �������������������Select when projecting moving images� This is suitable for signals with a lot of jitter and noise�
STILL ���������������������Select when projecting static images� The video will flicker when a moving image is projected�
NOTE:	This	function	is	not	available	with	RGB	signals.
[CONTRAST	ENHANCEMENT]
Using	the	characteristics	of	the	human	eye,	a	picture	quality	with	a	sense	of	contrast	and	resolution	is	achieved.
OFF ������������������������Suite vision is switched off�
AUTO ���������������������Contrast and picture quality are automatically improved using the suite \
vision function�
NORMAL ����������������Adjust the gain manually�
5. Using On-Screen Menu  
						

							83
[SIGNAL	TYPE]
Selection	of	RGB	and	component	signals.	Normally,	this	is	set	to	[AUTO].	Please	change	the	setting	if	the	color	of	the	
image	remains	unnatural.
AUTO ���������������������Automatically distinguishes RGB and component signals�
RGB �����������������������Switches to the RGB input�
COMPONENT ���������Switches to the component signal input�
[VIDEO	LEVEL]
Selection	of	the	video	signal	level	when	connecting	an	external	device	to	the	HDMI	IN	terminal,	DisplayPort	input	
terminal,	and	HDBaseT	input	terminal	of	the	projector.
AUTO ���������������������The video level is switched automatically based on the information from \
the device outputting the signal�
Depending on the connected device, this setting may not be made properly� In this case, switch to [NORMAL” 
or “ENHANCED” from the menu and view with the optimum setting�
NORMAL ����������������This disables the enhanced mode�
ENHANCED ������������This improves the image’s contrast, expressing the dark and light sections more dynamically�
SUPER WHITE �������The video contrast is improved and the dark areas appear more dynamic�
5. Using On-Screen Menu  
						

							84
[3D SETTINGS]
Please	refer	to	“3-9	Projecting	3D	videos”	(→	page	38)	for	the	operation.
FORMAT
Select	the	3D	video	format	(recording	/	transmission	format).	Select	to	match	the	3D	broadcast	and	3D	media.	Nor-
mally,	[AUTO]	is	selected.	Please	select	the	3D	input	signal	format	when	the	3D	detection	signal	of	the	format	cannot	
be	distinguished.
L/R	INVERT
Invert	the	display	order	of	the	left	and	right	videos.
Select	[ON]	if	you	feel	uncomfortable	with	the	3D	display	when	[OFF]	is	selected.
5. Using On-Screen Menu  
						

							85
❻ Menu Descriptions & Functions [DISPLAY]
[PIP/PICTURE BY PICTURE]
SUB	INPUT
Select	the	input	signal	to	be	displayed	in	the	sub-display.
Please	refer	to	“4-2	Displaying	Two	Pictures	at	the	Same	Time”	(→	page	52)	for	details	on	the	operation.
MODE
Select	either	PIP	or	PICTURE	BY	PICTURE	when	switching	to	2-screen	display.
PICTURE	SWAP
The	videos	in	the	main	display	and	sub-display	will	be	switched.
Please	refer	to	“4-2	Displaying	Two	Pictures	at	the	Same	Time”	(→	page	54)	for	details.
PIP	SETTING
Select	the	display	position,	position	adjustment	and	size	of	the	sub-display	in	the	PIP	screen.
START POSITION ���Selection of the display position of the sub-display when switching to t\
he PIP screen�
HORIZONTAL POSITION
 ������������������������������Adjust the display position of the sub-display in the horizontal directi\
on� The respective corners will serve 
as reference points�
VERTICAL POSITION
 ������������������������������Adjust the display position of the sub-display in the vertical direction� The respective corners will serve as 
reference points�
SIZE �����������������������Select the display size of the sub-display�
5. Using On-Screen Menu  
						

							86
TIP:
The	horizontal	position	and	vertical	position	are	the	amount	of	movement	from	the	reference	points.	For	example,	when	TOP-LEFT	
is adjusted, the position is displayed with the same amount of movement \
even if displayed with other starting positions.
The maximum amount of movement is half the resolution of the projector.
Reference	point
Adjust	using	the	horizon-
tal	position
Sub-display Main
	display
Reference
	point
Adjust
	using	the	vertical	position
TOP-LEFT TOP-RIGHT
BOTTOM-LEFT BOTTOM-RIGHT
Reference
	point
Reference	point
BORDER
Select	the	display	boundary	of	the	main	display	and	sub-display	of	the	[PICTURE	BY	PICTURE]	screen.
Display	boundary
Main	displaySub-display
Main	displaySub-displayMain	display
Sub-display
TIP:
•	 6	steps	can	be	selected	on	this	projector.
5. Using On-Screen Menu  
						

							87
[GEOMETRIC CORRECTION]
KEYSTONE
Display	the	trapezoid	correction	screen	and	adjust	the	trapezoidal	distortion	of	the	projection	screen.
To	display	the	[KEYSTONE]	screen,	select	→	[DISPLAY]	→	[GEOMETRIC	CORRECTION]	→	[KEYSTONE]	in	the	
on-screen	menu.	The	[GEOMETRIC	CORRECTION]	screen	can	also	be	displayed	by	pressing	the	3D	REFORM	
button	on	the	remote	control.
HORIZONTAL ���������Adjustments when projecting from a diagonal direction to the 
screen�
VERTICAL ��������������Adjustments when projecting from the top or bottom direction to 
the screen�
TILT �����������������������Adjusts the distortion when performing trapezoidal correction with the screen moved in the vertical direction 
using the lens shift�
THROW RATIO �������Adjusts according to the projection ratio of the optional lens used�
Model	name	of	lens	unitAdjustment	range
NP34ZL9–13
NP35ZL 12–17
NP36ZL 12–17
NP37ZL 15–31
NOTE:
•	 When	power	is	supplied	to	the	device,	the	adjustment	value	of	the	[KEYSTONE]	used	previously	is	retained	even	if	the	gradient	
of the device is changed.
•	 When	clearing	the	adjustment	value	of	[KEYSTONE],	press	the	3D	REFORM	button	for	2	or	more	seconds.
•	 When	setting	other	[GEOMETRIC	CORRECTION]	functions,	the	[KEYSTONE]	menu	cannot	be	selected.	When	performing	trapezoidal	
correction,	press	the	3D	REFORM	button	for	2	or	more	seconds	to	clear	the	adjustment	value	of	[GEOMETRIC	CORRECTION].
•	 As	electrical	correction	is	carried	out	by	[KEYSTONE],	the	brightness	may	be	reduced	or	the	screen	quality	may	deteriorate	
sometimes.
5. Using On-Screen Menu